unGer Rinse n Go User manual

1
User Manual
Read carefully for safety, assembly
and operating instructions prior to
using this product.

2
TABLE OF CONTENTS
DANGER
READ USER MANUAL BEFORE USING PRODUCT.
Introduction.......................................................................................................................... 3
1.0 Safety Information ................................................................................................. 4-5
2.0 System Products & Accessories......................................................................... 6-7
3.0 Assembly Instructions............................................................................................... 8
4.0 Use and Operation...............................................................................................9-10
5.0 Pure Water Production............................................................................................11
6.0 System Maintenance - Replacing Resin Filter & Care .......................... 12-13
7.0 Storage.........................................................................................................................13
8.0 Environmental Information ..................................................................................13
9.0 TDS Meter....................................................................................................................14
Product Guarantee...........................................................................................................15
CONTENTS UNDER PRESSURE. DO NOT USE IF THE SYSTEM IS
CRACKED OR DAMAGED. CAN CAUSE SEVERE INJURY OR DEATH
FROM TANK RUPTURE OR IMPROPER USE.
THIS PRODUCT CONTAINS A BUTTON BATTERY. IF SWALLOWED,
IT COULD CAUSE SEVERE INJURY OR DEATH IN JUST 2 HOURS.
SEEK MEDICAL ATTENTION IMMEDIATELY

3
INTRODUCTION
Thank you for your purchase of the Unger Professional Rinse ‘n’ Go™ System.
This manual will help you get set up and begin using your product right away.
When used as intended, this system will produce low total dissolved solids or
TDS (less than 20 ppm) pure water for auto and glass cleaning.
The science behind this product is called deionization, or ion exchange. In this
process, the minerals responsible for leaving spots on your car and windows are
removed from the water. So, you can rinse the surface, walk away, and still get
spot-free and streak-free results. This water is meant to be used for the nal rinse
of your car. You still need to wash dirt and grime off of your car as you would
normally do when washing your car. However, instead of spending all of that
time drying it by hand, you can rinse the car with this water and just walk away.
The Unger Professional Rinse ‘N’ Go System contains mixed bed ion exchange
resin to remove impurities out of ordinary tap water, turning it into what is
commonly referred to as pure water. Such impurities are referred to as total
dissolved solids (TDS) and are measured in parts per million (ppm). Water
is considered 100% demineralized or pure when its TDS is measured at 0
ppm. The average TDS of drinking water is 180 ppm (see table in section
5.0). Pure water left on the surface will dry to a clean and spot-free appearance.
No power is required other than the tap water line pressure, which
typically ranges from 40-60 psi. This enables the system to produce pure water
at approximately 2.5 gallons per minute. Unger recommends testing the water
supply (TDS) before using this product at a pressure that does not exceed 90 psi
(see section 4.0 for more information).
Mixed bed ion exchange resin eventually becomes exhausted and no longer
able to remove impurities. A TDS meter is included with the system to
measure the TDS level in the water that comes out of the system. TDS is a
measure of how pure the water is. Water that contains a TDS of less than 20 ppm
should not leave spotting on the car. The TDS must be less than 10 ppm for
spot-free glass.
When TDS levels reach over 20 ppm the resin lter should be replaced.
Changing the resin lter is quick and easy (See section 6.0).

4
1.0 SAFETY INFORMATION
Prior to product assembly and start-up, it is essential that you observe the safety
information and instructions for installation and maintenance contained in this
manual. Unger is not liable for damage to application areas, plumbing system
components or persons. Unger is not liable for misuse or mishandling of the
product, including dropping, dragging or dismantling.
1.1 GENERAL WARNINGS:
• Never direct water towards eyes or face.
• KEEP OUT OF REACH OF CHILDREN AND PETS. Do not allow product to be
used as a toy. Close supervision is necessary when any appliance is used by or
near children.
• To prevent electrical shock, do not use near any sources of electricity, including
electric and power lines.
• Do not use on electrical equipment or appliances.
• After unpacking the product, be sure to carefully dispose of any plastic bags to
avoid injury.
• Use only as described in this manual. Use only manufacturer’s
recommended attachments.
• Be sure cover is in locked position prior to use.
• Do not exert excessive pressure on release mechanism as breakage may occur.
• Drain the water from the unit after each use.
• Do not allow unit or resin to freeze.
• Ensure work area has sufcient water drainage.
• Turn off water supply when not in use.
• Do not drink water produced by this product.
1.2 WHEN STARTING SYSTEM:
• For use only with tap water.
• Do not connect to pressure washer or auxiliary pump.
• Do not exceed water pressure of 90 psi.
• Check system for cracks/damage.
• Be sure cover is in fully locked position.

