Uplus Lighting LED PROFILE MZ User manual

User manual
LED PROFILE MZ
Please read the instructions carefully before use

2
TABLE OF CONTENTS
1. Safety Instructions……………………………………………………………………………3
2.Technical Specifications………………………………………………………………………4
3.Descriptions………………………………………………………………………………………5
4.Unpacking…………………………………………………………………………………………5
5.Control Menu ……………………………………………………………………………………6-7
6.DMX Channels ……………………………………………………………………………………7
7.Dimension …………………………………………………………………………………………8
8.Trouble Shooting…………………………………………………………………………………9
9.Fixture Cleaning………………………………………………………… ………………………9
STATEMENT
The product has well capability and intact packing when leave factory. All of the user should
comply with warning item and manual, any misuse cause of the damages are not included in our
guarantee, and also can not be responsible for any malfunction & problem owing to ignore the
manual.

3
1.Safety Instructions
Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that they also
receive this instruction booklet.
•Unpack and check carefully there is no transportation damage before using the unit.
•Before operating, ensure that the voltage and frequency of power supply match the power requirements of the
unit.
•It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
•The unit is for indoor use only. Use only in a dry location.
•The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent surfaces. Be sure
that no ventilation slots are blocked.
•Disconnect main power before replacement or servicing.
•Make sure there are no flammable materials close to the unit while operating as it is fire hazard.
•Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but always by taking its
base.
•Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is higher than this Unit
surface temperature may reach up to 85℃. DO NOT touch the housing bare-hand during its operation. Turn off
the power and allow about 15 minutes for the unit to cool down before replacing or serving.
•the event of serious operating problem, stop using the unit immediately.Never try to repair the unit by yourself.
Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest
authorized technical assistance center. Always use the same type spare parts.
•DO NOT touch any wire during operation as high voltage might be causing electric shock.
Warning:
•To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture.
•The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.
Caution:
•There are no user serviceable parts inside the unit. DO NOT open the housing or attempt any repairs yourself.
In the unlikely event your unit may require service, please contact your nearest dealer.
Installation:
•The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly fixed to
avoid vibration and slipping while operating. And make sure that the structure to which you are attaching the unit
is secure and is able to support a weight of 10 times of the unit’s weight. Also always use a safety cable that can
hold 12 times of the weight of the unit when installing the fixture.
•The equipment must be fixed by professionals. And it must be fixed at a place where is out of the touch of
people.

4
2.Technical Specifications
Light Source:
LED POWER: 200W
LED Color: CW or WW (200W) COB LED
Color Rendering Index(CRI): Ra≥90
Power supply:
Voltage: AC100-240V
Max.power: 200W
Optics:
Beam Angle: 12°to 30° or 25°to 50°
LED Life Time: over 50,000 hours
Iris: optional
Color Frame: optional
Features:
Dimming Curve: 4 kinds dimming curve
PWM: 500HZ - 25000HZ optional
Strobe :1-25times/sec
Light body feature:
Focus: Can be adjusted by hand
Technology: High-quality optical system , glass reflector
Light body: Die casting Aluminum
Touch screen: LCD with touch screen
Feature of housing: High quality fireproof ,corrosion-resistance, Oxidation resistance
Control:
Control Protocol: RDM / DMX
Control System: DMX, Auto run and Master/Slave
DMX Channels: 1/2CH
Working Environment :
Working Temperature: -30~40℃
Cooling system: No noise fan (copper tube)
IP Grade: IP20
Package :
Dimensions: 738(D)*187(W)*436(H)mm
Net Weight : 10.5kgs
Gross Weight: 12.5 kgs
Packing Size: 72*33*31.5 cm (1pc/carton)

5
3.Descriptions
·Warm or cool white ERS style fixture with output exceeding a tungsten 750 W source
·Manual zoom range 12°to 30° or 25°to 50°
·Ultra smooth 16-bit dimming of master dimmer and individual colors
·Flat, even field of light with superior color mixing
·RDM (Remote Device Management) for added flexibility
·Adjustable PWM (Pulse Width Modulation) to avoid flickering on camera
·Selectable dimming curve: Standard mode, Incandescent mode, quick mode and linear mode
·LCD touch screen
·Virtually silent operation for use in studio and theatre applications
4.Unpacking
Thank you for choosing our LED PROFILE MZ. For your own safety, please read this manual before installing the
device. This manual covers the important information on installation and applications. Please install and operate
the fixture with following instructions. Meanwhile, please keep this manual well for future needs.
The LED PROFILE MZ is made of a new type of high temperature strength of die cast aluminum casing with nice
outlook. The fixture is designed and manufactured strictly following CE&RoHS standards, complying with
international standard DMX512 protocol. It's available independently controlled and linkable with each other for
operation. And it is applicable for large-scale live performances, theater, studio, nightclubs and discos.
The LED PROFILE MZ adopts 1PCS 200W COB LED (available for WW) which features high brightness and
stability. Please carefully unpack it when you receive the fixture and check whether it is damaged during the
transportation. And please check whether the following items are included

