Teknik Wide Bookcase 5420282 User manual

www.teknikoffice.co.uk
Wide Bookcase
Hampstead Park Collection | Model 5420282
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
The stories of your life.
Teknik

Table of Contents Assembly Tools Required
3
4
5-18
19-21
22-24
25-26
27
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
Page 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
C TOP (1)
D BOTTOM (1)
E UPPER SHELF (1)
F MIDDLE SHELF (1)
G LOWER SHELF (1)
H ADJUSTABLE SHELF (1)
I SKIRT (2)
J RIGHT FRONT/LEFT REAR FOOT (2)
K LEFT FRONT/RIGHT REAR FOOT (2)
L TOP MOLDING (1)
M LEFT DOOR (1)
N RIGHT DOOR (1)
O BACK (1)
Now you know
our ABCs.
Page 3
A
B
C
D
E
F
G
H
I
J
K
L
MN
O
I
J
K

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
HIDDEN CAM - 32
1CAM SCREW - 32 2SHORT WOOD
DOWEL - 4
4
LONG WOOD
DOWEL - 32
3
APPLIQUE CARD - 1
10
BLACK 1/2" FLAT HEAD SCREW - 16
14
BLACK 1/2" PAN HEAD SCREW - 8
13
FURNITURE TIPPING RESTRAINT KIT - 1
99 12 BLACK 1-1/4" FLAT HEAD SCREW - 4
DOOR HANDLE - 2
7
METAL PIN - 4
8RUBBER SLEEVE - 4 9NAIL - 53 11
LOWER GUIDE - 4
6
UPPER GUIDE - 4
5
Page 4

Step 1
å Assemble your unit on a carpeted floor or on the empty carton to
avoid scratching your unit or the floor.
å Push thirty-two HIDDEN CAMS (1) into the TOP (C), BOTTOM (D),
SHELVES (E, F, and G), SKIRTS (I), and FEET (J and K).
Arrow
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
Hole
1
Arrow
(32 used)
Arrow
1
1
Arrow
Arrow
1
Page 5
C
D
E
F
G
I
I
K
J

Step 2
å Turn thirty-two CAM SCREWS (2) into the exact holes shown
in the ENDS (A and B), BOTTOM (D), and FEET (J and K).
Page 6
2
(32 used)
A
D
B
K
J

å Insert thirty-two LARGE WOOD DOWELS (3) into the
exact holes shown in the edges of the ENDS (A and B),
TOP (C), BOTTOM (D), SHELVES (E, F, and G), SKIRTS (I),
and FEET (J and K).
Step 3
Page 7
3
3
(32 used)
C
D
E
F
G
I
I
Some assembly
(and snacks) required.
3
K
J

Step 4
å Fasten the SKIRTS (I) to the FEET (J and K). Tighten four
HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the SKIRTS insert
into the FEET.
Page 8
1
2
I
J
K
I
J
K
Edge with WOOD DOWELS
Surface with HIDDEN CAMS

å Fasten the SKIRTS (I) and FEET (J and K) to the BOTTOM (D).
Tighten eight HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the SKIRTS and FEET
insert into the BOTTOM.
Step 5
Page 9
D
I
K
J
K
J
Surface with HIDDEN CAMS
I
Surface without HIDDEN CAMS
Surface with CAM SCREWS

Step 6
å Fasten the TOP MOLDING (L) to the TOP (C). Use four
BLACK 1-1/4" FLAT HEAD SCREWS (12).
å NOTE: Do not over tighten the SCREWS into the TOP.
Page 10
BLACK 1-1/4" FLAT HEAD SCREW
(4 used in this step)
12
CL
Surface without HIDDEN CAMS
Finished edge