5
1.3 BEFORE OPENING SYSTEM TO REPLACE RESIN:
• Shut off tap water supply.
• Open water output or press blue pressure release button down to
release pressure from system.
• Spilled resin is a slipping hazard. Clean up spilled resin immediately.
• Wash hands thoroughly after use.
• Resin can cause eye irritation. Avoid eye contact. In case of eye contact,
immediately ush eyes thoroughly with clean water. Consult doctor
if symptoms persist.
1.4 INTENDED USE:
This product is designed for personal use only. Always ensure that the product
is properly assembled, regularly maintained and used only as intended.
This product is meant to be used outside and stored at a temperature between
40°F - 100°F. Use this device only for water treatment to reach an optimal water
quality for spot-free cleaning. Any other use, especially water treatment for
food production (e.g., beverages) or drinking water consumption is prohibited.
Prior to product assembly and start-up, it is essential that you observe the safety
information and instructions for installation and maintenance contained in this
manual. Unger is not liable for damage to application areas, plumbing system
components or persons. Unger is not liable for misuse or mishandling of the
product, including dropping, dragging or dismantling.
1.1 GENERAL WARNINGS:
• Never direct water towards eyes or face.
• KEEP OUT OF REACH OF CHILDREN AND PETS. Do not allow product to be
used as a toy. Close supervision is necessary when any appliance is used by or
near children.
• To prevent electrical shock, do not use near any sources of electricity, including
electric and power lines.
• Do not use on electrical equipment or appliances.
• After unpacking the product, be sure to carefully dispose of any plastic bags to
avoid injury.
• Use only as described in this manual. Use only manufacturer’s
recommended attachments.
• Be sure cover is in locked position prior to use.
• Do not exert excessive pressure on release mechanism as breakage may occur.
• Drain the water from the unit after each use.
• Do not allow unit or resin to freeze.
• Ensure work area has sufcient water drainage.
• Turn off water supply when not in use.
• Do not drink water produced by this product.
1.2 WHEN STARTING SYSTEM:
• For use only with tap water.
• Do not connect to pressure washer or auxiliary pump.
• Do not exceed water pressure of 90 psi.
• Check system for cracks/damage.
• Be sure cover is in fully locked position.

6
2.0 SYSTEM PRODUCTS & ACCESSORIES
NOTE: When unpacking the product, make sure that no accessories are missing
and that none of the package contents have been damaged. (Refer to product box
for system content.)
RINSE 'N' GO DEIONIZATION SYSTEM OVERVIEW
This product can be connected to traditional garden hoses and used with
conventional car and window cleaning tools of your choice.
Outlet connection
Inlet connection
Pressure
release lever
Resin lter tank
Handle
Outlet
connection
plug
TDS Meter
(Filtered water out)
(Water in)
Inlet connection plug
Spotless Car Wash
Resin Filter
Replacement

7
SOAP BLASTING CAR WASH NOZZLE OVERVIEW (INCLUDED WITH SELECT MODELS)
Spray delivery
Container
Flow control
knob
Spray pattern
selector
Locking
trigger
TDS METER OVERVIEW
Battery
compartment
Hold
Maximum
immersion
level
TDS meter
electrode
LCD
Temperature On/Off
Protective
cap

8
• Unpack Unit: Inspect the Unger Professional
Rinse ‘n’ Go system and all components to
ensure there are no cracks or other damage.
Read all warnings and manual.
• Ensure there is a Resin Filter inside the unit.
(For instructions on how to open the unit,
see section 6.0).
• Water input connection must always be at
the bottom/base of the unit.
• If leaking or dripping occurs around
the hose connections, re-tighten the
connections by hand.
3.0 ASSEMBLY INSTRUCTIONS
Water input
Water output

