Teknik Spanish Style Desk 5420114 User manual

www.teknikoffice.co.uk
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
The oriinal desktop.
Spanish Style Desk
Model 5420114
Teknik

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
3
4-5
6-32
Pae 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the ede
to help distinuish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A RIGHT END (1)
B LEFT END (1)
C TOP (1)
D TOP SKIRT (1)
D20 DRAWER RIGHT SIDE (2)
D21 DRAWER LEFT SIDE (2)
D28 FILE DRAWER RIGHT SIDE (1)
D29 FILE DRAWER LEFT SIDE (1)
D74 DRAWER BACK (1)
D78 FILE DRAWER BACK (1)
D513 PENCIL DRAWER BACK (1)
D707 FILE DRAWER BOTTOM (1)
D716 SMALL DRAWER BOTTOM (1)
D982 LARGE DRAWER BOTTOM (1)
E UPRIGHT (1)
F MODESTY PANEL (1)
GRIGHT FRONT/LEFT REAR
PEDESTAL LEG (2)
HLEFT FRONT/RIGHT REAR
PEDESTAL LEG (2)
I LEFT FRONT LEG (1)
J LEFT REAR LEG (1)
K BRACE (2)
L BOTTOM (1)
M DRAWER FRONT (1)
M67 DRAWER BRACE (1)
N FILE DRAWER FRONT (1)
O PENCIL DRAWER FRONT (1)
P EXTENSION BLOCK (1)
Q BACK (1)
A
B
C
D
D20
D20
D21
D74
D78 D28
D29
D21
D513
D707
D716
D982
E
F
G
G
H
H
I
J
K
K
L
M
N
O
P
Q
M67
Pae 3

Hardware Identification
(EXTENSION SET SHOWN SEPARATED)
REXTENSION RAIL - 2 SEXTENSION SLIDE - 2
35GA CABINET RIGHT - 1 35GB CABINET LEFT - 1 35GC DRAWER RIGHT - 1
40CA CABINET RIGHT - 1 40CB CABINET LEFT - 1 40CC DRAWER RIGHT - 1
FILE GLIDE - 2
15B
35GD DRAWER LEFT - 1
40CD DRAWER LEFT - 1
10A SLIDE CAM - 6 CAM SCREW - 18 8F
WOOD DOWEL - 14
15F NAIL - 20 1N
HIDDEN CAM - 34
1F CAM DOWEL - 16 2F
KNOB - 3
71K CAM COVER - 12
50P
BACKPLATE - 3
147K
Pae 4

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
GOLD 1" MACHINE SCREW - 3
50S
BLACK 1-7/8" FLAT HEAD SCREW - 3
2S
BROWN 1-1/2" FLAT HEAD SCREW - 2
14S
3S GOLD 5/16" FLAT HEAD SCREW - 24
BLACK 1-15/16" FLAT HEAD SCREW - 2
113S
30S BLACK 1-9/16" FLAT HEAD SCREW - 13
Pae 5

Step 1
Arrow
1F
2F
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratchin your unit or the floor.
å Push sixteen HIDDEN CAMS (1F) into the ENDS (A and B),
UPRIGHT (E), MODESTY PANEL (F), BRACES (K) and
DRAWER BRACE (M67). Then, insert the metal end of a
CAM DOWEL (2F) into each HIDDEN CAM.
Step 1
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
Do not tihten the HIDDEN CAMS in this step.
Arrow
1F
2F
Arrow
1F
2F
(16 used)
A
B
E
F
K
K
M67
Pae 6

Step 2
A
B
E
å Push eihteen HIDDEN CAMS (1F) into the
remainin holes of the ENDS (A and B) and
UPRIGHT (E) and BOTTOM (L).
1F
Arrow
(18 used)
Arrow
Arrow
1F
1F
Hole
Arrow
The arrow in the HIDDEN
CAM must point toward the
hole in the ede of the board.
L
Pae 7

Step 3
G
G
H
H
I
J
8F
å Turn eihteen CAM SCREWS (8F) into the LEGS (G, H, I, and J).
(18 used)
Pae 8

å Push three WOOD DOWELS (15F) into the LEFT REAR LEG (J).
å Fasten the LEFT REAR LEG (J) to LEFT END (B). Tihten
three HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS insert into the LEFT END.
å Push three WOOD DOWELS (15F) into the LEFT FRONT LEG (I)
.
å Fasten the LEFT FRONT LEG (I) to LEFT END (B). Tihten
three HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS insert into the LEFT END.
Step 4
J
I
B
15F
15F
Surface with HIDDEN CAMS
Ede with CAM DOWELS
1
2
These edes
should be even.
These edes
should be even.
Pae 9

Step 5
Pae 10
å Push a WOOD DOWEL (15F) into a
LEFT FRONT/RIGHT
REAR PEDESTAL LEG (H) .
å Fasten the LEFT FRONT/RIGHT REAR PEDESTAL LEG (H)
to the RIGHT END (A). Tihten two HIDDEN CAMS.
15F
Surface with HIDDEN CAMS
A
H
These edes
should be even.
Ede with CAM DOWELS
1
2
Just think. The sooner
you do this, the sooner
you do somethin else.

