Teknik Essentials L-Shaped Desk 5425092 User manual

Essentials L-Shaped Desk
Model 5425092
For all your
newfangled gadgetry.
Teknik
www.teknikoffice.co.uk

Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
Table of Contents Assembly Tools Required
3
4
5-26
27-31
32-36
37-38
39
Page 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A LARGE TOP (1)
B SMALL TOP (1)
C LEFT END (1)
D LEFT UPRIGHT (1)
E RIGHT UPRIGHT (1)
F RIGHT END (1)
G MOLDING (1)
H SMALL MODESTY PANEL (1)
J FIXED SHELF (2)
K SKIRT (1)
L DRAWER FRONT (1)
M LEFT DRAWER SIDE (1)
N RIGHT DRAWER SIDE (1)
O DRAWER BACK (1)
P DRAWER BOTTOM (1)
Q BACK (1)
R LARGE MODESTY PANEL (1)
A
B
C
D
E
F
G
H
J
J
KL
M
N
O
P
Q
R
Page 3

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
CAM SCREW - 12
5
LARGE HIDDEN
CAM - 8
3SMALL HIDDEN
CAM - 4
4
(EXTENSION SET SHOWN SEPARATED)
EXTENSION SLIDE - 2
2
EXTENSION RAIL - 2
1
WOOD DOWEL - 30
6PULL - 1 7
APPLIQUE CARD - 2
8NAIL - 18 9
GOLD 1-3/4" FLAT HEAD SCREW - 18
14 GOLD 1-1/4" FLAT HEAD SCREW - 4 15
SILVER 15/16" PAN HEAD SCREW - 2
16 GOLD 1/2" FLAT HEAD SCREW - 22 17
METAL PLATE - 1
10
TIE PLATE - 1
11 BRACKET - 4
12 FILE BAR - 2
13
Page 4 www.sauder.com/service 425092

Step 1
Page 5
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Separate the EXTENSION SLIDES (2) from the
EXTENSION RAILS (1) as shown in diagram 1. Be
prepared, the parts are greasy.
å Fasten the EXTENSION RAILS (1) to the LEFT END (C),
and LEFT UPRIGHT (D). Use eight GOLD 1/2" FLAT HEAD
SCREWS (17) through the holes shown in diagram 2.
å NOTE: The EXTENSION SLIDES will be used later for
the DRAWERS.
C
D
Open end
Open end
Push the black lever up and pull the SLIDE from the RAIL.
Open end
1
1
2
1
2
1
GOLD 1/2" FLAT HEAD SCREW
(8 used in this step)
17
1

Hardware Usage Guide
HOW TO USE A HIDDEN CAM & CAM SCREW OR CAM DOWEL
NOTE: Various CAM SCREWS or a CAM DOWEL may be used.
Cam Screws Cam Dowel
Turn the CAM SCREW or
gently tap the CAM DOWEL
until the shoulder is against
the surface of the part.
1.
Hidden CamHidden Cam
Arrow
Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the
edge of the board.
Hole
2.
3.
1
2
Insert the CAM SCREW or CAM DOWEL into the
HIDDEN CAM. Tighten the HIDDEN CAM.
Page 6

Step 2
å Push four LARGE HIDDEN CAMS (3) into the large holes
in the LEFT END (C) and LEFT UPRIGHT (D).
3
C
D
3
Page 7

å Insert twelve WOOD DOWELS (6) into the
FIXED SHELVES (J) and SKIRT (K).
Step 3
J
J
K
6
(12 used)
Page 8
Just think. The sooner
you do this, the sooner
you do something else.

å Fasten the FIXED SHELVES (J) and SKIRT (K) to the
LEFT UPRIGHT (D). Use four GOLD 1-3/4" FLAT
HEAD SCREWS (14).
å NOTE: Be sure the WOOD DOWELS in the SHELVES and
SKIRT insert into the UPRIGHT.
Step 4
D
J
J
K
Open end
GOLD 1- 3/4" FLAT HEAD SCREW
(4 used in this step)
14
Page 9

å Fasten the LEFT END (C) to the FIXED SHELVES (J)
and SKIRT (K). Use four GOLD 1-3/4" FLAT
HEAD SCREWS (14).
å NOTE: Be sure the WOOD DOWELS in the SHELVES and
SKIRT insert into the UPRIGHT.
Step 5
J
J
K
C
Open end
GOLD 1- 3/4" FLAT HEAD SCREW
(4 used in this step)
14
Page 10 www.sauder.com/service 425092