Teknik Barrister 5420330 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
www.teknikoffice.co.uk
Barrister Home Side Table
Model 5420330
Gets on your couch’s
good side.
Teknik

Table of Contents Assembly Tools Required
3
4
5-23
Part Identification
Hardware Identification
Assembly Steps
Page 2
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
C TOP (1)
D BOTTOM (1)
E SHELF (1)
F BACK (1)
G BASE (2)
H SIDE BASE (2)
I VALANCE (1)
J DRAWER FRONT (1)
K SIDE TOP MOLDING (2)
L TOP MOLDING (2)
M END MOLDING (4)
P PLINTH (4)
D22 DRAWER RIGHT SIDE (1)
D23 DRAWER LEFT SIDE (1)
D77 DRAWER BACK (1)
D706 DRAWER BOTTOM (1)
Now you know
our ABCs.
Page 3
A
B
C
D
E
F
G
H
I
J
K
L
M
P
D706
D77
D23
D22
P
P
PG
H
K
L
M
M
M

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
Page 4
31G CORNER BRACKET - 4
35AA UNIVERSAL CABINET RAIL - 2 35AC DRAWER RIGHT - 1 35AD DRAWER LEFT - 1
BLACK 9/16" LARGE HEAD SCREW - 42
1S
SILVER 1-1/8" FLAT HEAD SCREW - 10
10S 15S SILVER 5/8" MACHINE SCREW - 2
MOLDING
CONNECTOR - 4
17F
3S GOLD 5/16" FLAT HEAD SCREW - 8
10A SLIDE CAM - 2
BROWN 1-5/8" FLAT HEAD SCREW - 8
55S
HIDDEN CAM - 8
1F CAM DOWEL - 8 2F
BLACK 1-15/16" FLAT HEAD SCREW - 4
113S
30S BLACK 1-9/16" FLAT HEAD SCREW - 4
EXTENSION BRACKET - 4
45G PULL - 1 98K

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Push eight HIDDEN CAMS (1F) into the ENDS (A and B)
and SHELF (E). Then, insert the metal end of a CAM
DOWEL (2F) into each HIDDEN CAM.
Page 5
Arrow
1F
2F
(8 used)
Arrow
1F
2F
Do not tighten the HIDDEN CAMS in this step.
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
A
B
E

Step 2
å Tap four MOLDING CONNECTORS (17F) into the notches
in the TOP MOLDINGS (K and L).
Page 6
K
L
KL
Flat end
Use your hammer to tap the MOLDING CONNECTORS (17F) into the notches in the TOP MOLDINGS.
Flat end
Flat end
Flat end
Unfinished surface
Unfinished surface
Unfinished surface
17F
17F
17F
17F

å Carefully turn the assembled TOP MOLDINGS (K and L) over.
å Fasten the TOP MOLDINGS (K and L) to the TOP (C). Use
eight BROWN 1-5/8" FLAT HEAD SCREWS (55S).
å NOTE: Do not overtighten the SCREWS into the TOP.
Step 3
Page 7
C
KL
K
L
Flat edge
Rounded edge
Surface
with holes
Curved edge
Do not overtighten
the SCREWS (55S).
BROWN 1-5/8" FLAT HEAD SCREW
(8 used in this step)
55S
Remember:
Righty tighty.
Lefty loosey.

Step 4
å Slide the END MOLDINGS (M) onto the notched edges of
the ENDS (A and B).
å *U.S. Patent No. 5,499,886
Page 8
Slide the END MOLDING (M)
onto the notched edge.
Groove
Groove
A
Surface with
HIDDEN CAMS
B
Surface with
HIDDEN CAMS
Notched edge
Notched edge
M
M
M
M

å Place the BACK (F) on edge on the LEFT END (B)
against the END MOLDING (M).
å Fasten the SHELF (E) to the LEFT END (B). Tighten
two HIDDEN CAMS.
Step 5
Page 9
Start Tighten
Arrow
Minimum
190 degrees
Caution
Risk of damage or
injury. HIDDEN CAMS
must be completely
tightened. HIDDEN
CAMS that are not
completely tightened
may loosen, and parts
may separate. To
completely tighten:
Arrow
Maximum
210 degrees
E
Surface with
HIDDEN CAMS
B
Surface with
HIDDEN CAMS
Notch
M
F
Unfinished
surface
These holes
must be here.
Edge with
CAM DOWELS

Step 6
Page 10
Arrow
Minimum
190 degrees
Maximum
210 degrees
å Fasten the RIGHT END (A) to the SHELF (E). Tighten two
HIDDEN CAMS.
å NOTE: Be sure to center the BACK (F) evenly between the
ends of the END MOLDINGS (M).
M
Edge with
CAM DOWELS
A
Surface without
HIDDEN CAMS
F
M
The edge of the BACK (F)
should be even with the end
of the END MOLDING (M).
E