Teknik Clifton Place 5421116 User manual

www.teknikoffice.co.uk
Hutch
Clifton Place Collection | Model 5421116
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
For things 'n such.
Teknik

Table of Contents Assembly Tools Required
3
4
5-14
15-17
18-20
21-22
23
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Page 2
Electric drill with 1/4" bit
(ONLY in indicated step)

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
C TOP (1)
D BRACE (1)
E MOLDING (2)
F UPPER ADJUSTABLE SHELF (1)
G LOWER ADJUSTABLE SHELF (1)
H BACK (1)
Now you know
our ABCs.
Page 3
A
B
C
D
E
F
G
H
E

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
Page 4
CAM SCREW - 4
2
APPLIQUE CARD - 1
8
WOOD DOWEL - 4
3
RUBBER SLEEVE - 8
6
METAL PIN - 8
5
SHORT WOOD
DOWEL - 4
4
BLACK 1-1/2" FLAT HEAD SCREW - 4
10 BLACK 1-1/8" FLAT HEAD SCREW - 6 11
SILVER 5/8" FLAT HEAD SCREW - 6
13
BLACK 1" PAN HEAD SCREW - 8
12
HIDDEN CAM - 4
1
FURNITURE TIPPING RESTRAINT KIT - 1
99
BACK CONNECTOR - 6
7
BRACKET - 2
9

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Insert four HIDDEN CAMS (1) into the TOP (C).
Page 5
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
(4 used)
1
Arrow
C
Surface with groove

Step 2
å Insert four WOOD DOWELS (3) into the ENDS (A and B).
å Turn four CAM SCREWS (2) into the ENDS (A and B).
å Insert four SHORT WOOD DOWELS (4) into the MOLDINGS (E).
Page 6
A
B
E
E
3
2
4
3

å Fasten the MOLDINGS (E) to the TOP (C). Use six BLACK
1-1/8" FLAT HEAD SCREWS (11).
å NOTE: Be sure the SHORT WOOD DOWELS in the
MOLDINGS insert into the TOP.
Step 3
Page 7
Groove
EE
C
BLACK 1-1/8" FLAT HEAD SCREW
(6 used in this step)
11
Remember:
Righty tighty.
Lefty loosey.

Step 4
å Fasten the TOP (C) to the LEFT END (B). Tighten two
HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWEL in the LEFT END
inserts into the TOP.
å Unfold the BACK (H) and slide the BACK into the grooves
in the TOP (C) and LEFT END (B).
Page 8
C
Groove
C
B
H
B
1
2
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution
NOTE: Position the
BACK exactly as shown.
Finished surface
without tape

å Place the BRACE (D) onto the WOOD DOWEL in the LEFT END (B).
å NOTE: Be sure the BACK inserts into the groove in the BRACE.
å Fasten RIGHT END (A) to the TOP (C). Tighten two HIDDEN CAMS.
å NOTE: Be sure the BACK inserts into the groove in the RIGHT END.
å NOTE: Be sure the WOOD DOWELS in the RIGHT END insert into
the TOP and BRACE.
Step 5
Page 9
C
A
Groove
D
B
Groove

Step
å Carefully turn your unit over onto its front edges.
å Fasten the ENDS (A and B) to the BRACE (D). Use two BLACK
1-1/2" FLAT HEAD SCREWS (10).
å Insert six BACK CONNECTORS (7) into the grooves in the
ENDS (A and B). Space the BACK CONNECTORS as shown in
the diagram.
å NOTE: You may need to gently tap them in with your hammer.
å Fasten the BACK (H) to your unit. Use six SILVER 5/8" FLAT
HEAD SCREWS (13) through the BACK CONNECTORS and
into the ENDS.
Step 6
Page 10
BLACK 1-1/2" FLAT HEAD SCREW
(2 used in this step)
10
D
A
B
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution
H
7
7
SILVER 5/8" FLAT HEAD SCREW
(6 used in this step)
13

StepStep 7
å Carefully turn the Hutch over onto its back.
å If you are fastening the Hutch to the 421114, Lateral File, you will need to complete Steps 1-18 in the 421114
book before fastening the Hutch to the Lateral File Top.
å If you are fastening the Hutch to the 421115, Library Base, you will need to complete Steps 1-10 in the 421115
book before fastening the Hutch to the Library Base Top.
å The following steps show the Hutch being fastened to the Library Base.
å Finish drilling the two holes shown in the bottom surface of the Library Base Top using a 1/4" drill bit. Follow
the diagram.
å Next, fasten the Library Base Top to the ENDS (A and B). Use two BLACK 1-1/2" FLAT HEAD SCREWS (10).
Page 11
Finish drilling these two
holes from the bottom
surface. Use a 1/4" drill bit.
A
B
Library Base Top
Library Base Top
BLACK 1-1/2" FLAT HEAD SCREW
(2 used in this step)
10
The large hole is
closer to this edge.

Step
å With someone's help, fasten the Library Base Top to the
Library Base Assembly. Tighten six HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the Library Base Top
insert into the Library Base.
å NOTE: If needed, follow the 421114 or 421115 instruction book
to finish the assembly of the Lateral File or Library Base.
Step 8
Page 12
Library Base Top

StepStep 9
å Finish fastening the Hutch to the Library Base. Use two
BRACKETS (9) and eight BLACK 1" PAN HEAD SCREWS (12).
Page 13
9
BLACK 1" PAN HEAD SCREW
(8 used in this step)
12

Step
å We recommend using the FURNITURE TIPPING RESTRAINT KIT (99) for added stability. Fasten a bracket to the back
edge of the TOP (C) using the 5/8" screw as shown.
å Place your unit in its final location against a wall.
å Follow the instructions included in the KIT to fasten your unit to the wall.
å Push the RUBBER SLEEVES (6) over the METAL PINS (5). Insert the METAL PINS into the hole locations of your choice
in the ENDS (A and B). Set the ADJUSTABLE SHELVES (F and G) onto the METAL PINS.
å Peel the STICKERS from the APPLIQUE CARD (8) and stick one onto each visible HIDDEN CAM and SCREW.
å NOTE: Please read the back pages of the instruction booklet for important safety information.
å This completes assembly. Clean with your favorite furniture polish or a damp cloth. Wipe dry.
Step 10
Page 14
99
Use the 5/8" screw through the
small hole in a bracket and into
the back edge of the TOP (C). Small hole
C
F
(8 used)
5
6
8
To cover visible
HIDDEN CAMS
and SCREWS
No load
25 lbs.
G
25 lbs.
A
B

WARNING
Please use your furniture correctly and safely. Improper use can cause safety hazards,
or damage to your furniture or household items. Carefully read the following chart.
Look out for: What can happen: How to avoid the problem:
• Overloaded shelves. • Risk of injury.
• Overloaded shelves can break.
• Never exceed the weight limits shown in
the instructions
• Use the supplied tipping restraint kit for
added stability.
• Improperly moving furniture that is not
designed and equipped with casters.
• Furniture can tip over or break if
improperly moved.
• Physical injury. Furniture can be very
heavy.
• Unload shelves before moving the hutch.
• The hutch should be removed from the
desktop before attempting to move the desk.
• Do not push furniture, especially on a
carpeted floor. Have a friend help you lift
the item and set it in place.
• Placing TVs on furniture items that are not
designed to support a television is
hazardous.
• Risk of injury or death. TVs can be very
heavy. Plus the weight and location of the
picture tube tends to make TVs unbalanced
and prone to tipping forward.
• This product is not designed to support a
television.