TMG TMG-DT3081 User manual

►www.tmgindustrial.com 0/23 TOLL FREE:1-877-761-2819

►www.tmgindustrial.com 1/23 TOLL FREE:1-877-761-2819
MAIN SPECIFICATIONS :
Assembly size : W9.15 x L24 x H6 (m) / 30 x 78.7 x 19.7 (ft)
Ridge height : 6m / 19.7 ft
Peak clearance : 5.4m / 17.7 ft
Front and back door : 4.27 x 3.96 (m) / 14 x 13 (ft)
Shoulder height : 3.6 m / 11.8 ft
CONCRETE FOUNDATION SIZE SEE BELOW FIGURE.

►www.tmgindustrial.com 2/23 TOLL FREE:1-877-761-2819
PRIOR TO ASSEMBLY
Please read the instructions carefully before installation. It is very important to follow your local safety regulations and
industry standards during installation. Regulations may include but are not limited to:
• Safety helmets, protective eyewear, and clothing
• Safety harnesses for all elevated workers
• Proper ladder, cage, and safety operation
Check all components and parts before installation. All parts are marked with a part number, please refer to the parts list
to ensure you have all parts.
Choose a day with low or no wind to install, it is hard to assemble with heavy wind. Do not make any alterations to the
structure. Do not hang any weight on the frame during installation, including parts. We are not responsible for any
damages or injuries caused by inappropriate installation, unauthorized modifications or extreme weather.
This building is not intended for human occupancy.
It is recommended to use heavy duty duct tapes to tape the tube connection joint spots to protect the cover from damage
and worn. It will help to extend the cover life span.
Check the parts list below to make sure all parts are received prior to assembly.

►www.tmgindustrial.com 3/23 TOLL FREE:1-877-761-2819
FRAME STRUCTURE DIAGRAM.

►www.tmgindustrial.com 4/23 TOLL FREE:1-877-761-2819
TMG-DT3081 PART LIST
PARTS
CODE
GRAPHICAL
DESCRIPTION
LENGTH
QTY
BOX
1
Peak arch tube
(for 7 middle trusses )
L2570mm
7
B
1A
Peak arch tube
(for front and rear truss)
L2570mm
2
B
2
Upper rafter tube
(for middle trusses)
L2921mm
14
A
2A
Upper rafter tube
(for front and rear truss)
L2921mm
4
A
3
Shoulder tube
(for middle trusses)
L1757mm
14
B
3A
Shoulder tube
(front and rear trusses)
L1757mm
4
B
4
Sidewall tube
(middle trusses)
L2878mm
14
A
4A
Sidewall tube
(front and rear left truss)
L2878mm
2
A
4B
Sidewall tube
(front and rear right truss)
L2878mm
2
A
5
Roof purlin
(horizontal tube)
L3040mm
72
A
5L
Baseplate for front and rear
truss left corners
W260xL520mm
2
B
5R
Baseplate for front and rear
truss right corners
W260xL520mm
2
B

►www.tmgindustrial.com 5/23 TOLL FREE:1-877-761-2819
6L
Left baseplate of front and
rear door frame
W150xL200mm
2
B
6R
Right baseplate of front and
rear door frame
W150xL200mm
2
B
7
Baseplates for middle truss
W260xL480mm
14
B
7A
Ratchets
3T
46
B
7B
Expansion bolts
φ16x150mm
80
B
8
Ceiling cross bar
(front and rear truss)
L2083mm
2
B
9
Ceiling cross bar
(front and rear truss)
L2233mm
2
B
9L
Front and rear vertical door
rail
(left side upper part)
L1984mm
2
B
9R
Front and rear vertical door
rail
(right side upper part)
L1984mm
2
B
10
Door center vertical
supporting rod for cross
beam
(front and rear truss)
L1018mm
2
B
10L
Front and rear vertical door
rail (left side lower part)
L2625mm
2
B
10R
Front and rear vertical door
rail (right side lower part)
L2625mm
2
B
11
Door frame horizontal tube
(front and rear truss)
L1982mm
8
B
12
Bottom tension bar
(front and rear truss)
L1970mm
4
B

►www.tmgindustrial.com 6/23 TOLL FREE:1-877-761-2819
13
Front and rear door hand
winch crossing tube
L1984mm
2
B
14
Top cover tension tube
L1993mm
24
A
14A
Top cover tension tube
L900mm
2
A
15
Front and rear roll up door
dropping tubes (to connect
#16)
L2195mm
14
A
16
Front and rear roll up door
dropping tubes (to connect
#15)
L2192mm
14
B
17
Sidewall frame steel tension
cables
φ6xL4290mm
20
B
18
Ridge steel tension cables
(front and rear trusses)
φ6xL3070mm
24
B
19
Middle truss crossing steel
tension cables
φ6xL3990mm
7
B
20
Front and rear truss left and
right steel cables
φ6xL3900mm
4
B
21
Tie down straps
(for #7A)
W38xL800mm
46
B
22
Cable connection plate
L91mm
34
B
22A
Pressing plate
W20xL2000mm
8
B
23
Roll up door hand winch
1200LB
2
B
23A
Wire rope for front and rear
door hand winch
φ4x15m
2
B
23B
Right pulley system for front
and rear doors
L150mm
2
B
23C
Left pulley system for front
and rear doors
L150mm
2
B
24
Front and rear vertical door
rail connection plate
L240mm
4
B

►www.tmgindustrial.com 7/23 TOLL FREE:1-877-761-2819
24A
Front and rear vertical door
rail end plate (floatable to
keep door rail straight)
L220mm
4
B
25
Tension tube end water plug
φ32mm
12
B
26
Tube clamps
φ48mm
6
B
27
Tapping screw
#12x25mm
64
B
28
Self locking bolt
and nuts
M10x70mm
81
B
29
Strengthened bolt
and nuts
M12x30mm
288
B
30
Hex boltand nuts
M10x50mm
14
B
31
Hex bolt and nuts
M10x70mm
60
B
32
Braided rope
L160m
1
B
33
Roof fabric tarp cover
W18.4xL24.6m
1
B
34
Front and rear truss cover
panel
W6.2xL9.1m
2
B
35
Front and rear roll up door
cover panel
W4.2xL4.6m
2
B
36
Front and rear fabric tarp
secure pin
L200mm
2
B
37
Plastic hose (in grooves at
both ends of #33)
φ25xL4m
10
B
37A
Connector
(for connection #37)
φ25mm
8
B
38
Scratch resistant tape
L10m
4
B

►www.tmgindustrial.com 8/23 TOLL FREE:1-877-761-2819
STEP 1 : BASEPLATE POSITIONING AND INSTALLATION.
Installation diagram of expansion bolt.
PARTS
CODE
PART
QTY
PARTS
CODE
PART
QTY
5L
2
6R
2
5R
2
7
14
6L
2
7B
80

►www.tmgindustrial.com 9/23 TOLL FREE:1-877-761-2819
STEP 2 : ASSEMBLE ALL TRUSSES.
Front and rear trusses.
PARTS
CODE
PART
QTY
PARTS
CODE
PART
QTY
1A
1x2
4A
1x2
2A
2x2
4B
1x2
3A
2x2
29
24x2