TMG TMG-ST2041V User manual

▶W W W . T M G I N D U S T R I A L . C O M P 0 / 19 T o l l F r e e : 1 - 877-761-2819

▶W W W . T M G I N D U S T R I A L . C O M P 1 / 19 T o l l F r e e : 1 - 877-761-2819
Main Specifications :
-Overall assembled size : W6 x L12 x H3.65 (m) / 19.68 x 39.37 x 11.97 (ft)
-Shoulder height : 2 (m) / 6.56 (ft)
-Front and rear roll up door : 3 x 3 (m) / W9.84 x H9.84 (ft)
Prior to assembly
Please read the instructions carefully before installation. It is important to follow your
local safety regulations and industry standards during installation. Regulations may
include but are not limited to :
- Safety helmets, protective eyewear, and clothing.
- Safety harnesses for all elevated workers.
- Proper ladder, cage, and safety operation.
Check all components and parts before installation. All parts are marked with a part
number, please refer to the parts list to make sure you have all parts.
Choose a day with low or no wind to install, assembly is hard in heavy wind. Do not
make any alterations to the structure. Do not hang any weights on the frame during
installation, including parts. We are not responsible for any damages or injuries
caused by inappropriate installation, unauthorized modifications or extreme weather.
This building is not intended for human occupancy.
It is recommended to tape or add foam/rubber on the frame where joints connect and
where it touches the cover. This will help extend the life span of the cover.
Read the following item list carefully and count the number of items to ensure that all
parts are included prior to setup.
Installation steps
Step 1 : Review the whole structure and choose the proper installation site
Choose a solid flat level ground area to set up the building. Do not install the building
on soft ground, wetland, uneven surfaces, sloped surfaces, or on top of structures that
are not rated to hold its weight.
We strongly recommend that you build the structure on a solid foundation such as
cement and use anchor bolts on all baseplates.
Be aware of the surrounding area. Do not set up the building near snowdrifts, open
flames or exposed electrical wires. Do not keep heat sources near the fabric cover.

▶W W W . T M G I N D U S T R I A L . C O M P 2 / 19 T o l l F r e e : 1 - 877-761-2819
Keep the building surroundings clear at all times.
TMG-ST2041V Part List
Parts
code
Graphical
Description
length
Qty
1
Peak arch tube
φ48xL1820mm
9
2
Upper rafter tube
(middle truss)
φ48xL1934mm
14
2A
Upper rafter tube
(front truss)
φ48xL1934mm
4
3
Shoulder tube
(middle truss)
φ48xL1123mm
14
3A
Shoulder tube
(front and rear truss)
φ48xL1123mm
4
4
Sidewall tube
φ48x1480mm
18
5
Roof purlin
(horizontal tube)
φ42x1440mm
72
5A
Middle truss
connectors
W50xL170mm
126
5B
Front and rear
connectors
W50xL111mm
18
5C
Self-tapping screws
#12x25mm
81
5L
Left corner baseplate
(front and rear truss)
W200xL350mm
2

▶W W W . T M G I N D U S T R I A L . C O M P 3 / 19 T o l l F r e e : 1 - 877-761-2819
5R
Right corner baseplate
(front and rear truss)
W200xL350mm
2
6
Door column baseplate
(front truss)
W150xL200mm
4
7
Middle truss baseplate
W150xL200mm
14
7A
Ratchet
2T
18
8
Door frame lower tube
(front and rear truss)
φ48xL1980mm
4
9
Door frame upper tube
(front and rear truss)
φ48xL1405mm
4
10
Door frame horizontal
tube
(front and rear truss)
φ42xL1446mm
4
11
Ceiling cross bar
φ42xL1949mm
9
11A
Two wheel rope pulley
(pre-installed on 2A)
W30xL130mm
2
11B
One wheel rope pulley
(pre-installed on 2A)
W30xL85mm
2
12
Bottom tension bar
(front and rear cover)
φ32xL1300mm
4
13
Diagonal bracing bar
(1st and last span)
φ32xL1920mm
4
13A
Tube clamp
φ48mm
8
14
Top cover tension tube
(for both bottom sides)
φ32xL1993mm
2 groups
φ32xL500mm
15
Door dropping tube
φ32xL1993mm
2 groups
φ32xL1360mm

▶W W W . T M G I N D U S T R I A L . C O M P 4 / 19 T o l l F r e e : 1 - 877-761-2819
16
Expansion bolt
(not included)
φ14x100mm
62
17
Half round head bolt
M8x60mm
162
18
Hex Bolt
M10x70mm
168
19
Hex Bolt
M10x30mm
26
19A
Hex Bolt
M10x50mm
8
20
Nylon rope
φ8xL12m
4
21
Water plug
φ32mm
16
22
Top cover
1
23
Front cover panel
2
24
Braided rope
φ8xL180m
1 bundle
25
Ratchet straps
W38xL800mm
18
26
Scratch resistant tape
10m
3

▶W W W . T M G I N D U S T R I A L . C O M P 5 / 19 T o l l F r e e : 1 - 877-761-2819
Step 1 : Base plates installation.
Installation diagram of expansion bolt.
NO.
Part
Qty
NO.
Part
Qty
5L
2
7
14
5R
2
16
62
6
4

▶W W W . T M G I N D U S T R I A L . C O M P 6 / 19 T o l l F r e e : 1 - 877-761-2819
Step 2 : Install front and rear truss.
NO.
Part
Qty
NO.
Part
Qty
1
2
11A
2
2A
4
11B
2
3A
4
18
24
4
4
19
4
11
2

