Teknik 5418295 User manual

www.teknikoffice.co.uk
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Hutch for Scribed Oak Storage Desk (5418294)
5418295
For things 'n such.
Teknik

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Safety
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Hammer
Not actual size
3
4
5-17
18
Page 2
Short Screwdriver
Skip the power trip.
This time.

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A RIGHT END (1)
B LEFT END (1)
C UPRIGHT (1)
D TOP (1)
E SHELF (1)
F RIGHT BACK (1)
G LEFT BACK (1)
H DIVIDER (3)
I SKIRT (1)
J FRONT MOLDING (1)
K RIGHT MOLDING (1)
L LEFT MOLDING (1)
Page 3
A
B
C
D
E
F
GH
I
J
K
L
H
H

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
Page 4
BLACK 9/16" LARGE HEAD SCREW - 3
1S
BLACK 1-1/4" FLAT HEAD SCREW - 9
7S
BLACK 1-7/8" FLAT HEAD SCREW - 3
2S
36P CAM COVER - 10
MOLDING
CONNECTOR - 2
17F
METAL PIN - 11
1R
NAIL - 36
1N
HIDDEN CAM - 12
1F CAM DOWEL - 12 2F

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Push twelve HIDDEN CAMS (1F) into the ENDS (A and B),
UPRIGHT (C), SHELF (E), and SKIRT (I). Then, insert the
metal end of a CAM DOWEL (2F) into each HIDDEN CAM.
Page 5
A
B
C
E
I
Arrow
1F
2F
(12 used)
Arrow
1F
2F
Do not tighten the HIDDEN CAMS in this step.
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow

å Tap two MOLDING CONNECTORS (17F) into the notches
in the MOLDINGS (J, K, and L).
Step 2
Page 6
K
J
17F
17F
L
Use your hammer to tap the MOLDING CONNECTOR (17F) into the notches in the MOLDINGS.
Flat end
Flat end

å Turn the MOLDINGS (J, K, and L) over and fasten them
to the TOP (D). Use nine BLACK 1-1/4" FLAT HEAD
SCREWS (7S).
Step 3
Page 7
D
K
J
L
Surface with holes
Remember:
Righty tighty.
Lefty loosey.
Finished surface
Finished surface
Rounded edge
BLACK 1-1/4" FLAT HEAD SCREW
(9 used in this step)
7S

å Fasten the RIGHT END (A) to the RIGHT MOLDING (K).
Tighten two HIDDEN CAMS.
Step 4
Page 8
Start Tighten
Arrow
Minimum
190 degrees
Caution
Risk of damage or
injury. HIDDEN CAMS
must be completely
tightened. HIDDEN
CAMS that are not
completely tightened
may loosen, and parts
may separate. To
completely tighten:
Arrow
Maximum
210 degrees
A
K
J
Curved edge
Surface with
HIDDEN CAMS
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution

å Insert three METAL PINS (1R) into the holes shown in the
TOP (D).
å Slide the DIVIDERS (H) onto the METAL PINS (1R) in the
TOP (D).
å Now, insert six METAL PINS (1R) into the other end of the
DIVIDERS (H).
Step 5
Page 9
D
H
H
H
J
1R
1R
All curved edges should face
the FRONT MOLDING (J).

å Fasten the SHELF (E) to the RIGHT END (A). Tighten two
HIDDEN CAMS.
å NOTE: Be sure the METAL PINS in the DIVIDERS (H)
insert into the holes in the SHELF.
Step 6
Page 10
A
H
H
H
E
Surface with
HIDDEN CAMS
Arrow
Minimum
190 degrees
Maximum
210 degrees
Finished edge