6
5.Control Menu
Operation Status
Mode
Display
Description
DMX Mode
Axxx
“A”stand for standard channel mode,，“xxx”stand for ID address
Dxxx
“D”stand for basic channel mode，“xxx”stand for ID address
Manual
Mode
S-MC
“S”stand for stand alone mode，“MC”stand for“Mixed Color”
DMX Settings
Menu
Operation
Option
Description
DMXStartAddress
Press key of “OK” enter to edit mode, press “UP”
and ”down” to edit the DMX address
1~512
DMX Profile
Press key of “OK” change the DMX channel mode
2CH
Standard Channel
Mode
1CH
Basic Channel Mode
Single Mode Choice
Menu
Operation
Vice Menu description
White Point
Press Key of “OK” to choose mode
Choose color temperature
Quick Color
Same as before
Choose inner setting color
Mixed Color
Same as before
Choose the color and strobe setting
Status
Menu
Description
Software
Name of software
Version
Version
Temperature
Show the temperature of lighting fixture
DMX Status
With“OK”（Slavemode，with signal），“NONE”（Slavemode，nosignal）、 “Alone”
（alone）

7
Settings
Menu
Operation
Option
Description
Touch Screen
Calibration
Touch screen adjust
Dimmer Frequency
Change the dimmer
frequency
500HZ
……
Each 100HZ for increase or decrease
25000HZ
Dimmer Curve
Change dimmer
curve
Standard
Incandescent
Linear
Quick
Over Temperature
Temperature setting
45~95
Each 5 for increase or decrease
Backlight
Adjust the display
brightness
10%~100%
Each 5% for increase or decrease
Backlight Timeout
Screen protect
setting
No screen protect or
black screen from 0~60
second
Each 5 for increase or decrease
Load Factory Settings
Reset
6.DMX Channels
Model – CH2
Channel
Data
Function
Remark
1
0~255
Dimmer
2
0~10
No function
11~255
Strobe speed（255 is the fastest）
Model – CH1
Channel
Data
Function
1
0~255
Color 1

8
7.Dimension
Size of the fixture:
12-30°：860(L)MM*180(W)MM*440(H)MM
25-50°：740(L)MM*180(W)MM*440(H)MM

9
8.Trouble Shooting
F ollo w ing a r e a few c o mm on p r oble m s th a t m a y occu r d uring ope r a tion . He r e a r e s o m e s ug g es tion s fo r
ea s y tr ou b leshooting :
A. The un it does no t work , no li ght a n d t he f a n d o es no t w o r k
1. Check th e c on nect ion of p owe r a nd m a in fu s e .
2. M eas ure th e m a ins volt a ge on th e m a i n co nn e ct o r .
3. Check th e pow er on LED .
B. N o t responding t o D MX c on t ro ll er
1. D M X LED s h ou ld b e on. If no t, che ck D M X co n nectors, ca b l es to s ee if link p r ope r ly .
2. If th e D M X LE D i s on a nd no r espons e t o th e c h a nn el, che ck th e a dd r ess s etti ng s a nd D M X
p ol a r ity .
3. If y ou h a ve i nter m ittent D M X s ig n a l p r oble m s , che ck th e p ins on c onn ecto r s or on
PCB of th e u nit or the p r ev iou s on e.
4. Tr y to us e a no th er D M X co ntroller .
5. Check if th e D M X ca b le s r un ne a r or run a lon g s id e t o h ig h volta ge c a b les th a t m a y c a us e d a m a ge or
in terfer ence to D M X inter face circui t.
C . One of the cha nn el s is no t w o r k ing w el l
1. Th e s tep p er moto r m ig h t b e dam a g ed or the c a b le c on nect ed to th e PCB is b r oken.
2. Th e m oto r ’ s d r ive IC on th e PCB m ig h t b e o ut of co ndition
9.Fixture Cleaning
The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates:
damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s optics.
Clean with soft cloth using normal glass cleaning fluid.
Always dry the parts carefully.
Clean the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.