TMG TMG-ST3041CE User manual

▶WWW.TMGINDUSTRIAL.COM P 1/ 15 T oll F re e: 1 -877-761- 2 819
Main Specifications :
Overall assembled size : W9.15 x L11.97 x H3.0 (m) / 30 x 39.27 x 9.84(ft)
Ridge Peak Height : 3 m / 9.84ft + container height
Prior to assembly
Please read the instructions carefully before installation. It is very important to
follow your local safety regulations and industry standards during installation.
Regulations may include but are not limited to:
- Safety helmets, protective eyewear, and clothing
- Safety harnesses for all elevated workers
- Proper ladder, cage, and safety operation
Check all components and parts before installation. All parts are marked with a part
number, please refer to the parts list to make sure you have all parts.
Choose a day with low or no wind to install, assembly is hard in heavy wind. Do not
make any alterations to the structure. Do not hang any weights on the frame during
installation, including parts. We are not responsible for any damages or injuries caused by
inappropriate installation, unauthorized modifications or extreme weather.
This building is not intended for human occupancy.
It is recommended to tape or add foam/rubber on the frame where joints connect and
where it touches the cover. This will help extend the life span of the cover.
Read the following item list carefully and count the number of items to ensure that all
parts are included prior to setup.
Installation steps
Step 1 : Review the whole structure and choose the proper installation site
Choose a solid flat level ground area to set up the building. Do not install the building on
soft ground, wetland, uneven surfaces, sloped surfaces, or on top of structures that are not
rated to hold its weight.
We strongly recommend that you put the containers on hard foundations before installing
the shelter.
Be aware of the surrounding area. Do not set up the building near snowdrifts, open flames
or exposed electrical wires. Do not keep heat sources near the fabric cover. Keep the
building surroundings clear at all times.

▶WWW.TMG IN DUST RI AL .C OM P 2 /1 5 T o ll F r ee :1 - 877-761-2 8 19
Structure diagram

▶WWW.TMG IN DUST RI AL .C OM P 3 /1 5 T o ll F r ee :1 - 877-761-2 8 19
TMG-ST3041CE Part List
No.
Picture
Description
Length
Quantity
1
Peak arch tube
L1734mm
10
2
Middle rafter tube
L2890mm
20
3
Shoulder tube
L1784mm
12
3A
Shoulder tube
L1784mm
8
4
Middle truss baseplate
W150xL200mm
16
4L
Left corner baseplate
(front and rear truss)
W150xL200mm
2
4R
Right corner baseplate
(front and rear truss)
W150xL200mm
2
5
Roof purlin
(horizontal tube)
L1268mm
63
5A
Middle truss connectors
W50xL180mm
112
5B
Front and rear connectors
W50xL121mm
14
5C
Self-tapping screws
(#12x25mm)
#12x25mm
70
6
Ceiling cross bar
L2190mm
10
7
Sidewall frame steel
tension cables
L1300mm
8
7A
Ratchet
2T
20
7B
Ratchet straps
W38xL800mm
20
8
Mounting base
W40xL100mm
8
9
Top cover tension tube
(for both bottom sides)
L1993mm
12

▶WWW.TMG IN DUST RI AL .C OM P 4 /1 5 T o ll F r ee :1 - 877-761-2 8 19
9A
Top cover tension tube
L490mm
2
10
Bolt M8x60
M8x60mm
126
11
Bolt M8x70
M8x70mm
120
12
Hex bolt
M10x30mm
M10x30mm
20
13
Top cover
1
14
Braided rope (80m)
φ8x80m
1
15
Scratch resistant tape
10m
2
16
Water plug
φ32
4

▶WWW.TMG IN DUST RI AL .C OM P 5 /1 5 T o ll F r ee :1 - 877-761-2 8 19
Step 2 : Place the containers making sure they are parallel and the correct width
apart. Make sure there is a gap of about 3 feet around the building. the center point
of the round pipe of the base is the reference point, and the diagonal X and Y must
be equal. The base plate shall be welded to the top of the container on the same
horizontal plane to ensure that the welding is firm and reliable.
No.
Part
Qty
4
16
4L
2
4R
2

▶WWW.TMG IN DUST RI AL .C OM P 6 /1 5 T o ll F r ee :1 - 877-761-2 8 19
Step 3 : Connect all trusses.
Front and rear trusses (4 trusses).
No.
Part
Qty
No.
Part
Qty
1
1x4
6
1x4
2
2x4
11
8x4
3A
2X4
12
2x4

