Uplus Lighting 3010 IP PAR User manual

User manual
3010 IP PAR
Please read the instructions carefully before use

2
TABLE OF CONTENTS
1. Safety Instructions……………………………………………………………………………3
2.Technical Specifications………………………………………………………………………4
3.Control Menu ……………………………………………………………………………………5-6
4.DMX Channels ……………………………………………………………………………………6
5.Trouble Shooting…………………………………………………………………………………7
6.Fixture Cleaning………………………………………………………… ………………………7
STATEMENT
The product has well capability and intact packing when leave factory. All of the user should
comply with warning item and manual, any misuse cause of the damages are not included in our
guarantee, and also can not be responsible for any malfunction & problem owing to ignore the
manual.

3
1.Safety Instructions
Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that they also
receive this instruction booklet.
•Unpack and check carefully there is no transportation damage before using the unit.
•Before operating, ensure that the voltage and frequency of power supply match the power requirements of the
unit.
•It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
•The unit is for indoor use only. Use only in a dry location.
•The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent surfaces. Be sure
that no ventilation slots are blocked.
•Disconnect main power before replacement or servicing.
•Make sure there are no flammable materials close to the unit while operating as it is fire hazard.
•Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but always by taking its
base.
•Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is higher than this Unit
surface temperature may reach up to 85℃. DO NOT touch the housing bare-hand during its operation. Turn off
the power and allow about 15 minutes for the unit to cool down before replacing or serving.
•the event of serious operating problem, stop using the unit immediately.Never try to repair the unit by yourself.
Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest
authorized technical assistance center. Always use the same type spare parts.
•DO NOT touch any wire during operation as high voltage might be causing electric shock.
Warning:
•To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture.
•The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.
Caution:
•There are no user serviceable parts inside the unit. DO NOT open the housing or attempt any repairs yourself.
In the unlikely event your unit may require service, please contact your nearest dealer.
Installation:
•The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly fixed to
avoid vibration and slipping while operating. And make sure that the structure to which you are attaching the unit
is secure and is able to support a weight of 10 times of the unit’s weight. Also always use a safety cable that can
hold 12 times of the weight of the unit when installing the fixture.
•The equipment must be fixed by professionals. And it must be fixed at a place where is out of the touch of
people.

4
2.Technical Specifications
Input voltage: AC100-240V, 50/60Hz
Rated power: 300W
Light source: 30*10W high power LED (4 in 1 RGBW)
Channel:5/8 channels
Color mixing: RGBW color mixing, colorful infinite change
Strobe: 0-20Hz
Control: international standard DMX512
Lens angle: 25°
Display: OLED function menu with 4 buttons
Heat dissipation: intelligent temperature control, active
Maximum ambient temperature 40°C
Minimum ambient temperature -20°C
Maximum case temperature 65°C
Power connection IP65 Seetronic power connectors input/output
Data connection IP65 Seetronic DMX connectors input/output
LED life: 50,000-100,000 hours
Waterproof rating: IP65
Net weight: 7.6kg
Features:
4 dimming curves, high standard linear dimming
Exquisite die-cast aluminum housing, IP65 protection level, suitable for outdoor performances
Silent operation, no flicker output
Unique structure design, excellent natural heat dissipation effect
Double hanger design, convenient for air suspension and ground placement
DMX control, RDM intelligent control.
Features and advantages: Adopt waterproof sealing design, high color purity, special optical design,
more uniform light effect, waterproof grade IP65. Suitable for various indoor and outdoor
performances, environmental art lighting, outdoor lighting and other dyeing and lighting effects.