Step 6
Pae 11
å Push a WOOD DOWEL (15F) into a
RIGHT FRONT/LEFT
REAR PEDESTAL LEG (G) .
å Fasten a RIGHT FRONT/LEFT REAR PEDESTAL LEG (G)
to the UPRIGHT (E). Tihten two HIDDEN CAMS.
15F
Surface with HIDDEN CAMS
E
G
These edes
should be even.
Ede with CAM DOWELS
1
2

Step 7
Pae 12
å Separate the EXTENSION SLIDES (S) from the
EXTENSION RAILS (R) as shown in the upper diaram.
Be prepared, the parts are reasy.
å Fasten the EXTENSION RAILS (R) to the RIGHT END (A)
and UPRIGHT (E). Use four GOLD 5/16” FLAT HEAD
SCREWS (3S) throuh holes #1 and #3.
å NOTE: The EXTENSION SLIDES will be used later for
the DRAWERS.
Push the black lever in and pull the SLIDE from the RAIL.
R
S
1
1
1
3
3
3
4
4
4
2
2
2
GOLD 5/16" FLAT HEAD SCREW
(4 used in this step)
3S
R
R
A
Open end
Open end
E

Step 8
Pae 13
A
E
GOLD 5/16" FLAT HEAD SCREW
(4 used in this step)
3S
Roller end
Roller end
å Fasten the CABINET RIGHT (40CA) to the RIGHT END (A) and
CABINET LEFT (40CB) to the UPRIGHT (E). Use four GOLD
5/16" FLAT HEAD SCREWS (3S) throuh holes #1 and #3.
1
1
2
2
3
3
4
4

Step 9
Pae 14
E
å Flip the UPRIGHT (E) over.
å Fasten the EXTENSION BLOCK (P) to the UPRIGHT (E).
Use two BROWN 1-1/2" FLAT HEAD SCREWS (14S).
Finished ede
BROWN 1-1/2" FLAT HEAD SCREW
(2 used in this step)
14S
P

Step 10
Pae 15
å Fasten the CABINET RIGHT (35GA) to the EXTENSION
BLOCK (P) and the CABINET LEFT (35GB) to the LEFT
END (B). Use four GOLD 5/16" FLAT HEAD SCREWS (3S)
throuh holes #1 and #3.
1
1
2
2
3
3
Roller end
Roller end
GOLD 5/16" FLAT HEAD SCREW
(4 used in this step)
3S
P
B

Step 11
Pae 16
å Fasten the MODESTY PANEL (F) to the LEFT END (B).
Tihten three HIDDEN CAMS.
Start Tighten
Arrow
Minimum
190 derees
Caution
Risk of damae or
injury. HIDDEN CAMS
must be completely
tihtened. HIDDEN
CAMS that are not
completely tihtened
may loosen, and parts
may separate. To
completely tihten:
Arrow
Maximum
210 derees
B
F
Surface with HIDDEN CAMS
Surface with HIDDEN CAMS
Do not stand the unit upriht without the
BACK fastened. The unit may collapse.
Caution

Step 12
Pae 17
å Fasten the LEFT END (B) and MODESTY PANEL (F) to the
TOP (C). Tihten four HIDDEN CAMS.
Arrow
Minimum
190 derees
Maximum
210 derees
Surface with holes
C
B
F

Step 13
Pae 18
å Push four WOOD DOWELS (15F) into the holes in the
short edes of the BRACES (K).
å Fasten the BRACES (K) to the RIGHT END (A). Tihten
two HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS insert into the holes
in the UPRIGHT.
å NOTE: Be sure the BRACES (K) are positioned exactly as shown.
Surface with HIDDEN CAMS
Surface with HIDDEN CAMS
K
K
Surface with
HIDDEN CAMS
This CAM SCREW
must be here.
A
These edes
should be even.
This HIDDEN CAM must be here.
Arrow
Minimum
190 derees
Maximum
210 derees
15F
15F

Step 14
Pae 19
å Fasten the UPRIGHT (E) to the BRACES (K). Tihten two
HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS insert into the holes
in the LEFT END.
K
K
Surface without
HIDDEN CAMS
This CAM SCREW
must be here.
E
Arrow
Minimum
190 derees
Maximum
210 derees

Step 15
Pae 20
å Fasten the BOTTOM (L) to the REAR LEGS (G and H).
Tihten two HIDDEN CAMS.
å NOTE: Be sure the notches in the BOTTOM wrap around
the LEGS.
Arrow
Minimum
190 derees
Maximum
210 derees
H
G
L
Surface with HIDDEN CAMS
Notch