Toro Sand Pro 140-0274 User manual

FormNo.3440-384RevA
DragMatKit
SandPro®TractionUnit
ModelNo.140-0274
InstallationInstructions
Installation
LooseParts
Usethechartbelowtoverifythatallpartshavebeenshipped.
DescriptionQty.Use
Weightkit100-6442Not
included
Frontliftframekit08712Not
included
Installtheweightstothemachine(Models08703,08705,
08743,or08745)orthefrontliftframe(Models08705or
08745only).
Dragmat1
Chain1
Screw(5/16x1-1/2inches)1
Locknut(5/16inch)1
Installthechaintothedragmat.
Leftcradle1
Rightcradle1
Bolt(3/8x1-3/8inches)4
Flangenut(3/8inch)4
Washer(3/8inch)4
Shackle1
Clevispin1
Hairpincotter1
Installthecradles.
Important:FortractionunitModels08703or08743,youmustinstallweightkit100-6442before
operatingthisattachment.
Important:FortractionunitModels08705or08745,youmustinstalleitherweightkit100-6442orfront
liftframekit08712beforeyouoperatethisattachment.
Important:Youmustinstallanishgraderontherearofthemachinebeforethedragmatcan
beinstalled.
©2020—TheToro®Company
8111LyndaleAvenueSouth
Bloomington,MN55420
Registeratwww.T oro.com.OriginalInstructions(EN)
PrintedintheUSA
AllRightsReserved*3440-384*A

InstallingtheWeightsor
FrontLiftFrame
Note:Ensurethatyourmachinehastheappropriate
numberofweights.Ifnecessary,installadditional
weightsfromweightkit100-6442(soldseparately).
1.Parkthemachineonalevelsurface,engage
theparkingbrake,removethekey(ifequipped),
andwaitforallmovingpartstostop.
2.Ifyouareinstallingfrontliftframekit08712refer
totheinstructionsprovidedwiththatkit.
3.Ifyouareinstallingweightkit100-6442referto
theinstructionsprovidedwiththatkit;markand
drill2holesoneachsideofthefrontcasterfork
asshowninFigure1.
Note:Somemachinesmayhaveexistingholes.
g024837
Figure1
1.37.4mm(1-1/2inches)4.112.5mm(4-7/16inches)
2.Drillapairof13.5mm
(17/32inch)holesat
thislocationusingthe
dimensionsprovided
5.31.7mm(1-1/4inches)
3.127mm(5inches)
InstallingtheChaintothe
DragMat
Secure1endofthechaintothedragmatwithascrew
(5/16x1-1/2inches)andalocknut(5/16inch);refer
toFigure2.
g024788
Figure2
1.Locknut(5/16inch)3.Screw(5/16x1-1/2
inches)
2.Chain
2

InstallingtheCradles
1.Installthecradlestothenishgrader;referto
Figure3.
g024786
Figure3
1.Finishgrader6.Chain
2.Flangenut,(3/8inch)7.Shackle
3.Cradle8.Hairpincotter
4.Bolt(3/8x1-3/8inches)9.Clevispin
5.Washer(13/32inch)
2.Connectthelooseendofthechaintothedraw
barorthenishgraderwiththeshackle,the
clevispin,andthehairpincotter;refertoFigure
3.
Operation
StowingtheDragMat
Wheneveryouarenotusingthedragmat,stowitin
thecradles.
Tostowthedragmat,simplyrollitupandplaceitin
thecradles.
UsingtheDragMat
Important:Donotdrivethemachinebackward
whenthedragmatisconnectedandonthe
ground;thedragmatgetscaughtunderthe
wheels,anddamagesthemachine.
Usecautionwhileoperatingthemachinewiththedrag
matinstalled.Keepoperatingspeedstoaminimum
acceptablelevel.Formaximummatlife,avoidareas
andobjectsthatmaysnagorinterruptthetravelof
themat.
1.Withthedragmatstowedinthecradles,drive
themachinetoanareathatrequiresgrooming.
2.Removethedragmatfromthecradles,and
placeitontheground.
3.Pullthedragmatoverthesurfacethatrequires
grooming.
4.Whenyouhavenishedorarereadytogrooma
differentarea,stowthedragmatinthecradles.
CleaningtheDragMat
Keepthedragmatclean.Excessivesoilbuildup
increasestheattachmentweightandmayaffect
handlingofthemachine.
3