TMG TMG-DT2030-PRO User manual

▶W W W . T M G I N D U S T R I A L . C O M P 0/ 3 1 T o l l F r e e : 1 - 877- 7 6 1 - 2 8 1 9

▶W W W . T M G I N D U S T R I A L . C O M P 1 / 3 1 T o l l F r e e : 1 - 877- 7 6 1 - 2 8 1 9
Main Specifications :
Assembly size : W6 x L9.6 x H4.5 (m) / 20 x 31 x 15 (ft)
Ridge height : 4.5m / 15 ft
Front and back door : 3.6 x 2.9 (m) / 12 x 10 (ft)
Shoulder height : 3 m / 10ft
Prior to assembly
Please go through the whole instruction manual completely. It is very important to
follow your local safety regulations and industry standards during installation.
Regulations may include but are not limited to :
- Safety helmets, protective eyewear, and clothing
- Safety harnesses for all elevated workers
- Proper ladder, cage, and safety operation
Check all components and parts before installation. All parts are marked with a part
number, please refer to the parts list to ensure you have all parts.
Choose a day with low or no wind to install, it is hard to assemble with heavy wind.
Do not make any alterations to the structure. Do not hang any weight on the frame
during installation, including parts. We are not responsible for any damages or
injuries caused by inappropriate installation, unauthorized modifications or extreme
weather.
This building is not intended for human occupancy.
It is recommended to use heavy duty duct tapes to tape the tube connection joint spots
to protect the cover from damage and worn. It will help to extend the cover life span.
Check the parts list below to make sure all parts are received prior to assembly.

▶W W W . T M G I N D U S T R I A L . C O M P 2 / 3 1 T o l l F r e e : 1 - 877- 7 6 1 - 2 8 1 9
Frame structure diagram.

▶W W W . T M G I N D U S T R I A L . C O M P 3 / 3 1 T o l l F r e e : 1 - 877- 7 6 1 - 2 8 1 9
TMG-DT2030-PRO Part List
Parts
Code
Graphical
Description
Length (mm)
Qty
1
Peak arch tube
(for middle trusses)
1811
3
1A
Peak arch tube
(for front and rear truss)
1811
2
2
Upper rafter tube
(for middle trusses)
1495
6
2A
Upper rafter tube
(for front and rear truss)
1495
4
3
Shoulder tube
(for middle trusses)
1444
6
3A
Shoulder tube
(front and rear trusses)
1444
4
4
Sidewall tube
(middle trusses)
2163
5
4A
Sidewall tube
(front and rear left truss)
2163
2
4B
Sidewall tube
(rear right truss)
2163
1
4C
Sidewall tube
(front right truss)
2163
1
4D
Sidewall tube
(second right truss)
2163
1
5
Roof purlin
(horizontal tube)
2440
27
5L
Baseplate for front and
rear truss left corners
L320xW260
2
5R
Baseplate for front and
rear truss right corners
L320xW260
2
6L
Left baseplate of front
door frame
L200xW150
2

▶W W W . T M G I N D U S T R I A L . C O M P 4 / 3 1 T o l l F r e e : 1 - 877- 7 6 1 - 2 8 1 9
6R
Right baseplate of front
door frame
L200xW150
2
7
Baseplates for middle
truss
L280xW260
6
7A
Ratchets
155
35
7B
Expansion bolts
φ16x150
52
8
Ceiling cross bar
(front and rear truss)
1748
2
9
Ceiling cross bar
(front and rear truss)
1898
2
9L
Front and rear vertical
door rail
(left side upper part)
1465
2
9R
Front and rear vertical
door rail
(right side upper part)
1465
2
9A
Side door left tube
2027
1
9B
Side door right tube
2027
1
9C
Side door
L2000xW900
1
10
Door center vertical
supporting rod for cross
beam
930
2
10L
Front and rear vertical
door rail
(left side lower part)
2015
2
10R
Front and rear vertical
door rail
(right side lower part)
2015
2
11
Door frame horizontal
tube
(front and rear truss)
940
4
11C
Side door upper tube
2328
1
12
Bottom tension bar
(front and rear truss)
930
4

▶W W W . T M G I N D U S T R I A L . C O M P 5 / 3 1 T o l l F r e e : 1 - 877- 7 6 1 - 2 8 1 9
13
Door hand winch
crossing tube
944
2
14
Top cover tension tube
(for both bottom sides)
1993
7
14A
Top cover tension tube
(for both bottom sides)
1970
2
14B
Top cover tension tube
2450
1
15
Roll up door dropping
tubes (to connect #16)
1856
10
16
Roll up door dropping
tubes (to connect #16)
1859
10
17
Sidewall frame steel
tension cables
3700
10
18
Ridge steel tension
cables
(front and rear trusses)
2800
16
19
Middle truss crossing
steel tension cables
2000
3
20
Front and rear truss left
and right steel cables
3000
4
21
Tie down straps
(for #7A)
800
35
22
Cable connection plate
91
22
22A
Pressing plate
2000
6
22B
Pressing plate
1000
5
23
Roll up door hand winch
2
23A
Wire rope for front and
rear door hand winch
10000
2
23B
Right pulley system for
front and rear doors
150
2
23C
Left pulley system for
front and rear doors
150
2
23D
Clip
6

