TMG TMG-MSC2030F User manual

ڼWWW.TMGINDUSTRIAL.COM P0/14 Toll Free:1-877-761-2819

ڼWWW.TMGINDUSTRIAL.COM P1/14 Toll Free:1-877-761-2819
Main specifications :
xAssembly size : W6 x L9 x H3.8 (m) / 19.7 x 29.5 x 12.5 (ft)
xWidth : 6m / 19.7 ft
xLength : 9m / 29.5 ft
xRidge Peak Height : 3.8 m / 12.5 ft
xShoulder height : 2.9 m / 9.5ft
Prior to assembly
Please read the instructions carefully before installation. It is very important to follow
your local safety regulations and industry standards during installation. Regulations may
include but are not limited to:
• Safety helmets, protective eyewear, and clothing
• Safety harnesses for all elevated workers
• Proper ladder, cage, and safety operation
Check all components and parts before installation. All parts are marked with a part
number, please refer to the parts list to ensure you have all parts.
Choose a day with low or no wind to install, it is hard to assemble with heavy wind. Do
not make any alterations to the structure. Do not hang any weight on the frame during
installation, including parts. We are not responsible for any damages or injuries caused by
inappropriate installation, unauthorized modifications or extreme weather.
This building is not intended for human occupancy.
Check the parts list below to make sure all parts are received prior to assembly.

ڼWWW.TMGINDUSTRIAL.COM P2/14 Toll Free:1-877-761-2819
Frame structure diagram

ڼWWW.TMGINDUSTRIAL.COM P3/14 Toll Free:1-877-761-2819
TMG-MSC2030F Part List
Parts
Code
Graphical Description Length
Qty
1
Peak arch tube L1668mm
7
2
Middle rafter tube
L1880mm
14
3
Shoulder tube L1188mm
8
3A
Shoulder tube L1188mm
6
4
Sidewall tube
L1924mm
14
4A
Short casing L198mm
42
5
Baseplate
W150xL200mm
14
5A
Side edge crossbar
(front and rear truss)
L1570mm
4
5B
Side edge crossbar
(middle truss)
L1500mm
8
5C
Top cross bar A L1500mm
30
5D
Top cross bar B L1550mm
6
6
Ceiling cross bar
L1763mm
7
6A
Metal sheet
W870xL1680mm
44
6C
Short casing L100mm
30
6D
Reinforcing tube
L740mm
14
6E
Reinforced tube
mounting plate
L100mm
56
6F
Reinforced tube
mounting plate
L100mm
28
7
Metal sheet
W870xL1620mm
12
7A
Metal sheet
W
580
xL1620mm
4

ڼWWW.TMGINDUSTRIAL.COM P4/14 Toll Free:1-877-761-2819
8
Metal sheet
W870xL1600mm
24
8A
Metal sheet
W
580
xL1600mm
8
9
Edge protector L1430mm
8
10
Edge buckle L200mm
4
11
Edge protector(top)
L1600mm
6
12
Eyebolt M10x90mm
6
13
Anchor hook φ16
x120mm
6
14
Steel cable L3.9m
6
14A
Steel cable L5m
7
15
Expansion bolt φ
16 x 150mm
28
16
Drill φ3.5mm
2
17
Hex bolt
M10 x 70mm
266
18
Self tapping screw
#12 x 30mm
512
19
Blind rivet φ3x10mm
72
20
Sleeve φ8mm
2
21
Self locking bolt
and nuts
M10x10
0mm
42
21A
Self locking bolt
and nuts
M10x50mm
30
23
Square plug 35x35mm
12

ڼWWW.TMGINDUSTRIAL.COM P5/14 Toll Free:1-877-761-2819
Step 1 : Baseplate positioning and installation.
xThe diagonal X and Y must be equal.
xInstallation diagram of expansion bolt.
No.
Part
Qty
5
14
15
28

ڼWWW.TMGINDUSTRIAL.COM P6/14 Toll Free:1-877-761-2819
Step 2 : Install all trusses.
xInstall front, rear and middle trusses.
No.
Part
Qty
No.
Part
Qty
1
1x3
6
1x3
2
2x3
6D
2x3
3A
2x3
6E
8x3
4
2x3
6F
4x3
4A
6x3
17
34x3

ڼWWW.TMGINDUSTRIAL.COM P7/14 Toll Free:1-877-761-2819
xInstall other trusses. (4 trusses)
No.
Part
Qty
No.
Part
Qty
1
1x4
6
1x4
2
2x4
6D
2x4
3
2x4
6E
8x4
4
2x4
6F
4x4
4A
6x4
17
34x4

ڼWWW.TMGINDUSTRIAL.COM P8/14 Toll Free:1-877-761-2819
Step 3 : Put up the all trusses, install the wire rope.
No.
Part
Qty
14A
7
17
28

