Uplus Lighting COB400 ZOOM User manual

User manual
COB400 ZOOM
Please read the instructions carefully before use

2
TABLE OF CONTENTS
1. Safety Instructions……………………………………………………………………………3-4
2.Technical Specifications…………………………………………………………………………4
3.Control Menu ………………………………………………………………………………………5
4.DMX Channels ……………………………………………………………………………………6
5.Trouble Shooting…………………………………………………………………………………6
6.Fixture Cleaning………………………………………………………… ………………………7
STATEMENT
The product has well capability and intact packing when leave factory. All of the user should
comply with warning item and manual, any misuse cause of the damages are not included in our
guarantee, and also can not be responsible for any malfunction & problem owing to ignore the
manual.

3
1.Safety Instructions
Please keep this User Guide for future consultation. If you sell the unit to another user, be sure
that they also receive this instruction booklet.
•Unpack and check carefully there is no transportation damage before using the unit.
•Before operating, ensure that the voltage and frequency of power supply match the power
requirements of the unit.
•It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
•The unit is for indoor use only. Use only in a dry location.
•The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent
surfaces. Be sure that no ventilation slots are blocked.
•Disconnect main power before replacement or servicing.
•Make sure there are no flammable materials close to the unit while operating as it is fire hazard.
•Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but always
by taking its base.
•Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is higher
than this Unit surface temperature may reach up to 85℃. DO NOT touch the housing bare-hand
during its operation. Turn off the power and allow about 15 minutes for the unit to cool down before
replacing or serving.
•the event of serious operating problem, stop using the unit immediately.Never try to repair the unit
by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please
contact the nearest authorized technical assistance center. Always use the same type spare parts.
•DO NOT touch any wire during operation as high voltage might be causing electric shock.
Warning:
•To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture.
•The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.
Caution:
•There are no user serviceable parts inside the unit. DO NOT open the housing or attempt any
repairs yourself. In the unlikely event your unit may require service, please contact your nearest
dealer.
Installation:
•The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is

4
firmly fixed to avoid vibration and slipping while operating. And make sure that the structure to
which you are attaching the unit is secure and is able to support a weight of 10 times of the unit’s
weight. Also always use a safety cable that can hold 12 times of the weight of the unit when
installing the fixture.
•The equipment must be fixed by professionals. And it must be fixed at a place where is out of the
touch of people.
2.Technical Specifications
VOLTAGES:AC 100V-240V，50/60Hz
POWER CONSUMPTION:450W@230V
Light Source: 400W White COB Led
Quantity: 1pcs
Color Wheel: 4 colors and Open （R+G+B+WW）or CTO Color temperature 2800-6000K(Selectable)
DIMMER:0-100% mechanical dimming, free dimming available, macro control
STROBE: （Optional）
Electronic Strobe 0 -25F.P.S
IP RATE:IP20 Indoor
BEAM ANGLE: 6-50°
CONTROL:DMX512, 3 pins interfaces RDM Control Protocol
Channel mode: 10 Channel
Pan scan：540°(16bit) Electric correction
Tilt scan：270° (16bit) Electric correction
Control Mode:DMX512 / Master-Slave / Auto
HOUSING:Cast aluminum, IP20 Indoor
WORK ENVIRONMENT TEMPERATURE: -10°C-40°C
Dimension: 300 * 220 * 470mm;
Net weight : 9.7Kg
Carton Size: 60*41*34cm

5
3.Control Menu
Operation method
touch
wheel
function
Up
turn left
option/edit
down
turn right
option/edit
OK / Enter
press the wheel
Executive start / exit
return
when return menu ,press the wheel
return previous page
Set ”Modify address code” as an example, tell about the using of the touch.
1. Touch button “setting” in the main interface, and then into “setting” interface.
2. The 4 touch button in the right, are “up”, “ok”, “down”, “back”.
3. Press “up” or “down” button select “DMX address”.
4. Press “ok” button into editing state.
5. Press “up” button or “ down” button modification address code (using the new address immedi
ately and autosave)
6.Press “OK” button out of the editing state ( could omitted)
7. Press “back” button back to the main menu.
If using the wheel, process like bellow :
1. In the main interface , turn the wheel, select “setting” button.
2. Press the turn wheel and then loosen, into “setting” interface.
3.In the “setting” interface, select “DMX address”
4. Press the turn wheel and then loosen, into the editing state.
5. Turn the wheel, modification address code
6. After modification, press turn wheel and then loosen, out of the editing state.
7. Turn the wheel select “back”, press turn wheel and then loosen, back into the main interface.

6
4.DMX Channels
10 Channel mode
Channel
Name
DMX Value
Description
1
Pan
0-255
Pan Movement
2
Pan Fine
0-255
Pan Fine
3
Tilt
0-255
Tilt Movement
4
Tilt Fine
0-255
Tilt Fine
5
P/T SPEED
0-255
P/T SPEED
6
ZOOM
0-255
ZOOM
7
CTO
0-255
Change Color temperature (2600-6500K)
8
Dimmer
0-255
Dimmer from dark to bright
9
STROBE
0-5
OPEN
6-10
CLOSED
252-255
STROBE FORM SLOW TO FAST
10
RESET
250-255
Reset after 3 seconds
5.Trouble Shooting
F ollo w ing a r e a few c o mm on p r oble m s th a t m a y occu r d uring ope r a tion . He r e a r e s o m e s ug g es tion s fo r
ea s y tr ou b leshooting :
A. The un it does no t work , no li ght a n d t he f a n d o es no t w o r k
1. Check th e c on nect ion of p owe r a nd m a in fu s e .
2. M eas ure th e m a ins volt a ge on th e m a i n co nn e ct o r .
3. Check th e pow er on LED .
B. N o t responding t o D MX c on t ro ll er
1. D M X LED s h ou ld b e on. If no t, che ck D M X co n nectors, ca b l es to s ee if link p r ope r ly .
2. If th e D M X LE D i s on a nd no r espons e t o th e c h a nn el, che ck th e a dd r ess s etti ng s a nd D M X
p ol a r ity .
3. If y ou h a ve i nter m ittent D M X s ig n a l p r oble m s , che ck th e p ins on c onn ecto r s or on
PCB of th e u nit or the p r ev iou s on e.
4. Tr y to us e a no th er D M X co ntroller .
5. Check if th e D M X ca b le s r un ne a r or run a lon g s id e t o h ig h volta ge c a b les th a t m a y c a us e d a m a ge or
in terfer ence to D M X inter face circui t.
C . One of the cha nn el s is no t w o r k ing w el l
1. Th e s tep p er moto r m ig h t b e dam a g ed or the c a b le c on nect ed to th e PCB is b r oken.
2. Th e m oto r ’ s d r ive IC on th e PCB m ig h t b e o ut of co ndition

7
6.Fixture Cleaning
The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates:
damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s optics.
Clean with soft cloth using normal glass cleaning fluid.
Always dry the parts carefully.
Clean the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.