5
3.Control Menu
Display:
[MENU] menu selection or return to previous menu.
[UP] press [UP] through the menu list to increase/change the value of the current function.
[DOWN] press [DOWN] through the menu list to decrease/change the value of the current function.
[ENTER] confirm & quit out current function setting.
Display panel operation instruction
Menu
Sub-Menu
Description
DMX Address
A.(001-512)
DMX address 001-512
Mode
Manual
Manual Mode
DMX1
5CH Mode (default)
DMX2
8CH Mode
Auto
Auto Mode
Define
Define Mode
Color
Red
Red
Green
Green
Blue
Blue
Cold
Cold White
Pink
Pink
Yellow
Yellow
Cian
Cian
Amber
Amber
Warm
Warm White
White
Day White
Color fine
Red
0-255
Red color fine, 0-255
Green
0-255
Green color fine, 0-255
Blue
0-255
Blue color fine, 0-255
White
0-255
White color fine, 0-255
Dimmer
0-255
Dimmer,0-255
Strob
0-20
Strobe, 0-20, slow to fast
Auto prog
3 Auto color
T.(00-99)
3 colors change (0-99), Slow to fast
7 Auto color
T.(00-99)
7 colors change(0-99), Slow to fast
7 color fade
T.(00-99)
7 colors fade, 0-99, slow to fast
Strobe 1
T.(00-99)
Strobe 1 , 0-99, slow to fast
Strobe 2
T.(00-99)
Strobe 2 , 0-99, slow to fast
Display INV
0
Display Positive
180
Display Reverse
Display OFF
ON
Display keep ON

6
30s
Display OFF after 30s no operation
60s
Display OFF after 60s no operation
Reset
NO
No function
YES
Parameter restore to factory value
Info
RGBW/V1.8
Software version
4.DMX Channels
DMX channel´s functions and values (5 DMX channels):
DMX channel´s functions and values (8 DMX channels):
Channel
Function
DMX
Value
Description
1
Dimmer
0-255
Dimmer,0-100%
2
Red
0-255
Red dimming,0-100%
3
Green
0-255
Green dimming,0-100%
4
Blue
0-255
Blue dimming,0-100%
5
White
0-255
White dimming,0-100%
Channel
Function
DMX Value
Description
1
Dimmer
0-255
Dimmer,0-100%
2
Red
0-255
Red dimming,0-100%
3
Green
0-255
Green dimming,0-100%
4
Blue
0-255
Blue dimming,0-100%
5
White
0-255
White dimming,0-100%
6
Strobe
0-13
No function
14-255
Strobe from slow to fast
7
Auto Mode
0-9
No function
10-99
Color Macro(Hue), level 90
100-139
3 colors change
140-179
7 colors change
180-209
7 Colors Fade
210-229
7 Colors Strobe 1
230-255
7 Colors Strobe 2
8
Auto Speed
0-255
Auto speed, slow to fast

7
5.Trouble Shooting
F ollo w ing a r e a few c o mm on p r oble m s th a t m a y occu r d uring ope r a tion . He r e a r e s o m e s ug g es tion s fo r
ea s y tr ou b leshooting :
A. The un it does no t work , no li ght a n d t he f a n d o es no t w o r k
1. Check th e c on nect ion of p owe r a nd m a in fu s e .
2. M eas ure th e m a ins volt a ge on th e m a i n co nn e ct o r .
3. Check th e pow er on LED .
B. N o t responding t o D MX c on t ro ll er
1. D M X LED s h ou ld b e on. If no t, che ck D M X co n nectors, ca b l es to s ee if link p r ope r ly .
2. If th e D M X LE D i s on a nd no r espons e t o th e c h a nn el, che ck th e a dd r ess s etti ng s a nd D M X
p ol a r ity .
3. If y ou h a ve i nter m ittent D M X s ig n a l p r oble m s , che ck th e p ins on c onn ecto r s or on
PCB of th e u nit or the p r ev iou s on e.
4. Tr y to us e a no th er D M X co ntroller .
5. Check if th e D M X ca b le s r un ne a r or run a lon g s id e t o h ig h volta ge c a b les th a t m a y c a us e d a m a ge or
in terfer ence to D M X inter face circui t.
C . One of the cha nn el s is no t w o r k ing w el l
1. Th e s tep p er moto r m ig h t b e dam a g ed or the c a b le c on nect ed to th e PCB is b r oken.
2. Th e m oto r ’ s d r ive IC on th e PCB m ig h t b e o ut of co ndition
6.Fixture Cleaning
The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates:
damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s optics.
Clean with soft cloth using normal glass cleaning fluid.
Always dry the parts carefully.
Clean the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.