Teknik Trestle 5410421 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Trestle Desk
5410421 Cinnamon Cherry
5417061 Soft White
You could totally write
a novel on this.
Teknik
www.teknikoffice.co.uk

Table of Contents Assembly Tools Required
3
4
5-14
15-17
18-20
21-22
23
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
Pae 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the ede
to help distinuish similar parts from each other. Use this part identification to help identify similar parts.
A END (2)
B RIGHT UPRIGHT (1)
C LEFT UPRIGHT (1)
D TOP (1)
E BACK (1)
F FRONT (2)
G STRETCHER (2)
H RIGHT FRONT/LEFT REAR LEG (2)
I LEFT FRONT/RIGHT REAR LEG (2)
J DRAWER FRONT (1)
D266 RIGHT DRAWER SIDE (1)
D267 LEFT DRAWER SIDE (1)
D268 DRAWER BACK (1)
D269 DRAWER BOX FRONT (1)
D622 DRAWER BOTTOM (1)
Now you know
our ABCs.
Pae 3
A
A
B
C
D
EF
FG
G
H
H
I
I
J
D266D268
D267
D269
D622

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
Pae 4
35DA CABINET RIGHT - 1 35DB CABINET LEFT - 1 35DC DRAWER RIGHT - 1 35DD DRAWER LEFT - 1
HIDDEN
CONNECTOR - 8
5F PULL - 1
104K SCREW COVER - 8
20P METAL PIN - 8 1R
CONNECTOR SCREW - 8
8S
BLACK 7/8" LARGE HEAD SCREW - 2
17S
BLACK 1-7/8" FLAT HEAD SCREW - 16
2S 3S GOLD 5/16" FLAT HEAD SCREW - 8
BLACK 1-5/8" PAN HEAD SCREW - 2
27S
BLACK 1-1/8" PAN HEAD SCREW - 8
9S
30S BLACK 1-9/16" FLAT HEAD SCREW - 4

Step 1
å Insert a CONNECTOR SCREW (8S) into each
HIDDEN CONNECTOR (5F).
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratchin your unit or the floor.
å Use your hammer to tap two HIDDEN CONNECTORS (5F)
with SCREWS into one of the ENDS (A).
å Repeat this step for the other END (A), RIGHT UPRIGHT (B),
and LEFT UPRIGHT (C).
Step 2
8S
5F
A
5F
(8 used)
Pae 5

Step 3
å Insert eiht METAL PINS (1R) into the ENDS (A)
and STRETCHERS (G).
å Insert the METAL PINS (1R) in the ENDS (A) and
STRETCHERS (G) into the holes in the LEGS (H and I).
å Now, fasten the LEGS (H and I) to the ENDS (A) and
STRETCHERS (G). Use eiht BLACK 1-7/8" FLAT
HEAD SCREWS (2S).
Pae 6
1R
1R
1R
1R
A
A
G
G
H
H
I
I
Surface with HIDDEN CONNECTOR
These edes
should be even.
These edes
should be even.
These edes
should be even.
These edes
should be even.
Surface with HIDDEN CONNECTOR
BLACK 1-7/8" FLAT HEAD SCREW
(8 used in this step)
2S

å Fasten the BACK (E) and FRONTS (F) to the LEGS (H and I).
Use eiht BLACK 1-1/8" PAN HEAD SCREWS (9S).
å Fasten the ENDS (A) to the BACK (E) and FRONTS (F). Use
four BLACK 1-7/8" FLAT HEAD SCREWS (2S).
Step 4
Pae 7
A
E
F
F
H
H
I
I
This surface should be the
same finish as this surface.
This surface should be the
same finish as this surface.
A
BLACK 1-7/8" FLAT HEAD SCREW
(4 used for the ENDS)
2S
BLACK 1-1/8" PAN HEAD SCREW
(8 used for the LEGS)
9S

Step 5
å Fasten the ENDS (A) to the TOP (D). Tihten four
HIDDEN CONNECTORS.
Pae 8
A
A
D
How to use the HIDDEN CONNECTOR
To fasten two parts together using the
HIDDEN CONNECTORS, insert your
screwdriver, at an angle, into the slot in the
HIDDEN CONNECTOR. While pushing the
screw into the hole of the adjoining part,
turn the screwdriver clockwise to tighten.
Lon finished ede
Unfinished surface
Hey! It's startin to look
like somethin!

å Fasten the UPRIGHTS (B and C) to the TOP (D).
Tihten four HIDDEN CONNECTORS.
å Fasten the UPRIGHTS (B and C) to the BACK (E)
and FRONTS (F). Use four BLACK 1-7/8" FLAT
HEAD SCREWS (2S).
Step 6
Pae 9
B
D
E
F
F
C
Surface with HIDDEN CONNECTORS
Finished ede
Surface with HIDDEN
CONNECTORS
BLACK 1-7/8" FLAT HEAD SCREW
(4 used in this step)
2S

Step 7
å Fasten the CABINET RIGHT (35DA) to the RIGHT
UPRIGHT (B) and the CABINET LEFT (35DB) to the
LEFT UPRIGHT (C). Use four GOLD 5/16" FLAT HEAD
SCREWS (3S) throuh holes #1 and #3.
Pae 10
1
1
2
2
3
3
B
C
35DB
35DB
Roller end
35DA
35DA
GOLD 5/16" FLAT HEAD SCREW
(4 used in this step)
3S