▶W W W . T M G I N D U S T R I A L . C O M P 7 / 19 T o l l F r e e : 1 - 877-761-2819
Step 3 : Install the middle truss.
NO.
Part
Qty
NO.
Part
Qty
1
7
11
7
2
14
18
84
3
14
19
14
4
14

▶W W W . T M G I N D U S T R I A L . C O M P 8 / 19 T o l l F r e e : 1 - 877-761-2819
Step 4 : Wrap (#26) around the sharp points of the joint to avoid friction
between the fabric and the interface.
NO.
Part
Qty
26
3

▶W W W . T M G I N D U S T R I A L . C O M P 9 / 19 T o l l F r e e : 1 - 877-761-2819
Step 5 : Put up the front and rear truss and the intermediate trusses.
NO.
Part
Qty
18
36

▶W W W . T M G IN D U ST R I A L . CO M P 10/ 1 9 T o l l F r ee : 1 - 877-761-2819
Step 6 : Install (#5) roof purlin.
NO.
Part
Qty
NO.
Part
Qty
5
72
5C
81
5A
126
17
162
5B
18

▶W W W . T M G IN D U S T R I A L. C O M P 11/ 1 9 T o l l F r ee : 1 - 877-761-2819
Step 7 : Install the diagonal bracing bars (#13).
NO.
Part
Qty
13
4
13A
8
19A
8

▶W W W . T M G IN D U S T R I A L. C O M P 12/ 1 9 T o l l F r ee : 1 - 877-761-2819
Step 8 : Install the remaining parts on the front and rear trusses.
NO.
Part
Qty
NO.
Part
Qty
8
4
18
16
9
4
19
8
10
4
21
8
12
4

▶W W W . T M G IN D U S T R I A L. C O M P 13/ 1 9 T o l l F r ee : 1 - 877-761-2819
Step 9 : Install front and rear cover panel.
Lift up (#23) cover panels, starting from the center point of the frame (highest
ridge point) ，use ropes (#24) Center point through thegrommets to tie the panel
to the truss firmly. Then continue from the middle to the sides to tie the panels to
the arch pipe.
Insert the dropping tube (#15) into the bottom groove pocket on the door cover.
Tie two ropes (#20) separately on both sides of the peak arch tube. Pull both
ropes under through the bottom of the door cover from the back, then go up from
front and through both pulley11A and 11B.
NO.
Part
Qty
Rope Shear Size
15
2
24
Qty
20
4
A
18000mm
2
21
4
B
4500mm
2
23
2
C
2000mm
8
24
70m

▶W W W . T M G IN D U S T R I A L. C O M P 14/ 1 9 T o l l F r e e : 1 - 877-761-2819
What you see in this photo is outside
The rope coming out from pulley11B must go through the upper wheel of pully
11A, then pull both ropes together slowly and start to lift the door cover.
Tie both ropes to the corner baseplate. Now the door cover is up. When you drop
down the door cover, do not let go too quick, otherwise it might get stuck and
damage the fabric.

▶W W W . T M G IN D U S T R I A L. C O M P 15/ 1 9 T o l l F r e e : 1 - 877-761-2819
Step 10 : Install the top cover (#22) stretch and tighten top cover.
Do not install the cover during windy weather!
Stretch and adjust the cover from back and forth, to make sure it is square and
centered.
Unpack the top cover and place it along one of the long sides of the structure.
Use 3 to 5 ropes (#22) to pull the cover over the top of the structure, from the
inside 2 or 3 people standing inside on ladders to push upwards will help to move
the cover without any damage.

▶W W W . T M G IN D U S T R I A L. C O M P 16/ 1 9 T o l l F r e e : 1 - 877-761-2819
NO.
Part
Qty
NO.
Part
Qty
NO.
22
1
24
1

▶W W W . T M G IN D U S T R I A L. C O M P 17/ 1 9 T o l l F r e e : 1 - 877-761-2819
Step 11 : Tension the cover on the structure from both sides.
NO.
Part
Qty
14
2
21
4

▶W W W . T M G IN D U S T R I A L. C O M P 18/ 1 9 T o l l F r e e : 1 - 877-761-2819
Step 12 : Install ratchet straps.
NO.
Part
Qty
7A
18
25
18

▶W W W . T M G IN D U S T R I A L. C O M P 19/ 1 9 T o l l F r e e : 1 - 877-761-2819
After the Installation
Walk around and inspect the shelter periodically to make sure all components are still
firmly secured and the whole shelter is well supported. Check all bolts and nuts as well
as all connection points to make sure they are all in good position. Check the base
plates, adjust the ropes and tie downs if required and clean the cover regularly.
Snow accumulating on the fabric cover must be removed as soon as possible. If snow
becomes solid ice on the cover, itwill increase the weight on the roof and may collapse
the shelter or reduce the life span.
Keep the shelter on a dry ground most of the time. Do not keep the fabric dirt skirt
under water all the time, otherwise the fabric will deteriorate.
We strongly recommend you remove any snow from the roof immediately. Do not
leave any snow load on the roof overnight. Keep 3 feet of clearance on all sides at all
times. Do not allow snow to accumulate and pile up on the sides of the building.
Otherwise the pressure from the sides will push inwards and could lead to a collapse.