▶W W W . T M G I N D U S T R I A L . C O M P 6 / 3 1 T o l l F r e e : 1 - 877- 7 6 1 - 2 8 1 9
24
Front and rear vertical
door rail connection
plate
L240xW134
4
24A
Front and rear vertical
door rail end plate
(floatable to keep door
rail straight)
220
4
25
Tension tube end water
plug
(φ32)
14
26
Tube clamps
(φ48)
6
27
Plastic hose (in grooves
at both ends of #33)
4000
7
27A
Connector
(for connection #27)
(φ25)
6
28
Self locking bolt and
nuts
M10x70
34
29
Strengthened bolt and
nuts
M12x30
100
30
Hex bolt and nuts
M10x50
10
31
Hex bolt and nuts
M10x70
50
32
Braided rope
(tie to front and back
doors)
100m
1
33
Roof fabric tarp cover
L13320xW10180
1
34
Front and rear truss
cover panel
L6000xW4700
2
35
Front and rear roll up
door cover panel
L3550xW3460
2
36
Front and rear fabric tarp
secure pin
200
2
37
Tapping screw
#12x25
76
38
Scratch resistant tape
10m
2

▶W W W . T M G I N D U S T R I A L . C O M P 7 / 3 1 T o l l F r e e : 1 - 877- 7 6 1 - 2 8 1 9
Step 1 : Baseplate positioning and installation.
No.
Part
Qty
No.
Part
Qty
5L
2
6R
2
5R
2
7
6
6L
2
7B
48

▶W W W . T M G I N D U S T R I A L . C O M P 8 / 3 1 T o l l F r e e : 1 - 877- 7 6 1 - 2 8 1 9
Step 2 :Assemble all trusses.
 Front truss.
No.
Part
Qty
No.
Part
Qty
1A
1
4A
1
2A
2
4C
1
3A
2
29
12

▶W W W . T M G I N D U S T R I A L . C O M P 9 / 3 1 T o l l F r e e : 1 - 877- 7 6 1 - 2 8 1 9
 Second truss.
No.
Part
Qty
No.
Part
Qty
1
1
4
1
2
2
4D
1
3
2
29
12

▶W W W . T M G I ND U S T R I A L .C O M P 10/ 3 1 T o l l F r e e : 1 - 877-761- 2 8 1 9
 Rear truss.
No.
Part
Qty
No.
Part
Qty
1A
1
4A
1
2A
2
4B
1
3A
2
29
12

▶W W W . T M G I ND U S T R I A L .C O M P 11/ 3 1 T o l l F r e e : 1 - 877-761- 2 8 1 9
 The rest of the trusses. (2 trusses)
No.
Part
Qty
No.
Part
Qty
1
1x2
4
2x2
2
2x2
29
12x2
3
2x2

▶W W W . T M G I ND U S T R I A L .C O M P 12/ 3 1 T o l l F r e e : 1 - 877-761- 2 8 1 9
 Lay down all (5) trusses on the ground when the assembly is all
completed and before moving to next step, and then wrap (#38) around
the sharp points of the joint to avoid friction between the fabric and the
interface, resulting in fabric damage.
No.
Part
Qty
38
2

▶W W W . T M G I ND U S T R I A L .C O M P 13/ 3 1 T o l l F r e e : 1 - 877-761- 2 8 1 9
Step 3 : Put up the front truss.
 Put up the front truss: use a crane is the best and safest way, otherwise
pull with ropes is another option, but you have to make sure it is safe, and
you have enough manpower. We recommend 4 to 6 people to pull the
truss up from different directions. When the truss is up, tie the ropes to the
heavy objects to make sure the truss will stay upright steady, and use bolt
(#29) to connect the truss to the base plate.
No.
Part
Qty
29
8

▶W W W . T M G I ND U S T R I A L .C O M P 14/ 3 1 T o l l F r e e : 1 - 877-761- 2 8 1 9
Step 4 : Put up the rest trusses.
 Refer to step 3 to put up the rest trusses, connect all purlins (#5) with bolt
(#28) and secure all bolts firmly on each span before going to next truss .
No.
Part
Qty
No.
Part
Qty
5
6
29
8
28
12

▶W W W . T M G I ND U S T R I A L .C O M P 15/ 3 1 T o l l F r e e : 1 - 877-761- 2 8 1 9
 Repeat above step to put up all other trusses (from 3rd to 5th truss), and
connect all purlins.
No.
Part
Qty
No.
Part
Qty
5
21
29
24
28
22

▶W W W . T M G I ND U S T R I A L .C O M P 16/ 3 1 T o l l F r e e : 1 - 877-761- 2 8 1 9
 Install the side door frame.
No.
Part
Qty
No.
Part
Qty
7B
4
11C
1
9A
1
31
6
9B
1

▶W W W . T M G I ND U S T R I A L .C O M P 17/ 3 1 T o l l F r e e : 1 - 877-761- 2 8 1 9
 Install the side door.
No.
Part
Qty
9C
1
37
8
Align the lock cylinder
boss with the hole.

▶W W W . T M G I ND U S T R I A L .C O M P 18/ 3 1 T o l l F r e e : 1 - 877-761- 2 8 1 9
 Tension cable installation . All cables are diagonally installed on each
side of the interval.
No.
Part
Qty
No.
Part
Qty
17
10
19
3
18
16
22
22

▶W W W . T M G I ND U S T R I A L .C O M P 19/ 3 1 T o l l F r e e : 1 - 877-761- 2 8 1 9
Step 5 : Front and rear trusses to complete. (2 trusses)
No.
Part
Qty
No.
Part
Qty
8
1x2
20
2x2
9
1x2
23B
1x2
9L
1x2
23C
1x2
9R
1x2
24
2x2
10L
1x2
24A
2x2
10R
1x2
25
4x2
10
1x2
26
3x2
11
2x2
30
5x2
12
2x2
31
20x2
13
1x2