Uplus Lighting 100SPOT User manual

User manual
100 SPOT
Please read the instructions carefully before use

2
TABLE OF CONTENTS
1. Safety Instructions……………………………………………………………………………3-4
Technical Specifications…………………………………………………………………………4
Control Menu ……………………………………………………………………………………5-6
DMX Channels …………………………………………………………………………………6-8
Trouble Shooting…………………………………………………………………………………8
Fixture Cleaning………………………………………………………… ………………………9
STATEMENT
The product has well capability and intact packing when leave factory. All of the user should
comply with warning item and manual, any misuse cause of the damages are not included in our
guarantee, and also can not be responsible for any malfunction & problem owing to ignore the
manual.

3
1.Safety Instructions
Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that
they also receive this instruction booklet.
•Unpack and check carefully there is no transportation damage before using the unit.
•Before operating, ensure that the voltage and frequency of power supply match the power
requirements of the unit.
•It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
•The unit is for indoor use only. Use only in a dry location.
•The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent
surfaces. Be sure that no ventilation slots are blocked.
•Disconnect main power before replacement or servicing.
•Make sure there are no flammable materials close to the unit while operating as it is fire hazard.
•Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but always
by taking its base.
•Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is higher
than this Unit surface temperature may reach up to 85℃. DO NOT touch the housing bare-hand
during its operation. Turn off the power and allow about 15 minutes for the unit to cool down before
replacing or serving.
•the event of serious operating problem, stop using the unit immediately.Never try to repair the unit
by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please
contact the nearest authorized technical assistance center. Always use the same type spare parts.
•DO NOT touch any wire during operation as high voltage might be causing electric shock.
Warning:
•To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture.
•The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.
Caution:
•There are no user serviceable parts inside the unit. DO NOT open the housing or attempt any
repairs yourself. In the unlikely event your unit may require service, please contact your nearest
dealer.
Installation:
•The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly

4
fixed to avoid vibration and slipping while operating. And make sure that the structure to which you
are attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight. Also
always use a safety cable that can hold 12 times of the weight of the unit when installing the fixture.
•The equipment must be fixed by professionals. And it must be fixed at a place where is out of the
touch of people.
2.Technical Specifications
Input Voltage: 100-240V, 50/60Hz
Power consumption: 120W
Beam angle:8°
Light source: 100W White LED
Pan: 540°(16bit) Electric correction
Tilt：270° (16bit) Electric correction
Beam angle: 1.3°
Gobo:static gobo: 7gobo+open
Rotating gobo:6+open
Prism: 5 prism
Frost effect
Dimming:0-100% linear adjustment
DMX Channels:14 channels
Control mode:DMX512,Auto, Sound active, Master/slave
Dimension:260*200*310 mm; NW: 5.85KGS;GW:6.65KGS

5
3.Control Menu
set up
option
explain
running mode
DMX
From ver status: receiving DMX signal from control station or host
Go at a
slow pace
Random
walk
sound
control
DMX address
1~512
Press OK to enter the edit status.When selected, press "up" and "down"
keys to change the address code.Press OK again to select the ten
editors.Press OK again to select the single bit edit.Press the Exit Edit Status
once again
channel pattern
Standard
14CH
Standard 14-channel mode
RDM function
close
open
X reversal
close
open
Y reversal
close
open
XY exchange
close
open
Channel channel for XY axis (including fine tuning)
XY encoder
open
Use the encoder (optical coupling) to judge steps and automatically correct
the position
close
Correct the position without using the encoder (optical coupling)
There is no DMX
signal
keep
Continue running in the original state
zero
clearing
Motor back, stop operation
Screen protection
open
Turn off the backlight after 30 seconds of idle
close
Back light forever bright
Restore the default
settings
Press OK to see the confirmation dialog box, and press OK again, to restore
the default settings
System info