▶WWW.TMG IN DUST RI AL .C OM P 7 /1 5 T o ll F r ee :1 - 877-761-2 8 19
Middle trusses (6 trusses).
No.
Part
Qty
No.
Part
Qty
1
1x6
6
1x6
2
2x6
11
8x6
3
2X6
12
2x6

▶WWW.TMG IN DUST RI AL .C OM P 8 /1 5 T o ll F r ee :1 - 877-761-2 8 19
Lay down all (10) trusses on the ground when the assembly is all completed and before
moving to next step, and then wrap (#15) around the sharp points of the joint to avoid
friction between the fabric and the interface, resulting in fabric damage.
No.
Part
Qty
15
2

▶WWW.TMG IN DUST RI AL .C OM P 9 /1 5 T o ll F r ee :1 - 877-761-2 8 19
Step 4 : Put up all trusses.
Install each truss on the base tube. Use hex bolt (#11) to secure the truss to the base
tube firmly. We recommend to use a crane or forklift to lift the truss and have 2 to
3 people on site to work together. Please make sure it is safe and secure when
installation is proceeding.
No.
Part
Qty
11
40

▶WW W.TM GIND USTRIA L.C OM P 10/15 T o ll Fre e:1 - 877-761-2819
Step 5 : Install cross tubes and wire ropes.
No.
Part
Qty
No.
Part
Qty
5
63
7
8
5A
112
8
8
5B
14
10
126
5C
70

▶WW W.TM GIND USTRIA L.C OM P 11/15 T o ll Fre e:1 - 877-761-2819
Overall structural inspection :
Check all components and trusses to ensure the entire structure is rectangular as specified
in (picture1). All trusses must be 90 degrees straight up from the container.
Secure and tighten all bolts and nuts on this step. But do not over tie! Otherwise you
might damage the tubes or components.
Step 6 : Install the top cover (#13) stretch and tighten top cover.
Do not install the cover during windy weather!
Stretch and adjust the cover from back and forth, to make sure it is square and
centered.
Unpack the top cover and place it along one of the long sides of the structure.
Use 3 to 5 ropes (#13) to pull the cover over the top of the structure, from the
inside 2 or 3 people standing inside on ladders to push upwards will help to
move the cover without any damage.

▶WW W.TM GIND USTRIA L.C OM P 12/15 T o ll Fre e:1 - 877-761-2819
NO.
Part
Qty
Rope Shear Size
13
1
14
Qty
14
80m
14
2000mm
4

▶WW W.TM GIND USTRIA L.C OM P 13/15 T o ll Fre e:1 - 877-761-2819
Step 7 : Tension the cover on the structure from both sides.
 Insert tension tubes (#9) slowly into the bottom groove pocket on both long
sides. Add the water plug (#16) on the first tension tube to avoid tearing the
fabric and add one to the end of last tube as well.
 Repeat the same step for the other side.
NO.
Part
Qty
9
12
9A
2
16
4

▶WW W.TM GIND USTRIA L.C OM P 14/15 T o ll Fre e:1 - 877-761-2819
Step 8 : Install ratchet straps.
 Stretch and adjust the cover from left and right, back and forth, to make sure
it is square and centered. Cut the groove pocket where it aligns with ratchet
(#7A), and use strap (#7B) to pull tension tube (#9) to ward the ratchet and
secure it.
 Evenly adjust all ratchets on both sides to take wrinkles out and make the
cover flat and smooth.
NO.
Part
Qty
7A
20
7B
20

▶WW W.TM GIND USTRIA L.C OM P 15/15 T o ll Fre e:1 - 877-761-2819
After Installation
Walk around and inspect the building periodically to make sure the parts are firmly
fixed and the whole building is well supported. Check all bolts and hardware
connectors to make sure they are in place and tightened. Check the base plates,
adjust the ropes if necessary and clean the cover regularly.
Snow accumulating on the fabric cover must be removed as soon as possible. If
snow is allowed to become solid ice on the cover, it could increase the weight on the
roof and collapse the building or reduce the life span.
We strongly recommend you remove any snow from the roof immediately. Do not leave
any snow load on the roof overnight. Keep 3 feet of clearance on all sides at all times. Do
not allow snow to accumulate and pile up on the sides of the building. Otherwise the
pressure from the sides will push inwards and could lead to a collapse.