9
Unger recommends testing the water supply for TDS prior to use in order to
determine approximately how many times you can rinse your car before
replacing the resin lter.
INSPECT THE RINSE ‘N’ GO SYSTEM PRIOR TO USE
Inspect system for leaks, cracks, or dents and proper t of top cap assembly.
Ensure hoses are properly attached and there are no leaks.
PREPARE THE SYSTEM FOR USE:
1. Locate water supply.
2. Set up system in upright position.
3. Choose a stable location where product is securely on the ground to
minimize toppling.
4. Connect water supply (garden hose) to inlet connection at the bottom of the unit
5. Connect garden hose to outlet connection.
4.0 USE AND OPERATION
Product needs to be upright for water
to ow through resin. If the product is on
its side, water won’t ow through resin
correctly, resulting in spots and/or streaks.
You may experience water dripping from around the pressure
release lever when you rst turn on and turn off the water
running into the unit. The Rinse ‘n’ Go is designed with an
air release valve to remove air from the unit. When the water
source is turned on, water will drip from around the pressure
release lever while the air is removed and until the internal
pressure reaches approximately 25 psi and the air release
valve seals. The same dripping may occur when the water
source is turned off and the internal pressure drops below
approximately 25 psi.

10
IF YOUR SYSTEM CAME WITH A SOAP BLASTING CAR WASH NOZZLE:
1. Fill container with your favorite concentrated car wash shampoo (do not add water).
2. Attach the spray nozzle to your garden hose.
WASHING YOUR CAR USING THE RINSE 'N' GO SYSTEM
• Wash your car as you normally would to remove dirt and grime. If your
system came with a Soap Blasting Car Wash Nozzle, you can use this to soap
up your car. We don’t recommend using the pure (deionized) water from
Rinse ‘n’ Go for this step.
• Using the Rinse ‘n’ Go system, rinse your car with pure (deionized) water.
If using the Soap Blasting Car Wash Nozzle, turn the ow control knob to the
water setting to ensure you don’t continue adding soap to the car.
• Make sure to rinse every part of the car with the water, including areas where
soap might get stuck, for example, around trunk, lights, and fuel door.
• For best results, rinse the car twice to remove all soap and ensure spot-free
results.
• You’re done! No need to hand dry your car. The puried water does all the
work for you so that your car will dry completely spot-free! Just like if you had
it cleaned at a professional car wash.
4.0 USE AND OPERATION (CONT.)
USING THE TDS METER
1. Remove the protective cap.
2. Press the ON/OFF button to turn the meter on.
3. When water begins to ow out of the unit, ll the protective
cap with the water.
4. Insert the meter into the capful of water for 5 seconds.
5. The LCD will indicate the ppm level of the water.
6. Press the HOLD button in order to view the LCD when meter is
removed from the water.
7. Press the ON/OFF button to turn the meter off.
8. Dry the meter completely before replacing the protective cap.
9. Return the TDS meter to the holder on the unit for storage.
When the TDS meter shows a reading of 20 ppm or higher,
spotting may occur and it is recommended that the resin lter
be replaced.

11
5.0 PURE WATER PRODUCTION
Tap water ows into the system’s lower connection port via tap pressure and
ows upwards through the Rinse ‘n’ Go tank. Pure water exits through the top
connection. When plumbing line pressures fall below 40 psi, a reduction in ow
rates will be noticeable.
The type of tap water you run through the system will impact how long you
are able to use the purifying resin lter before seeing spots and streaks. This
is often referred to as hard water. All water starts as soft water but the level of
minerals, such as magnesium and calcium, that are in the ground impact how
hard the water will become.
Soft water has a TDS reading of 100 ppm or less, while some regions with very
hard water have a TDS reading of 400 ppm or greater. This product is meant to
last 10 rinses with an average TDS reading of 200 ppm. To test the ppm level
of your water, you can use the TDS Meter to measure the water coming directly
out of the tap.
When washing your car, we recommend using the pure (deionized) water from
the Rinse ‘n’ Go System for the rinse portion of the process only. You can use
the pure water to apply the soap and wash your car, but you will run through
resin faster and it will not improve results.
Water TDS Reading Avg. # of rinses per
Resin Filter*
Soft <100 ppm 10 -12
Medium 100 – 250 ppm 10 -12
Hard 250 – 400 ppm 6-8
Very Hard 400 – 450 ppm 4-6
*All values based on 20 ppm as a maximum for pure water quality and an average
car rinse time of 4 minutes.

