Teknik New Hyde 426440 User manual

Hythe Wall Mounted Hallway
Storage
New Hyde Collection | Model 426440
You'll love what we
have in storage.
Teknik
www.teknikoffice.co.uk

Part Identification
Hardware Identification
Assembly Steps
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Table of Contents Assembly Tools Required
3
4-5
6-21
Page 2
Electric drill with 5/16" bit
(ONLY in indicated step)

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A FRONT (1)
B LEFT END (1)
C RIGHT END (1)
D BACK (1)
E BOTTOM (1)
F TOP (1)
G LEFT LEG (1)
H RIGHT LEG (1)
J BRACE (2)
K RACK (1)
L LOWER FRAME (2)
M UPPER FRAME (2)
N ROD (1)
A
B
C
D
E
F
G
H
J
J
K
L
L
M
M
N
Page 3

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
CAM SCREW - 4
2
HIDDEN CAM - 4
1WOOD DOWEL -12
3REAR HINGE - 3
4
LEFT HINGE - 1
5RIGHT HINGE - 1 67BUMPER CARD - 1 APPLIQUE CARD - 1
8
WALL ANCHOR - 2
9WASHER - 4 10 L-WRENCH - 1
11
Page 4

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
1/2" HEX HEAD SCREW - 8
14 1-9/16" PAN HEAD SCREW - 12
15
1-3/16" HEX HEAD SCREW - 18
12 2" PAN HEAD SCREW - 2 13
Page 5
BLACK 9/16" PAN HEAD SCREW - 23
16 1-3/8" HEX HEAD SCREW - 4
17

Hardware Usage Guide
HOW TO USE A HIDDEN CAM & CAM SCREW OR CAM DOWEL
NOTE: Various CAM SCREWS or a CAM DOWEL may be used.
Cam Screws Cam Dowel
Turn the CAM SCREW or
gently tap the CAM DOWEL
until the shoulder is against
the surface of the part.
1.
Hidden CamHidden Cam
Arrow
Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the
edge of the board.
Hole
2.
3.
1
2
Insert the CAM SCREW or CAM DOWEL into the
HIDDEN CAM. Tighten the HIDDEN CAM.
Page 6

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Turn four CAM SCREWS (2) into the FRONT (A).
å Push four HIDDEN CAMS (1) into the ENDS (B and C).
A
B
C
2
Arrow
1
Page 7
Just think. The sooner
you do this, the sooner
you do something else.

Step
å Insert two WOOD DOWELS (3) into the FRONT (A).
å Fasten the ENDS (B and C) to FRONT (A). Tighten four
HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the FRONT insert
into the ENDS.
Step 2
A
B
C
Notch
Finished edge
3
3
Page 8

Step
å Insert two WOOD DOWELS (3) into the ENDS (B and C).
å Fasten the BACK (D) to the ENDS (B and C). Use four
1-9/16" PAN HEAD SCREWS (15).
å NOTE: Be sure the WOOD DOWELS in the ENDS insert
into the BACK.
Step 3
B
C
D
3
1-9/16" PAN HEAD SCREW
(4 used in this step)
15
Surface with fewer holes
Notched edge
Page 9

Step
å Carefully turn your unit on its top edges.
å Insert eight WOOD DOWELS (3) into the SHELF (E).
å Fasten the BOTTOM (E) to the FRONT (A), ENDS (B and C),
and BACK (D). Use eight 1-9/16" PAN HEAD SCREWS (15).
å NOTE: Be sure the WOOD DOWELS in the SHELF insert
into the FRONT, ENDS and BACK.
Step 4
B
C
D
A
E
3
(8 used)
These holes are further from this edge
1-9/16" PAN HEAD SCREW
(8 used in this step)
15
Page 10