Teknik Barrister Home 5420176 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
3-Shelf Bookcase
Barrister Home | Model 5420176
The stories of your life.
Teknik
www.teknikoffice.co.uk

Table of Contents Assembly Tools Required
3
4
5-14
15
Part Identification
Hardware Identification
Assembly Steps
Safety
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Page 2
Skip the power trip.
This time.
Tape Measure

Part Identification Now you know
our ABCs.
Page 3
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
E2 TOP (1)
F BOTTOM (1)
H2 BACK (1)
J ADJUSTABLE SHELF (2)
K END MOLDING (2)
M25 TOP MOLDING (1)
M48 BASE (1)
N SHELF MOLDING (2)
A
B
E2
F
J
H2
M25
N
M48
K
K
NJ

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
Page 4
ANGLE BRACKET - 5
27G
HIDDEN CAM - 8
1F CAM DOWEL - 8 2F
METAL PIN - 8
1R
CAM COVER - 4
13P HOLE PLUG - 3 14P
NAIL - 30
1N
BLACK 1-1/8" PAN HEAD SCREW - 3
9S
BLACK 9/16" LARGE HEAD SCREW - 10
1S
FURNITURE TIPPING RESTRAINT KIT - 1
97

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Push eight HIDDEN CAMS (1F) into the ENDS (A and B)
and BOTTOM (F). Then insert the metal end of a CAM
DOWEL (2F) into each HIDDEN CAM.
Page 5
A
B
F
Arrow
1F
2F
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
Do not tighten the HIDDEN CAMS in this step.
(8 used)

Step 2
Page 6
å Fasten the ENDS (A and B) to the BOTTOM (F). Tighten four
HIDDEN CAMS.
A
B
F
Start Tighten
Arrow
Minimum
190 degrees
Caution
Risk of damage or
injury. HIDDEN CAMS
must be completely
tightened. HIDDEN
CAMS that are not
completely tightened
may loosen, and parts
may separate. To
completely tighten:
Arrow
Maximum
210 degrees
Notched edge
Notched edge
These holes must be here.
Surface with
HIDDEN CAMS
Surface without
HIDDEN CAMS
Surface with
HIDDEN CAMS
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution

Step 3
Page 7
å Open the FURNITURE TIPPING RESTRAINT KIT (97)
and fasten the SAFETY STRAP to the TOP (E2). Use the
provided BLACK 9/16" LARGE HEAD SCREW.
å NOTE: Position the SAFETY STRAP exactly as shown.
å Fasten the TOP (E2) to the ENDS (A and B). Tighten four
HIDDEN CAMS.
A
B
Arrow
Minimum
190 degrees
Maximum
210 degrees
E2
Surface with holes
E2
Surface with holes
Long finished edge
BLACK 9/16" LARGE HEAD SCREW
(1 used for the SAFETY STRAP)
Safety strap
97

Step 4
å Fasten the TOP MOLDING (M25) to the TOP (E2). Use
three BLACK 1-1/8" PAN HEAD SCREWS (9S).
å NOTE: Do not overtighten the SCREWS into the TOP.
å Insert three HOLE PLUGS (14P) into the holes in the
TOP MOLDING (M25).
Page 8
E2
Curved edge
BLACK 1-1/8" PAN HEAD SCREW
(3 used in this step)
9S
14P
Remember:
Righty tighty.
Lefty loosey.
M25

å Slide the END MOLDINGS* (K) onto the notched edges of
the ENDS (A and B).
å *U.S. Patent No. 5,499,886
Step 5
Page 9
A
B
K
K
Slide the END MOLDINGS (K)
onto the notched edges.
Notched edge
Notched edge
The large groove is
closer to this edge.
The large groove is
closer to this edge.

Step 6
å Fasten five ANGLE BRACKETS (27G) to the ENDS (A
and B) and BOTTOM (F). Use five BLACK 9/16" LARGE
HEAD SCREWS (1S).
å NOTE: Be sure the edges of the ANGLE BRACKETS are
even with the edges of the ENDS and BOTTOM.
å Fasten the BASE (M48) to the ANGLE BRACKETS. Use
five BLACK 9/16" LARGE HEAD SCREWS (1S).
Page 10
BLACK 9/16" LARGE HEAD SCREW
(10 used in this step)
1S
F
B
A
27G
27G
27G
Wide edge
M48