12
Unger does not recommend the use of any other resin except that which is
made specically for the Unger Professional Rinse ‘n’ Go. The use of any other
resin may cause damage to the system.
AFTER EACH USE
1. Shut off tap water supply.
2. Disconnect hoses from both ends of the unit.
3. Drain water from the unit by tilting the top of the unit forward and allowing
water to drain from the bottom of the tank, via the input connection.
4. Replace plug on both the inlet and outlet connection to prevent the resin
from drying.
OPENING THE UNIT AND REPLACING THE RESIN FILTER
1. Shut off tap water supply.
2. Press blue lever on system head and using a counterclockwise quarter turn,
release the system head from the rest of the system. Remove head and set aside.
3. Reach into tank and remove the bag by lifting it out of the unit, discard according
to local regulations.
4. Drop new resin lter into the tank, zip-tie facing up. You may need to pat down by
hand to ensure the entire bag ts well inside the chamber.
Do not remove resin from the nylon bag.
5. Re-attach system head by pushing down rmly and turning a quarter-turn
clockwise.
6.0 SYSTEM MAINTENANCE AND CARE
2 3 41 5

13
• The outer packing material can be recycled. Please recycle.
• Please dispose of used resin lter in accordance with applicable
federal, state/provincial and local laws and regulations.
8.0 ENVIRONMENTAL INFORMATION
7.0 STORAGE
1. Shut off tap water supply and disconnect hoses from both ends of the unit.
2. Drain water from the unit by tilting the top of the unit forward and allowing
water to drain from the bottom of the tank, via the input connection.
3. Replace plug on both the inlet and outlet connection to prevent the resin
from drying.
The system should be stored in a dry place at a temperature between
40°F - 100°F. Do not allow product to freeze or damage might occur.
Storing the product in an upright position is recommended. If storing the
product for longer than 6 months without using, remove the resin and discard
it in accordance with applicable federal, state/provincial and local laws and
regulations.
• Do not store resin in open or unlabeled containers.
• Store resin in a cool (40°F - 100°F), dry place.
CARE MUST BE TAKEN WHEN OPERATING AND SERVICING THIS PRODUCT.
THERE IS A RISK OF DAMAGE TO THE SYSTEM DUE TO:
• Operating and installation errors.
• Use of resin lter other than that specically made for Unger Professional Rinse ‘n’ Go.
• Use of loose resin (loose resin will most likely cause clogging and reduce ow rate).
• Pressure is not released correctly.
• Performing unauthorized modication to product.
• Improper maintenance and storage: Never store below freezing. Always seal unit
(inlet and outlet) between uses using plugs to prevent resin from drying out.

14
The TDS meter model HS-1510 included with the system is to measure the Total
Dissolved Solids (TDS) level in the water that comes out of the Rinse 'n' Go
system. TDS is a measure of how pure the water is. Water that contains a TDS of
less than 20 ppm should not leave spotting on the car. The TDS must be less
than 10 ppm for spot-free glass.
The TDS meter contains two button batteries. If swallowed, could cause severe
injury or death in just 2 hours. Seek medical attention immediately.
KEEP BATTERIES OUT OF REACH OF CHILDREN
Swallowing may lead to serious injury in as little as 2 hours or death, due to
chemical burns and potential perforation of the esophagus. If you suspect your
child has swallowed or inserted a button battery, immediately seek
urgent medical assistance.
HOW TO REPLACE THE BATTERIES:
• Pull open the battery compartment.
• Insert new batteries as indicated inside the battery compartment with the
positive and negative sides aligned.
• Replace both batteries at the same time (1.5V ‘LR44 type’ button batteries).
Do not mix old and new batteries or different battery types.
• Use only two 1.5V ‘LR44 type’ button batteries.
• Close battery compartment securely.
• Dispose of used batteries properly and immediately.
9.0 TDS METER
WARNING
BATTERIES

