Teknik Contemporary Bureau 5416966 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
For all your
newfanled gadgetry.
Contemporary Bureau
5416966
Teknik
www.teknikoffice.co.uk

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
3
4
5-22
23-25
26-28
29-30
31
Pae 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the ede
to help distinuish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A RIGHT END (1)
B LEFT END (1)
C SLIDING SHELF UPRIGHT(2)
D TOP (1)
E BOTTOM (1)
F BACK (1)
G SLIDING SHELF (1)
H SHELF (1)
I RIGHT FRONT/LEFT REAR LEG (2)
J LEFT FRONT/RIGHT REAR LEG (2)
K SHELF MOLDING (1)
L SIDE SKIRT (2)
M DOOR (2)
N FRONT/BACK SKIRT (2)
O REAR BRACE (1)
A
B
C
C
D
E
F
G
H
I
I
J
J
K
L
L
M
M
N
N
O
Pae 3

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
BLACK 9/16" PAN HEAD SCREW - 4
51S
METAL BRACKET - 6
4G
BLACK 9/16" LARGE HEAD SCREW - 16
1S
BLACK 7/8" FLAT HEAD SCREW - 10
31S
WASHER - 2
9I
BLACK 1-7/8" FLAT HEAD SCREW - 6
2S
3S GOLD 5/16" FLAT HEAD SCREW - 8
METAL PIN - 2
1R
MAGNETIC CATCH - 2
12I
CAM SCREW - 4
8F WOOD DOWEL - 4 15F
NAIL - 44
1N
HIDDEN CAM - 20
1F CAM DOWEL - 16 2F
CAM COVER - 4
50P
PIVOT HINGE- 4
41H
PIVOT HINGE
BRACKET- 2
54G
STRIKE PLATE
BRACKET- 2
14I
GOLD 2-3/4" FLAT HEAD BOLT - 4
109S
Pae 4
(EXTENSION SET SHOWN SEPARATED)
PEXTENSION RAIL - 2 QEXTENSION SLIDE - 2
CROSS SLOTTED DOWEL - 4
28F

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratchin your unit or the floor.
å Push twenty HIDDEN CAMS (1F) into the ENDS (A and
B) SLIDE SHELF (G), SHELF (H), LEGS (I and J) and
FRONT/BACK SKIRTS (N). Then, insert the metal end of a
CAM DOWEL (2F) into each HIDDEN CAM, except in the
FRONT/BACK SKIRTS (N).
Pae 5
Arrow
1F
2F
Arrow
1F
2F
(20 used)
(16 used)
Arrow
1F
2F
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
Do not tihten the HIDDEN CAMS in this step.
Do not insert CAM DOWELS into these parts.
A
B
G
H
I
I
J
J
N
N

å Turn four CAM SCREWS (8F) into the LEGS (I and J).
Step 2
Pae 6
8F
J
J
I
I
Remember:
Rihty tihty.
Lefty loosey.

Step 3
Pae 7
å Separate the EXTENSION SLIDES (Q) from the
EXTENSION RAILS (P) as shown in the upper diaram.
Be prepared, the parts are reasy.
å Fasten the EXTENSION RAILS (P) to the ENDS (A and B).
Use four GOLD 5/16” FLAT HEAD SCREWS (3S).
å NOTE: For each EXTENSION RAIL, turn a SCREW into
the hole shown in the enlared diaram. Then, slide the
innercartride of the EXTENSION RAIL in to find the other
hole that lines up with the hole in the END. Turn a SCREW
into this hole.
Open end
Open end
Push the black lever in and pull the SLIDE from the RAIL.
GOLD 5/16" FLAT HEAD SCREW
(4 used in this step)
3S
P
P
P
Q
A
B
Use this hole.

å Fasten six METAL BRACKETS (4G) to the FRONT/BACK
SKIRTS (N) and SHELF UPRIGHTS (C). Use six BLACK
9/16" LARGE HEAD SCREWS (1S).
å NOTE: Be sure the BRACKETS are even with the edes
of the SKIRTS and UPRIGHTS.
Step 4
Pae 8
BLACK 9/16" LARGE HEAD SCREW
(6 used in this step)
1S
4G
N
N
C
C

å Fasten a RIGHT FRONT/LEFT REAR LEG (I) and a LEFT
FRONT/RIGHT REAR LEG (J) to a FRONT/BACK SKIRT (N).
å Repeat this step for the remainin LEGS (I and J)
and SKIRT (N).
Step 5
Pae 9
N
I
J
Surface with HIDDEN CAMS
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
1
2

å Fasten the LEFT END (B) to the TOP (D). Tihten two HIDDEN CAMS.
Step 6
Pae 10
Start Tighten
Arrow
Minimum
190 derees
Caution
Risk of damae or
injury. HIDDEN CAMS
must be completely
tihtened. HIDDEN
CAMS that are not
completely tihtened
may loosen, and parts
may separate. To
completely tihten:
Arrow
Maximum
210 derees
These two small
holes must be here.
These holes must be here.
B
D