Teknik Craft 5427456 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Work Table/Island
Craft Collection | Model 5427456
Knick-knack
paddywhack,
ive your stu a home.
Teknik
www.teknikoffice.co.uk

No. 2 Phillips Screwdriver
Tip Shown Actual Size
Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
3
4
5-23
24-26
27-29
30
31
Pae 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
Pae 3
A END (2)
B RIGHT UPRIGHT (1)
C LEFT UPRIGHT (1)
D TOP (1)
E BOTTOM (1)
F UPPER SHELF (2)
G LOWER SHELF (2)
H UPPER CENTER SHELF (1)
I LOWER CENTER SHELF (1)
J CENTER UPRIGHT (1)
K SMALL UPRIGHT (2)
L BRACE (2)
M BOTTOM FRAME (1)
N DRAWER FRONT (6)
O DRAWER SIDE (6)
P DRAWER BOTTOM (3)
A
B
C
D
E
F
G
H
I
J
K
L
G
M
N
O
O
P
A
F
K
L
N

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
APPLIQUE CARD - 10
8
KNOB - 6
7
9SILVER 1316" FLAT HEAD SCREW  4
SILVER 1/2" PAN HEAD SCREW - 8
1210 SILVER 1316" MACHINE SCREW  4
HIDDEN CAM - 56
1WOOD DOWEL - 12 3
CAM SCREW - 56
2LONG WOOD
DOWEL - 4
4
SMALL WOOD
DOWEL - 4
5SMALL LONG
WOOD DOWEL - 4
6
13 SILVER 12" MACHINE SCREW  8
METAL BRACKET - 4
14 GLUE - 1 15
16 SILVER 1116" MACHINE SCREW  6
Pae 4

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratchin your unit or the floor.
å Push fifty-six HIDDEN CAMS (1) into the UPRIGHTS (B
and C), BOTTOM (E), SHELVES (F, G, H, and I), and
DRAWER SIDES (O).
1
Arrow
Arrow
The arrow in the HIDDEN
CAM must point toward the
hole in the ede of the board.
Hole
B
C
E
(56 used)
O
O
O
O
O
O
G
G
F
F
I
H
Some assembly
(and snacks) required.
Pae 5

Step 2
Pae 6
å Turn forty-eiht CAM SCREWS (2) into the exact holes
shown in the ENDS (A), UPRIGHTS (B and C), TOP (D),
and DRAWER FRONTS (N).
å NOTE: Be sure to use the exact holes shown.
å Fasten four METAL BRACKETS (14) to the ENDS (A).
Use four SILVER 1/2" MACHINE SCREWS (13).
å NOTE: Be sure the BRACKETS are even with the
edes of the ENDS.
2(48 used)
A
A
B
C
D
Meet Part (D). This component has
been enineered to be lihter, stroner,
faster… well ok. Not technically faster.
But definitely makes for a sturdier Work
Table that’s easier to assemble and
friendlier to the environment.
N
N
N
N
N
N
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
SILVER 1/2" MACHINE SCREW
(4 used in this step)
13
14

Step 3
Pae 7
å Insert three WOOD DOWELS (3) into the exact holes
shown in one of the ENDS (A).
å Fasten the SHELVES (F and G) to the END (A). Tihten
four HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the END insert
into the holes in the SHELVES.
A
G
F
Surface with
HIDDEN CAMS
1
2
Surface with
HIDDEN CAMS
Surface with
CAM SCREWS
3

Step 4
Pae 8
å Insert two SMALL WOOD DOWELS (5) into one of the
SMALL UPRIGHTS (K).
å Push the SMALL WOOD DOWELS in the SMALL
UPRIGHT (K) into the exact holes shown in the END (A).
A
K
5

Step 5
Pae 9
B
C
å Turn eiht CAM SCREWS (2) into the exact holes shown
in the other surfaces of the UPRIGHTS (B and C).
å NOTE: Be sure to use the exact holes shown.
2(8 used)
Surface without
HIDDEN CAMS
Surface without
HIDDEN CAMS

Step 6
Pae 10
å Insert two LONG WOOD DOWELS (4) into the exact holes
shown in the SHELVES (F and G).
å Insert two SMALL LONG WOOD DOWELS (6) into the
holes in the SMALL UPRIGHT (K).
å Fasten the LEFT UPRIGHT (C) to the SHELVES (F and G).
Tihten four HIDDEN CAMS.
å NOTE: Be sure the LONG WOOD DOWELS in the
SHELVES and SMALL UPRIGHT insert throuh the holes
in the LEFT UPRIGHT.
G
F
K
C
46
Notch Surface without
HIDDEN CAMS