15
We design and test Unger products to ensure they meet our high quality
standards. We support this with the Unger Professional Product Lifetime
Guarantee. We will replace your Unger Professional Rinse ‘n’ Go System
if it does not meet our high quality standards for material, construction, or
workmanship.
THE GUARANTEE DOES NOT COVER:
• Damage caused by using the product in a commercial enterprise.
• Failing to follow Unger’s use and maintenance instructions.
• Operating and installation errors.
• Opening/disassembly of housing other than by Unger (except resin
replacement as described in section 6.0).
• Replacing connections and components or performing unauthorized
modications other than by Unger.
• Use of the system at more than 90 psi.
• Use of this product with a pressure washer or auxiliary pump.
• Replacement of purifying resin lters.
UNGER IS NOT LIABLE FOR THE FUNCTION OF THE PRODUCT WHEN:
• Use is not in accordance with product instructions.
• Failing to comply with safety instructions.
If you believe that your Unger Professional Rinse ‘n’ Go System does not meet
the guidelines as described for the Unger Professional Lifetime Guarantee,
please contact us at 1-800-833-6100. Unger may, at its discretion, require
return of the product for examination and testing. If a replacement product
is no longer available, Unger will replace your product with one of equal or
greater retail value at its sole discretion.
PRODUCT
LIFETIME GUARANTEE

16

17
Manuel d’utilisation
Lisez attentivement les instructions de
sécurité, assemblage et fonctionnement
avant d’utiliser le produit.

18
TABLE DES MATIÈRES
DANGER
LISEZ LE MANUEL AVANT D’UTILISER LE PRODUIT.
Introduction........................................................................................................................19
1.0 Informations De Sécurité................................................................................20-21
2.0 Produits Et Accessoires Du Système...........................................................22-23
3.0 Instructions D’Assemblage...................................................................................24
4.0 Utilisation Et Fonctionnement ......................................................................25-26
5.0 Production D’Eau Pure............................................................................................27
6.0 Maintenance du système -
Remplacement et entretien du ltre à résine ................................................28
7.0 Stockage......................................................................................................................29
8.0 Informations Environnementales.......................................................................29
9.0 dispositif de mesure TDS.......................................................................................30
Garantie du produit.........................................................................................................31
CONTENU SOUS PRESSION. NE PAS UTILISER SI LE SYSTÈME
EST FISSURÉ OU ENDOMMAGÉ POURRAIT PROVOQUER DES
BLESSURES GRAVES OU LE DÉCÈS À CAUSE DE LA RUPTURE DU
RÉSERVOIR OU DE L’UTILISATION INADÉQUATE.
CE PRODUIT CONTIENT UNE PILE BOUTON. EN CAS D'INGESTION,
ELLE POURRAIT CAUSER DES BLESSURES GRAVES OU LE DÉCÈS
EN 2 HEURES. CONTACTEZ UN MÉDECIN IMMÉDIATEMENT

