teko Astra-621 User manual

Astra-621
Motion + Glass break
detector
User guide
Manufacturer:
ZAO NTC TEKO
420108 Kazan, Russia
Gafuri 71
[phone]
[email protected]
www.teko.biz
Made in Russia
rev. 621-v2_2_instr_en
1 FUNCTION
The detector is intended for detection of
unauthorized access into an enclosed area,
detection of glass breaking of glazed
constructions of an enclosed area and
generation of an alarm notification by opening
contacts of dedicated alarm relay.
2 DETECTION ZONES
3 SPECIFICATIONS
Detectable moving speed, m/sec ............0.3 to 3.0
Supply voltage, V........................................9 to 15
Current consumption, mA...................................15
Overall dimensions, mm.........................92×64×45
Operation conditions
Temperatures, °С.................................- 20 to + 55
Relative air humidity, % .................up to 98 at + 25 °С
without moisture condensation
4DELIVERY SET
Bracket –1 pc., dowel - 2 pcs., screw - 2 pcs., label –
2 pcs.
5 INFORMATIVITY
In the factory setting, indication of notifications
Alarm, Power failure is enabled permanently, indi-
cation of other notifications is enabled for 24 hours
after the detector is powered on.
Alarm mode of notifications is changed by closing
the contact Ind after the detector enters the
standby mode, for which close the contact Ind for
at least 10 sec. until the indicator turns on:
- 1x flash - indication is allowed,
- 2x flash –indication disabled (Alarm notifications
are disabled immediately after changing the mode,
notifications are generated only by opening the
alarm relay of the detector).
ATTENTION! When the detector's power supply
is reset, the factory setting of the indication
mode is automatically restored.
Notification
Indication
Relay
PIR
GB
Boot time
Flashes1timeper
1 sec after power
on. Duration up to
60sec
Up to
60 sec
Up to
60 sec
Norm
Off
PIR-Alarm
Movement in
the detection
zone
for
4 sec
GB-Alarm
Glass break-
ing in the
detection
zone
for
4 sec
PIR + GB
Alarm
Movement
and glass
for
4 sec
for
4 sec

Notification
Indication
Relay
PIR
GB
breaking in
the detection
zone
High
frequency
interference
2 flashes with
a period 0.6
sec when
exposed to
interference
Low
frequency
interference
1 flash with a
period 0.6 sec
when exposed
to interference
Low supply
voltage
On when
supply volt-
age lower
than 8.4 V
Tampering
Off
ТМР
« » –relayis closed, « » –relayis
open, –indicator on, ТМР –ТМР circuit
is open
6 INSTALLATION PLACE
1) Recommended installation height is 2.3-
2.5 m and at a distance not more than 6m from
the most distant spot of protected glass.
2) The detector cannot be used in premises
with high level of acoustic interference.
3) Alarm loop and power supply wires should
be located far from power cables.
To eliminate false alarm hazards
1) It is recommended to close all doors, air-
vents, switch off possible sourses of intense air
flows (fans, air-conditioners) and acoustic inter-
ferences (loudspeakers, etc.) in the room during
protection period.
2) The detector's location should provide di-
rect visibility of all secured glass parts; masking
the detector with decorative curtains is not al-
lowed, as sensitivity may be lost.
Not recommended installation places
7INSTALLATION ORDER
1) Open the detector by pushing the cover latch
out of the base slot. Remove cover.
2) Fasten the bracket.
3) Press out the plug of
the selected wire entry
hole in the detector base.
4) Route the wires from the
power supply and the alarm
loop through the wire entry
hole.
5) Mount the detector on the
bracket.
Orient the base of the
detector strictly according
to the figure!
It is possible to install using a ball bracket
(supplied separately).
6) Fix the connected wires in the detector termi-
nals:
ТМР –tampering control terminals;
RelayPIR, RelayGB –loopterminals;
+12V, GND–powersupplyloopterminals.
7) Replace the detector cover (until it clicks).
8) Perform GB and PIR channels testing (see p.
9).
9 TESTING
GB-channel:
1) Turn on the power of the detector. The
indicator flashes for a maximum of 60 seconds.
2) During this time, briefly (for 1-2 sec) close the
contact Ind. The GB test mode will turn on for 8
minutes.
3) Close the cover.
4) Using a glass break simulator, check the detector
operation for glass break simulation, high-frequency
and low-frequency interference (see table).
Note –It is recommended to use glassbreak simula-
tors of Honeywell brands: FG-701 Glassbreak Simula-
tor, Argus-Spektr: ARS Acoustic Glass Break Simula-
tor, DSCTM: AFT-100 Glassbreak Simulator operat-
ing in “plate” mode.
PIR-channel:
After the end of the GB-channel
testing mode (8 min), perform a
TEST pass.
Moving through the detection zone
at a speed of 0.3 m/sec and 3
m/sec, determine the sensitivity
zones by turning on the indicator
(“PIR Alarm” notification).
10 WARRANTY
The operation warranty period is 5 years from
the date of operation start-up but no longer than
5 years 6 months from the date of manufactur-
ing subject to the requirements of the User
guide.