Teknik 5431262 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Shaker Style Bookcase with Doors Raven Oak
Model 5431262
Here's one for
the books.
Teknik
www.teknikoffice.co.uk

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Hardware Usage Guide
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
3
4
5, 7
5-22
23-25
26-28
29-30
31
Page 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
Page 3
A RIGHT END (1)
B LEFT END (1)
C2 TOP (1)
D BOTTOM (1)
E SHELF (1)
F BACK (1)
G DOOR (2)
H ADJUSTABLE SHELF (2)
I SMALL ADJUSTABLE SHELF (1)
J RIGHT LEG (1)
K LEFT LEG (1)
L BASE (1)
M TOP MOLDING (1)
N SHELF MOLDING (1)
O ADJUSTABLE SHELF MOLDING (2)
P SPACER (1)
A
B
C2
D
E
F
G
H
I
K
L
M
N
O
H
O
P
G
J

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
Page 4
BLACK 9/16" LARGE HEAD SCREW - 16
1S BLACK 1/2" FLAT HEAD SCREW - 8 11S
CAM SCREW - 8
8F
HIDDEN CAM - 20
1F CAM DOWEL - 12 2F
GOLD 1" MACHINE SCREW - 2
50S
BROWN 1-1/2" FLAT HEAD SCREW - 2
14S
METAL BRACKET - 8
4G
METAL PIN - 12
1R RUBBER SLEEVE - 12 2R FURNITURE TIPPING
RESTRAINT KIT - 1
97
12P CAM
COVER - 12
DOOR STOP - 2
4I NAIL - 60 1N
KNOB SET - 2
136K14H HINGE - 4

Hardware Usage Guide
Cam Screw
Hidden Cam
Arrow
Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the
edge of the board.
Hole
2. 3.
1
2
Insert the CAM SCREW into the HIDDEN CAM.
Tighten the HIDDEN CAM.
HOW TO USE A HIDDEN CAM & CAM SCREW
Turn the CAM SCREW
until the shoulder is against
the surface of the part.
1.
Look for this icon. It means a video assembly tip is
available at www.sauder.com/service/tips
Find the numbered video or scan the QR code.
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Turn four CAM SCREWS (8F) into the LEFT LEG (K).
Page 5
1
Step 1
8F
K

Step 2
å Push six HIDDEN CAMS (1F) into the LEFT END (B).
å Fasten the LEFT LEG (K) to the LEFT END (B). Tighten
four HIDDEN CAMS.
1F
Arrow
1F Arrow
B
Surface with
HIDDEN CAMS
KEdge with
HIDDEN CAMS
These surfaces
should be even.
B
Page 6
Some assembly
(and snacks) required.

Hardware Usage Guide
Do not tighten the HIDDEN CAMS in this step.
HOW TO USE A HIDDEN CAM & CAM DOWEL 2. Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
1. Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the
edge of the board.
Hole
Arrow
Metal end
Hidden Cam
Cam Dowel
Start Tighten
Arrow
Minimum
190 degrees
Caution
Risk of damage or
injury. HIDDEN CAMS
must be completely
tightened. HIDDEN
CAMS that are not
completely tightened
may loosen, and parts
may separate. To
completely tighten:
Arrow
Maximum
210 degrees
3.
Step 3
å Push four HIDDEN CAMS (1F) into the SHELF (E). Then,
insert the metal end of a CAM DOWEL (2F) into each
HIDDEN CAM.
Page 7
1
E
1F
2F
Arrow
Metal end
1F
2F
Metal end
Arrow

Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution
Step 4
å Fasten the SHELF (E) to the LEFT END (B). Tighten two
HIDDEN CAMS.
å Slide the SHELF MOLDING* (N) onto the notched edge of
the SHELF (E).
å *U.S. Patent No. 5,499,886
B
K
Surface with
HIDDEN CAMS
EN
Surface with HIDDEN CAMS
Slide the SHELF MOLDING (N)
onto the notched edge.
Notched edge
The large
groove is closer
to this edge.
Page 8

Step 5
å Turn four CAM SCREWS (8F) into the RIGHT LEG (J).
å Push six HIDDEN CAMS (1F) into the RIGHT END (A).
å Fasten the RIGHT LEG (J) to the RIGHT END (A). Tighten
four HIDDEN CAMS.
A
J
8F
1F
Arrow
1F Arrow
A
J
Surface with
HIDDEN CAMS
Edge with
HIDDEN CAMS
These surfaces
should be even.
Page 9

Step 6
å Push four HIDDEN CAMS (1F) into the BOTTOM (D).
Then, insert the metal end of a CAM DOWEL (2F) into
each HIDDEN CAM.
å Fasten the BOTTOM (D) to the LEFT END (B). Tighten two
HIDDEN CAMS.
å Fasten the RIGHT END (A) to the BOTTOM (D) and
SHELF (E). Tighten four HIDDEN CAMS.
B
E
D
A
J
Surface without
HIDDEN CAMS
These holes must be here.
Page 10
D
1F
2F
Arrow
Metal end
1F
2F
Metal end
Arrow