Teknik 5427134 User manual

Iron Foundry Double Pedestal Desk
Model 5427134
For all your
newfanled gadgetry.
Teknik
www.teknikoffice.co.uk

Part Identification
Hardware Identification
Assembly Steps
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Table of Contents Assembly Tools Required
3
4
5-16
Pae 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the ede
to help distinuish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A TOP (1)
B MODESTY PANEL (1)
C LEFT END /UPRIGHT(2)
D RIGHT END/UPRIGHT (2)
E BACK (2)
F CABINET BOTTOM (2)
G DRAWER FRONT (2)
H LEFT DRAWER SIDE (2)
J RIGHT DRAWER SIDE (2)
K DRAWER BACK (2)
L DRAWER BOX FRONT (2)
N DRAWER BOTTOM (2)
O BOTTOM (2)
P SHORT BRACE (4)
Q END FRAME (2)
R UPRIGHT FRAME (2)
S LONG BRACE (1)
A
B
C
C
D
D
E
E
F
F
G
G
H
H
J
J
K
K
L
L
N
N
O
O
P
P
P
P
Q
Q
R
R
S
Pae 3

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
1-9/16" PAN HEAD SCREW - 8
12
1-7/8" HEX HEAD SCREW - 4
11
7/8" PAN HEAD SCREW - 8
17
1-3/8" HEX HEAD SCREW - 34
13 14 114" MACHINE SCREW  4
1-3/16" FLAT HEAD SCREW - 16
15
CAM SCREW - 1
4WOOD DOWEL - 40 5 6 ADJUSTABLE
GLIDE - 8
(EXTENSION SET SHOWN SEPARATED)
HIDDEN CAM - 1
3
1EXTENSION RAIL - 4 2EXTENSION SLIDE - 4
L-WRENCH - 1
9
PULL - 2
7FILE GLIDE - 4 8APPLIQUE CARD - 1
10
Pae 4
3/8" FLAT HEAD SCREW - 24
16

Step 1
å Assemble your unit on a carpeted floor or on the empty carton to avoid scratchin your unit or the floor.
å Separate the EXTENSION SLIDES (2) from the EXTENSION RAILS (1) as shown in the upper diaram below. Be
prepared, the parts are reasy.
å Fasten the EXTENSION RAILS (1) to the ENDS/UPRIGHTS (C and D). Use six 3/8" FLAT HEAD SCREWS (16).
å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlared diaram. Then, slide the inner
cartride of the EXTENSION RAIL in to find the other holes that lines up with the holes in the END./UPRIGHTS. Turn a
SCREW into these holes.
å NOTE: The EXTENSION SLIDES (2) will be used later for the DRAWERS.
å Repeat this step.
Open end
There should be two
holes on this ede.
There should be two
holes on this ede.
Open end
C
D
1
1
Pull the black lever down and pull the SLIDE from the RAIL.
1
2
Pae 5
3/8" FLAT HEAD SCREW
(12 used in this step)
16

å Insert four WOOD DOWELS (5) into a BACK (E).
å Push a set of ENDS/UPRIGHTS (C and D) onto the
WOOD DOWELS (5) in the BACK (E).
å Insert four WOOD DOWELS (5) into the edes of the
END/UPRIGHTS (C and D).
å Turn the cabinet onto its back. Fasten a CABINET
BOTTOM (F) to the END/UPRIGHTS (C and D). Use four
1-9/16" PAN HEAD SCREWS (12).
å NOTE: Be sure the WOOD DOWELS in the ENDS/
UPRIGHTS insert into the BOTTOM (F).
å Repeat this step.
Step 2
C
C
E
E
D
D
F
5
5
5
1-9/16" PAN HEAD SCREW
(8 used in this step)
12
Pae 6
Some assembly
(and snacks) required.
(16 used)

Hardware Usae Guide
HOW TO USE A HIDDEN CAM & CAM SCREW OR CAM DOWEL
NOTE: Various CAM SCREWS or a CAM DOWEL may be used.
Cam Screws Cam Dowel
Turn the CAM SCREW or
ently tap the CAM DOWEL
until the shoulder is aainst
the surface of the part.
1.
Hidden CamHidden Cam
Arrow
Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the
ede of the board.
Hole
2.
3.
1
2
Insert the CAM SCREW or CAM DOWEL into the
HIDDEN CAM. Tihten the HIDDEN CAM.
Pae 7

Step 3
å Push a HIDDEN CAM (3) into the MODESTY PANEL (B).
å Fasten the UPRIGHT FRAMES (R) to the MODESTY
PANEL (B). Tihten four 1-7/8" HEX HEAD SCREWS (11)
usin the L-WRENCH (9).
å Fasten the LONG BRACE (S) to the UPRIGHT
FRAMES (R). Tihten two 1-3/8" HEX HEAD
SCREWS (13) usin the L-WRENCH (9). 3
Arrow
1-7/8" HEX HEAD SCREW
(4 used in this step)
11
9
B
B
S
R
R
Surface with HIDDEN CAM
1-3/8" HEX HEAD SCREW
(2 used in this step)
13
Pae 8
Do not tihten the HIDDEN CAM in this step.

Step 4
å Fasten the SHORT BRACES (P) to the UPRIGHT
FRAMES (R). Tihten four 1-3/8" HEX HEAD
SCREWS (13) usin the L-WRENCH (9).
å Fasten the END FRAMES (Q) to the SHORT BRACES (P).
Tihten four 1-3/8" HEX HEAD SCREWS (13) usin
the L-WRENCH (9).
å NOTE: Do not completely tihten the 1-3/8" HEX HEAD
SCREWS at this time.
1-3/8" HEX HEAD SCREW
(8 used in this step)
13
Q
Q
R
R
9
Pae 9
P
P
P
P

å Fasten the BOTTOMS (O) to the UPRIGHT
FRAMES (R) and END FRAMES (Q). Turn four 1-3/8"
HEX HEAD SCREWS (13) usin the L-WRENCH (9).
å NOTE: Do not completely tihten the 1-3/8" HEX HEAD
SCREWS at this time.
å Turn eiht ADJUSTABLE GLIDES (6) completely into the
UPRIGHT FRAMES (R) and the END FRAMES (Q).
å NOTE: The ADJUSTABLE GLIDES are used to level
your desk and will be adjusted after the unit is
standin upriht in the last step.
Step 5
1-3/8" HEX HEAD SCREW
(8 used in this step)
13
6
6
Q
Q
R
R
13
13
13
O
O
9
Pae 10
Side Step: Make
nachos. (Optional, but
recommended.)