19
INTRODUCTION
Merci pour votre achat du système Unger Professional Rinse ‘n’ Go™. Ce manuel
vous aidera à monter et à utiliser votre produit immédiatement. Lorsqu'il est utilisé
comme prévu, ce système produira de l'eau pure à faible teneur en solides dissous
ou TDS (moins de 20 ppm) pour le nettoyage de la voiture et le nettoyage des
vitres.
Le nom scientique derrière ce produit est désionisation, ou échange d'ions. Dans
ce processus, les minéraux responsables de la formation de taches sur la voiture
et les fenêtres sont enlevés de l'eau. Vous pouvez donc rincer la surface, vous
éloigner et obtenir des résultats sans taches ni traces. Cette eau est destinée à
être utilisée pour le rinçage nal de votre voiture. Vous devez toujours enlever la
saleté et la crasse de votre voiture comme vous le feriez normalement lorsque vous
la lavez. Cependant, au lieu de passer tout ce temps à le sécher à la main, vous
pouvez rincer la voiture avec cette eau et vous en aller.
Le système Rinse ‘N’ Go Unger Professional contient une résine qui réalise
l’échange d’ions à lit mélangé pour éliminer les impuretés de l’eau du robinet, ce
qui en fait une eau communément appelée eau pure. Ces impuretés sont appelées
matières solides totales dissoutes (TDS) et sont mesurées en parties par million
(ppm). L'eau est considérée à 100% comme étant déminéralisée ou pure lorsque
sa TDS est mesurée à 0 ppm. La moyenne TDS de l'eau de boisson est de 180 ppm
(voir le tableau de la section 5.0). L'eau pure laissée sur la surface s'assèche pour
donner un aspect propre et sans taches.
Aucune source d’énergie autre que la pression de la ligne d’eau du robinet n’est
nécessaire, valeur qui varie généralement de 40 à 60 psi. Cela permet au système
de produire de l’eau pure à un débit d’environ 2,5 gallons par minute. Unger
recommande de tester l'alimentation en eau (TDS) avant d'utiliser ce produit à une
pression ne dépassant pas 90 psi (voir la section 4.0 pour plus d'informations).
Aucune source d’énergie autre que la pression de la ligne d’eau du robinet n’est
nécessaire, valeur qui varie généralement de 40 à 60 psi. Cela permet au système
de produire de l’eau pure à un débit d’environ 2,5 gallons par minute. Unger
recommande de tester l'alimentation en eau (TDS) avant d'utiliser ce produit à une
pression ne dépassant pas 90 psi (voir la section 4.0 pour plus d'informations).
Lorsque les niveaux de TDS dépassent 20 ppm, le ltre à résine doit être remplacé.
Le changement du ltre en résine est simple et rapide (voir section 6.0).

20
1.0 INFORMATIONS DE SÉCURITÉ
Avant l'assemblage et la mise en service du produit, il est essentiel de respecter
les informations de sécurité et les instructions d'installation et de maintenance
contenues dans ce manuel. Unger n'est pas responsable des dommages causés aux
zones d'application, aux composants du système de plomberie ou aux personnes
Unger n'est pas responsable des utilisations ou manipulations incorrectes du produit,
notamment des chutes, des traînées ou des démontages.
1.1 AVERTISSEMENTS GÉNÉRAUX:
• Ne dirigez jamais l'eau vers les yeux ou le visage.
• TENEZ HORS DE LA PORTÉE DES ENFANTS ET DES ANIMAUX DE COMPAGNIE
Ne laissez pas le produit être utilisé comme un jouet. Une surveillance étroite est
nécessaire lorsqu'un appareil est utilisé par ou à proximité d'enfants.
• An d'éviter tout risque d'électrocution, ne l'utilisez près d'aucune source
d'électricité, y compris de lignes électriques.
• Ne pas utiliser sur des appareils électriques.
• Après avoir déballé le produit, assurez-vous de jeter soigneusement les sacs en
plastique pour éviter les blessures.
• Utilisez uniquement comme décrit dans ce manuel. Utilisez uniquement le
fabricant pièces jointes recommandées.
• Assurez-vous que le couvercle soit en position verrouillée avant l’utilisation.
• N'exercez pas de pression excessive sur le mécanisme de déclenchement, car
cela pourrait provoquer une rupture.
• Videz l'eau de l'appareil après chaque utilisation.
• Ne laissez pas l’unité ou la résine geler.
• Assurez-vous que la zone de travail est sufsamment drainée.
• Fermez l'alimentation en eau lorsque vous ne l'utilisez pas.
• Ne buvez pas l’eau produite par cet appareil.
1.2 AU DÉMARRAGE DU SYSTÈME:
• À utiliser uniquement avec de l'eau du robinet.
• Ne pas raccorder à un nettoyeur haute pression ni à une pompe auxiliaire.
• Ne dépassez pas la pression de l'eau de 90 psi.
• Vériez si le système comporte des ssures / dommages.
• Assurez-vous que le couvercle est complètement verrouillé.