ڼWWW.TMGINDUSTRIAL.COM P9/14 Toll Free:1-877-761-2819
Step 4 : Install top cross bar.
No.
Part
Qty
No.
Part
Qty
5C
30
21
42
5D
6
21A
30
6C
30
23
12

ڼWWW.TMGINDUSTRIAL.COM P10/14 Toll Free:1-877-761-2819
Step 5 : Install side panels.
No.
Part
Qty
No.
Part
Qty
5A
4
8A
8
5B
8
9
8
7
12
10
4
7A
4
18
248
8
24

ڼWWW.TMGINDUSTRIAL.COM P11/14 Toll Free:1-877-761-2819
Step 6 : Install the roof panels.
No.
Part
Qty
6A
4
18
24

ڼWWW.TMGINDUSTRIAL.COM P12/14 Toll Free:1-877-761-2819
No.
Part
Qty
No.
Part
Qty
6A
40
18
240
11
6
19
72

ڼWWW.TMGINDUSTRIAL.COM P13/14 Toll Free:1-877-761-2819
Step 7 : Install the wire rope.
No.
Part
Qty
No.
Part
Qty
12
6
14
6
13
6

ڼWWW.TMGINDUSTRIAL.COM P14/14 Toll Free:1-877-761-2819
After the Installation
Walk around and inspect the carport periodically to make sure all components are still
firmly secured and the whole carport is well supported. Check all bolts and nuts as well as
all connection points to make sure they are all in good position. Check the base plates,
adjust the ropes and tie downs if required and clean the cover regularly.
Snow accumulating on the cover must be removed as soon as possible. If snow becomes
solid ice on the cover, it will increase the weight on the roof and may collapse the carport
or reduce the life span.
We strongly recommend you remove any snow from the roof immediately. Do not leave
any snow load on the roof overnight. Keep 3 feet of clearance on all sides at all times. Do
not allow snow to accumulate and pile up on the sides of the building. Otherwise the
pressure from the sides will push inwards and could lead to a collapse.

ATTENTION
TO ENSURE THAT YOUR CARPORT SHED HAS BEEN
SECURELY INSTALLED AND ITS WARRANTY VALIDITY, IT IS
IMPORTANT TO READ THE FOLLOWING PAGES CAREFULLY.
^ŚŽƵůĚĞƌ^ƵƉƉŽƌƚƌĂĐŝŶŐ
;ZĞŝŶĨŽƌĐŝŶŐdƵďĞͿ
^ƚĞĞůŶĐŚŽƌĂďůĞƐ
ŶĐŚŽƌŽůƚƐŽŶŽŶĐƌĞƚĞWĂĚƐ
;ĂƚůĞĂƐƚϲƚŚŝĐŬͿ

As the owner of your product, it is important to take the necessary steps to ensure its
stability and durability, especially in areas where heavy snow or high winds are common.
Following these three steps will help prevent any damage due to snow or wind loads, and
ensure that the product warranty remains valid.
1. Shoulder Support Bracing (Reinforcing Tube)
Shoulder support bracing is installed on both sides of the truss to provide additional
support to the structure. This helps to distribute the weight of snow and wind loads
evenly across the structure, preventing any one area from bearing too much weight.
The bracing should be installed according to the manufacturer's instructions,
ensuring that it is securely attached to the truss.
2. Steel Anchor Cables
Steel anchor cables are a critical component of the shed's stability, as they hold the
shed firmly to the ground and prevent it from being lifted or shifted by wind or snow
loads. These cables should be installed on all four corners of the shed and attached
to the ground using suitable anchors. It is important to ensure that the cables are
securely anchored to the ground, as any loosening could compromise the shed's
stability.
3. Concrete Pad and Anchor Bolts
Installing the shed on a concrete pad or equivalent provides a stable foundation for
the shed and helps to prevent it from shifting or settling over time. Anchor bolts
should be used to secure the shed firmly to the concrete pad, ensuring that it does
not move during high winds or heavy snow loads. It is important to ensure that the
anchor bolts are installed according to the manufacturer's instructions and that they
are tightened securely.
It is important to note that the shed is not engineered to handle snow and wind loads, and
the engineering drawing is not available from the seller. Therefore, it is crucial to check the
local building codes and regulations to determine if a permit is required for the installation
of the shed. In some areas, a permit may be required for any type of structure, regardless of
whether it is engineered to handle snow and wind loads.
If a permit is required and the shed does not meet the engineering requirements, it may not
be possible to obtain a permit for its installation. In such cases, it may be necessary to
either modify the shed to meet the engineering requirements or to choose a different type
of structure that is designed to handle snow and wind loads. Any modifications required to
meet building codes and regulations are the sole responsibility and expense of the owner.
In summary, it is important to prioritize safety and compliance with local building codes
and regulations to avoid any potential safety hazards or legal issues in the future. By
following these three steps, you can ensure the stability and durability of your shed and
prevent any damage due to snow or wind loads. Remember, failure to follow these steps
may result in the voiding of the product warranty.