Teknik Stationmaster 5426454 User manual

For all your
newfanled gadgetry.
Stationmaster L-Shaped Desk
Model 5426454
Teknik
www.teknikoffice.co.uk

Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Table of Contents Assembly Tools Required
2-3
4-5
6-28
29-32
33-36
37-38
39
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the ede
to help distinuish similar parts from each other. Use this part identification to help identify similar parts.
A SHELF (1)
B BOTTOM (1)
C UPRIGHT (1)
D RIGHT END (1)
E BACK (1)
F SMALL DRAWER FRONT (1)
G SMALL LEFT DRAWER SIDE (1)
H SMALL RIGHT DRAWER SIDE (1)
J SMALL DRAWER BACK (1)
K SMALL DRAWER BOTTOM (1)
L LARGE DRAWER FRONT (1)
M LARGE LEFT DRAWER SIDE (1)
N LARGE RIGHT DRAWER SIDE (1)
O LARGE DRAWER BACK (1)
P DRAWER BOX FRONT (1)
Q LARGE DRAWER BOTTOM (1)
R LARGE TOP (1)
S SMALL TOP (1)
T LARGE MODESTY PANEL (1)
U SMALL MODESTY PANEL (1)
V LEG (1)
W LEFT END (1)
X BRACE (1)
Part Identification
Pae 2

Part Identification Now you know
our ABCs.
A
B
C
D
E
F
G
H
J
K
L
M
N
O
PQ
R
S
TU
V
W
X
Pae 3

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
GROMMET
WITH CAP- 2
10
L-WRENCH - 1
14
TIE PLATE - 1
12
CAM SCREW - 14
5THIN WOOD DOWEL - 8
8
HIDDEN CAM - 14
6WIDE WOOD
DOWEL - 12
7
9FILE GLIDE - 2
(EXTENSION SET SHOWN SEPARATED)
APPLIQUE CARD - 1
13
NARROW EXTENSION
RAIL - 2
WIDE EXTENSION
RAIL - 2
13
NARROW EXTENSION
SLIDE - 2
WIDE EXTENSION
SLIDE - 2
24
Pae 4
KNOB SET - 2
11

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
9/16" PAN HEAD SCREW - 4
22
1-9/16" PAN HEAD SCREW - 4
16
21 1316" MACHINE SCREW  2
2-1/3" HEX HEAD SCREW - 8
15
1/2" HEX HEAD SCREW - 1
23 1/2" FLAT HEAD SCREW - 24 24
1" PAN HEAD SCREW - 4
20
1-3/16" FLAT HEAD SCREW - 12
18
1-9/16" HEX HEAD SCREW - 2
17
1" HEX HEAD SCREW - 9
19
Pae 5

Hardware Usage Guide
HOW TO USE A HIDDEN CAM & CAM SCREW OR CAM DOWEL
NOTE: Various CAM SCREWS or a CAM DOWEL may be used.
Cam Screws Cam Dowel
Turn the CAM SCREW or
gently tap the CAM DOWEL
until the shoulder is against
the surface of the part.
1.
Hidden CamHidden Cam
Arrow
Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the
edge of the board.
Hole
2.
3.
1
2
Insert the CAM SCREW or CAM DOWEL into the
HIDDEN CAM. Tighten the HIDDEN CAM.
Pae 6

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratchin your unit or the floor.
å Turn four CAM SCREWS (5) into the SHELF (A).
å Push four HIDDEN CAMS (6) into the UPRIGHT (C) and
RIGHT END (D).
Pae 7
5
A
C
D
6
6
Some assembly
(and snacks) required.

å Separate the WIDE EXTENSION SLIDES (4) from the WIDE EXTENSION RAILS (3) as shown in the
diaram below. Be prepared, the parts are reasy.
å Separate the NARROW EXTENSION SLIDES (2) from the NARROW EXTENSION RAILS (1) as shown in
the diaram below. Be prepared, the parts are reasy.
å Fasten the EXTENSION RAILS (1 and 3) to the UPRIGHT (C) and RIGHT END (D). Use twelve 1/2" FLAT
HEAD SCREWS (24).
å NOTE: For each WIDE EXTENSION RAIL, turn a SCREW into the hole shown in the enlared diaram.
Then, slide the inner cartride of the WIDE EXTENSION RAIL in to find the other holes that line up with
the holes in the RIGHT END and UPRIGHT. Turn a SCREW into these holes.
å NOTE: The EXTENSION SLIDES will be used later for the DRAWERS.
Step 2
Pae 8
D
3
4
2
1
1/2" FLAT HEAD SCREW
(12 used in this step)
24
Push the release lever up or down and pull the SLIDE from the RAIL.
Open end
These bumpers
must be here.
1
3
C
This hole
must be here.
Open end
Surface with HIDDEN CAMS
3
1

å Insert four WIDE WOOD DOWELS (7) into the SHELF (A).
å Fasten the SHELF (A) to the UPRIGHT (C) and RIGHT
END (D). Tihten four HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the SHELF insert
into the holes in the UPRIGHT and RIGHT END.
Step 3
Pae 9
D
C
A
7
(4 used)
Ede without holes
Surface without
HIDDEN CAMS
Surface with
HIDDEN CAMS
These bumpers
must be here.

å Insert four WIDE WOOD DOWELS (7) into the BACK (E).
å Insert the WOOD DOWELS in one ede of the BACK (E)
into the SHELF (A)
Step 4
Pae 10
A
E
C
D
E
7
(4 used)