Teknik 5427455 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS
IMPORTANT SAFETY
INFORMATION.
PLEASE READ AND KEEP
FOR FUTURE REFERENCE.
English pg 1-15
Français pg 16-18
Español pg 19-21
1800 Low Reception
Hutch
Hudson Elm finish | Model 5427455
12/22/21 Lot # 574109
Purchased:
__________________
Teknik
www.teknikoffice.co.uk

Table of Contents Assembly Tools Required
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Hardware Identification
Part Identification
Hardware Usage Guide
Assembly Steps
Français
Español
Safety
Warranty
2
3
5
5-15
16-18
19-21
22
23
Page 2
Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
TAPE CARD/
PREP PAD KIT - 1
182M
Isopropyl
Alcohol 70%
Prep Pad
1S BLACK 9/16" LARGE HEAD SCREW - 8
10M TOUCH-UP PEN - 1 41G PLATE - 2
TWIST-LOCK®
FASTENER COVER - 23
125P
42F WOOD DOWEL - 16

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A RIGHT END (1)
B LEFT END (1)
C LONG TOP (1)
D SHORT TOP (1)
E UPRIGHT (2)
F SHORT BACK (1)
G LONG BACK (1)
A
B
C
D
E
E
F
G
Page 3

Hardware Usage Guide
1. Insert the dowel end of the FASTENER into the
hole of the adjoining part.
NOTE: The dowel end of the FASTENER must
remain fully inserted in the hole of the adjoining
part while locking the FASTENER.
2. Tighten the FASTENER with a Phillips
screwdriver as tight as possible.
Dowel end
2.
Push a TWIST-LOCK® FASTENER
into the large hole in the part.
1.
HOW TO USE A TWIST-LOCK®FASTENER
Step 1
å You have the option to use the Reception Hutch
as a Straight or a Corner.
å If you want the Reception Hutch to be used as a
Straight, go to the next step.
å If you want the Reception Hutch to be used as a
Corner, go to Step 8
Straight (Left or Right)
Steps 2 - 7
Corner
Steps 8 - 18
Page 5

Step 2
F
å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching
your unit or the floor.
å Insert three WOOD DOWELS (42F) into the SHORT BACK (F) exactly as shown.
å NOTE: You may need to gently tap the WOOD DOWEL in with your hammer.
å Fasten the ENDS (A and B) and one of the UPRIGHTS (E) to the SHORT BACK (F).
Tighten five TWIST-LOCK® FASTENERS.
å NOTE: Be sure the WOOD DOWELS in the LONG BACK insert into the
ENDS and UPRIGHT.
Surface with
TWIST-LOCK®
FASTENERS
Surface with
TWIST-LOCK®
FASTENERS
Edge with
TWIST-LOCK®
FASTENERS
Edge with
TWIST-LOCK®
FASTENERS
Edge with
TWIST-LOCK®
FASTENERS
Surface with
TWIST-LOCK®
FASTENERS
Surface without
TWIST-LOCK®
FASTENERS
E
A
B
42F
(3 used)
Page 6

å Insert five WOOD DOWELS (42F) into the
ENDS (A and B), UPRIGHT (E), and SHORT BACK (F).
å NOTE: You may need to gently tap the WOOD DOWEL in
with your hammer.
å Fasten the LONG TOP (C) to the ENDS (A and B),
UPRIGHT (E), and SHORT BACK (F)
Step 3
F
C
A
B
42F
(5 used)
E
Page 7
Just think. The sooner
you do this, the sooner
you do something else.

Step 4
å Your 427455 Reception Hutch can be fastened
to a Desk/Credenza and Desk Return combo in
either orientation.
427413
427422
427413
427422
Page 8

Step 5
427422
427413
Isopropyl
Alcohol 70%
Prep Pad
182M
å This unit is made to sit on the 427422 Desk/Credenza and the
427413 Desk Return. Open the TAPE CARD/PREP PAD KIT (182M)
and open the Alcohol Prep Pad to wipe the top surface of the Desk
and Return as shown in the diagram.
å Peel four double stick strips from the TAPE CARD and stick them
onto the edges of the Desk and Return as shown at the positions
marked 1 if you want your unit on the left.
å Peel four double stick strips from the TAPE CARD and stick them
onto the edges of the Desk and Return as shown at positions
marked 2 if you want your unit on the right.
å Next, peel the paper covering from the double stick strips.
182M
Wipe the top surface of
the Desk in this area.
1
1
2
2
Page 9

Step 6
å IMPORTANT: The Reception Hutch cannot be moved after it is set in place.
Pre-plan the Reception Hutch placement, then place it completely on the
attaching surface.
å With the help of another person, carefully center the Reception Hutch
onto your 427422 Desk/Credenza and the 427413 Desk Return in your
chosen position.
å NOTE: The back edges of the
Reception Hutch and Desk must be even.
STOP
The Reception Hutch
cannot be moved after it
is set in place. Pre-plan
the Reception Hutch
placement, then place
it completely on the
attaching surface.
Caution
Two person
lift required
427422
427413
The back
edges must
be even.
Page 10

Step 7
å Using your hammer, gently tap a TWIST-LOCK® FASTENER COVER (125P) onto each visible TWIST-LOCK® FASTENER.
å For long-term care and maintenance of your unit, you may touch up the edges with the TOUCH-UP PEN (10M).
å NOTE: Please read the back pages of the instruction booklet for important safety information.
å This completes assembly. Clean with a damp cloth. Wipe dry.
10M
125P
(22 used)
Page 11
50 lbs.