Teknik Hudson 5425829 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Hudson 4-Drawer Chest
Model 5425829
You won't lose your
shirt with this one.
Teknik
www.teknikoffice.co.uk

Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Table of Contents Assembly Tools Required
3
4
5-21
22-24
25-28
29-30
31
Page 2
Electric drill with 1/8" bit
(ONLY in indicated step)

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A LEFT END (1)
B RIGHT END (1)
C TOP (1)
D BOTTOM (1)
E SKIRT (1)
F BRACE (1)
G DRAWER FRONT (3)
H LEFT DRAWER SIDE (4) - 1 with label
J DRAWER BACK (4)
K DRAWER BOTTOM (4)
L DRAWER BRACE (4)
M DRAWER FRONT MOLDING (4)
N UPPER BACK (1)
O CENTER BACK (1)
P LOWER BACK (1)
Q BALLAST (1)
R WHITE DRAWER FRONT (1)
S RIGHT DRAWER SIDE (4)
Page 3
A
B
C
D
E
F
G
H
JK
L
M
N
O
P
Q
R
S
G
H
H
G
H
J
K
S

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
Page 4
35AA UNIVERSAL CABINET RAIL - 8 35AC DRAWER RIGHT - 4 35AD DRAWER LEFT - 4
FURNITURE TIPPING
RESTRAINT KIT - 1
98
SILVER 1-1/2" FLAT HEAD SCREW - 20
7SILVER 1-1/8" FLAT HEAD SCREW - 4 8
SMALL WOOD
DOWEL - 40
5
LARGE WOOD
DOWEL - 38
4
BLACK 3/8" FLAT HEAD SCREW - 32
10
BLACK 3/4" FLAT HEAD SCREW - 12
9
APPLIQUE
CARD - 2
6
CAM SCREW - 37
3
LARGE HIDDEN
CAM - 17
1SMALL HIDDEN
CAM - 20
2
SILVER 2" FLAT HEAD SCREW - 2
11

Step 1
Page 5
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Fasten the UNIVERSAL CABINET RAILS* (35AA) to the
ENDS (A and B). Use sixteen BLACK 3/8" FLAT HEAD
SCREWS (10) through holes #1 and #3.
å *patent pending glide system
A
B
3
2
1
1
2
3
BLACK 3/8" FLAT HEAD SCREW
(16 used for the RAILS)
10
Edge with
more holes
These holes
must be here.
These holes
must be here.
Glide end
3
2
13
2
13
2
1
1
2
31
2
31
2
3
Glide end
VIEW THE DRAWER GLIDE VIDEO

Hardware Usage Guide
HOW TO USE A HIDDEN CAM & CAM SCREW OR CAM DOWEL
NOTE: Various CAM SCREWS or a CAM DOWEL may be used.
Cam Screws Cam Dowel
Turn the CAM SCREW or
gently tap the CAM DOWEL
until the shoulder is against
the surface of the part.
1.
Hidden CamHidden Cam
Arrow
Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the
edge of the board.
Hole
2.
3.
1
2
Insert the CAM SCREW or CAM DOWEL into the
HIDDEN CAM. Tighten the HIDDEN CAM.
Page 6

å Push four LARGE HIDDEN CAMS (1) into the ENDS (A and B).
å Turn twelve CAM SCREWS (3) into the exact holes shown in
the ENDS (A and B).
å Then, insert twenty-two LARGE WOOD DOWELS (4) into the
remaining holes in the ENDS (A and B).
Step 2
A
B
Page 7
4
(22 used)
Some assembly
(and snacks) required.
Arrow
3
3
1

å Push one LARGE HIDDEN CAM (1) into the LOWER BACK (P) as shown.
å Turn one CAM SCREW (3) into the BOTTOM (D).
å Insert two LARGE WOOD DOWELS (4) into the BOTTOM (D).
å Fasten the LOWER BACK (P) to the BOTTOM (D). Tighten one HIDDEN CAM.
å NOTE: Be sure the WOOD DOWELS in the BOTTOM insert into the LOWER BACK.
å Insert two LARGE WOOD DOWELS (4) into the BOTTOM (D), and fasten the SKIRT (E) to the BOTTOM (D). Use two
SILVER 2" FLAT HEAD SCREWS (11).
Step 3
Page 8
D
P
4
4
D
PE
These holes must be here.
Surface with
fewer holes
Arrow
1
3
SILVER 2" FLAT HEAD SCREW
(2 used for the SKIRT)
11

å Insert six LARGE WOOD DOWELS (4) into the long edges of the
CENTER BACK (O).
å Insert the LARGE WOOD DOWELS in the CENTER BACK (O) into
the BACKS (N and P) so the BACKS are all connected.
Step 4
Page 9
4
P
O
N
Surface with holes
Surface with holes
Notch
(6 used)

å Push five LARGE HIDDEN CAMS (1) into the BOTTOM (D)
and BACKS (N, O, and P).
å Fasten the RIGHT END (B) to the BOTTOM (D) and
BACKS (N, O, and P). Tighten five HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the RIGHT END insert
into the BOTTOM (D), SKIRT (E), and BACKS (N, O, and P).
Step 5
Page 10
E
P
O
N
D
B
Arrow
Arrow
1
1