6
option
explain
software release
Current software version
DMX channel value
This enters the subinterface and displays channel values in value and percentage for
viewing
System error record
If the red ERR indicator shines, the lamp is running wrong, and the details can be viewed
into the subinterface.After viewing, press Clear to empty the error record
Note: Sometimes it is not really a Hall or optical coupling installation problem, but a
reverse motor wiring
error message
explain
Motor reset failed,
serial port error
Drive board did not respond.The serial port communication line connecting the display
board and the drive board is faulty, or with the drive board is.
X-axis reset failed
X axis photoelectric switch, or X axis motor problem
The reduction of the
Y axis failed
Y-axis photoelectric switch, or Y-axis motor problem
X-axis Hall error"
Problem with the X-axis Hall
The Y-axis Hall error
There are problems with the Y-axis Hall
Color disk reset
failed
Color disc Hall, or the color disc motor has a problem
Pattern disk reset
failed
Patterned disc Hall, or the patterned disc motor has a problem
The focus reset
failed
Focus Hall, or have problems with the focusing motor
Bulb control failed
bubble or bubble failure, there is a problem with the lighter or bulb
Senior
option
explain
Reset calibration
After entering the sub-interface, the reset position of X-axis and Y-axis motors can be
adjusted to make up for the error in hardware installation. The adjustment range
is-128~ + 127. + 0 indicates no adjustment.
Sensor monitoring
Real-time monitoring of various photoelectric switches, hall and other sensors on the
lamp status
4.DMX Channels
CH14
CH
Function
Value
Effect
1
Dimmer
000-255
Dimmer from dark to light
2
Strobe
000-255
Strobe from slow to fast
3
Pan
000-255
Pan
4
Tilt
000-255
Tilt
5
XY speed
000-255
Speed from fast to slow
6
Color
000 - 004
005 - 009
010 - 014
015 - 019
white
color 1
color 2
color 3

7
6
color
020 - 024
025 - 029
030 - 034
035 - 039
040 - 044
045 - 049
050 - 054
055 - 059
060 - 064
065 - 069
070 - 074
075 - 079
080 - 255
color 4
color 5
color 6
color 7
White+color 1
color 1+color 2
color 2+color 3
color 3+color 4
color 4+color 5
color 5+color 6
color 6+color 7
color 7+white
Slow rotation -Fast rotation
7
GOBO
000-009
010-019
020-029
030-039
040-049
050-059
060-069
070-079
080-128
129
130-134
135
136-220
221-225
……
250-255
White
GOBO1
GOBO2
GOBO3
GOBO4
GOBO5
GOBO6
GOBO7
FAST rotation
Slow rotation
Stop
Slow rotation
FAST rotation
GOBO1 shake,slow to fast
……
GOBO7 shake,slow to fast
8
Gobo1
000 - 009
010 - 019
020 - 029
030 - 039
040 - 049
050 - 059
060 - 069
070
……
129
130 - 134
135
……
225
226 - 230
……
251 - 255
White
Gobo1
Gobo2
Gobo3
Gobo4
Gobo5
Gobo6
FAST rotation
……
Slow rotation
Stop
Slow rotation
……
FAST rotation
Gobo1 shake,slow to fast
……
Gobo6 shake,slow to fast
9
GOBO 1 RT
000-063
Position

8
9
GOBO 1 RT
64
……
127
128
……
190
191-192
193
……
255
Slow rotation
……
FAST rotation
FAST rotation
……
Slow rotation
Stop
Slow rotation
……
FAST rotation
10
Prism
000-009
010-014
15
……
255
Remove the Prism
Insert prism
Prism slow rotation
……
Prism fast rotation
11
focus
000-255
12
Pan fine
000 - 255
Pan fine
13
Tilt fine
000 - 255
Tilt fine
14
Reset
000-127
128-255
None, there is no action for the area without the specified function
Reset all motors
5.Trouble Shooting
F ollo w ing a r e a few c o mm on p r oble m s th a t m a y occu r d uring ope r a tion . He r e a r e s o m e s ug g es tion s fo r
ea s y tr ou b leshooting :
A. The un it does no t work , no li ght a n d t he f a n d o es no t w o r k
1. Check th e c on nect ion of p owe r a nd m a in fu s e .
2. M eas ure th e m a ins volt a ge on th e m a i n co nn e ct o r .
3. Check th e pow er on LED .
B. N o t responding t o D MX c on t ro ll er
1. D M X LED s h ou ld b e on. If no t, che ck D M X co n nectors, ca b l es to s ee if link p r ope r ly .
2. If th e D M X LE D i s on a nd no r espons e t o th e c h a nn el, che ck th e a dd r ess s etti ng s a nd D M X p ol a r ity .
3. If y ou h a ve i nter m ittent D M X s ig n a l p r oble m s , che ck th e p ins on c onn ecto r s or on
PCB of th e u nit or the p r ev iou s on e.
4. Tr y to us e a no th er D M X co ntroller .
5. Check if th e D M X ca b le s r un ne a r or run a lon g s id e t o h ig h volta ge c a b les th a t m a y c a us e d a m a ge or
in terfer ence to D M X inter face circui t.
C . One of the cha nn el s is no t w o r k ing w el l
1. Th e s tep p er moto r m ig h t b e dam a g ed or the c a b le c on nect ed to th e PCB is b r oken.
2. Th e m oto r ’ s d r ive IC on th e PCB m ig h t b e o ut of co ndition

9
6.Fixture Cleaning
The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp,
smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s optics.
Clean with soft cloth using normal glass cleaning fluid.
Always dry the parts carefully.
Clean the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.