Uplus Lighting 200 BLINDER User manual

User manual
200 BLINDER
Please read the instructions carefully before use

2
TABLE OF CONTENTS
1. Safety Instructions…………………………………………………………………………………3
2.Technical Specifications……………………………………………………………………………4
3.Control Menu …………………………………………………………………………………………4
4.DMX Channels ………………………………………………………………………………………5
5.Trouble Shooting……………………………………………………………………………………6
6.Fixture Cleaning………………………………………………………… …………………………6
STATEMENT
The product has well capability and intact packing when leave factory. All of the user should
comply with warning item and manual, any misuse cause of the damages are not included in our
guarantee, and also can not be responsible for any malfunction & problem owing to ignore the
manual.

3
1.Safety Instructions
Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that they also
receive this instruction booklet.
•Unpack and check carefully there is no transportation damage before using the unit.
•Before operating, ensure that the voltage and frequency of power supply match the power requirements of the
unit.
•It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
•The unit is for indoor use only. Use only in a dry location.
•The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent surfaces. Be sure
that no ventilation slots are blocked.
•Disconnect main power before replacement or servicing.
•Make sure there are no flammable materials close to the unit while operating as it is fire hazard.
•Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but always by taking its
base.
•Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is higher than this Unit
surface temperature may reach up to 85℃. DO NOT touch the housing bare-hand during its operation. Turn off
the power and allow about 15 minutes for the unit to cool down before replacing or serving.
•the event of serious operating problem, stop using the unit immediately.Never try to repair the unit by yourself.
Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest
authorized technical assistance center. Always use the same type spare parts.
•DO NOT touch any wire during operation as high voltage might be causing electric shock.
Warning:
•To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture.
•The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.
Caution:
•There are no user serviceable parts inside the unit. DO NOT open the housing or attempt any repairs yourself.
In the unlikely event your unit may require service, please contact your nearest dealer.
Installation:
•The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly fixed to
avoid vibration and slipping while operating. And make sure that the structure to which you are attaching the unit
is secure and is able to support a weight of 10 times of the unit’s weight. Also always use a safety cable that can
hold 12 times of the weight of the unit when installing the fixture.
•The equipment must be fixed by professionals. And it must be fixed at a place where is out of the touch of
people.

4
2.Technical Specifications
VOLTAGES:AC 100V-240V，50/60Hz
2*100W COB Blinder Light
Light source: 2*100W high bright COB LED
Color temperature:3200K/6500K
Beam Angle: 60゜
DMX Channel:4/8 CH
CONTROL:DMX512
WORK ENVIRONMENT TEMPERATURE: -10°C-40°C
Aluminum housing; IP20 indooor,
digital display
Good cooling system, over heat protection
NW:5 KGS
3.Control Menu
Operation method
No
Show
Function
Instruction
1
d001
DMX Address
(001~512)
DMX-512 address set, 4 Channels mode
2
A001
DMX Address
(001~512)
DMX-512 address set, 8 Channels mode
3
r255
Y1
(000~255)
UP、DOWN Change brightness
4
G255
W1
(000~255)
UP、DOWN Change brightness
5
b255
Y2
(000~255)
UP、DOWN Change brightness
6
u255
W2
(000~255)
UP、DOWN Change brightness
7
FH99
Strobe flash (01~99)
UP、DOWN Change the speed
8
CL01
Different Colors Output
(01~08)
UP、DOWN Change brightness
9
CC99
Colors Jump Change
(01~99)
UP、DOWN Change the speed
10
DE99
Colors Gradate
(01~99)
UP、DOWN Change the speed
11
CP99
Colors Pulse Change
(01~99)
UP、DOWN Change the speed
12
SU01
Colors sound-Active
(01~09)
UP、DOWN Change the effects

5
4.DMX Channels
DMX512Control： 8 Channel Model(A001)
CH
Display
Function
CH1
Dimmer
Y1、W1、Y2、W2 dimmer : from dark to bright
CH2
Y1 dimmer
Y1 dimmer : from dark to bright
CH3
W1 dimmer
W1 dimmer : from dark to bright
CH4
Y2 dimmer
Y2 dimmer : from dark to bright
CH5
W2 dimmer
W2 dimmer: from dark to bright
CH6
Strobe
Y1、W1、Y2、W2 strobe: from slow to fast
CH7
Function choice
0~50: DMX 8CH Control.
51~100: Different Colors Output
101~150: Colors Jump Change.
151~200: Colors Gradate.
201~250: Colors Pulse Change.
251~255: Sound-Active
CH8
Function speed
Speed function, from slow to fast
DMX512Control： 4Channel Model(D001)
Channel
Function
Instruction
CH1
Y1 dimmer
Dimmer- Dark to Bright
CH2
W1 dimmer
Dimmer- Dark to Bright
CH3
Y2 dimmer
Dimmer- Dark to Bright
CH4
W2 dimmer
Dimmer- Dark to Bright

6
5.Trouble Shooting
F ollo w ing a r e a few c o mm on p r oble m s th a t m a y occu r d uring ope r a tion . He r e a r e s o m e s ug g es tion s fo r
ea s y tr ou b leshooting :
A. The un it does no t work , no li ght a n d t he f a n d o es no t w o r k
1. Check th e c on nect ion of p owe r a nd m a in fu s e .
2. M eas ure th e m a ins volt a ge on th e m a i n co nn e ct o r .
3. Check th e pow er on LED .
B. N o t responding t o D MX c on t ro ll er
1. D M X LED s h ou ld b e on. If no t, che ck D M X co n nectors, ca b l es to s ee if link p r ope r ly .
2. If th e D M X LE D i s on a nd no r espons e t o th e c h a nn el, che ck th e a dd r ess s etti ng s a nd D M X
p ol a r ity .
3. If y ou h a ve i nter m ittent D M X s ig n a l p r oble m s , che ck th e p ins on c onn ecto r s or on
PCB of th e u nit or the p r ev iou s on e.
4. Tr y to us e a no th er D M X co ntroller .
5. Check if th e D M X ca b le s r un ne a r or run a lon g s id e t o h ig h volta ge c a b les th a t m a y c a us e d a m a ge or
in terfer ence to D M X inter face circui t.
C . One of the cha nn el s is no t w o r k ing w el l
1. Th e s tep p er moto r m ig h t b e dam a g ed or the c a b le c on nect ed to th e PCB is b r oken.
2. Th e m oto r ’ s d r ive IC on th e PCB m ig h t b e o ut of co ndition
6.Fixture Cleaning
The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates:
damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s optics.
Clean with soft cloth using normal glass cleaning fluid.
Always dry the parts carefully.
Clean the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.