Uplus Lighting 37X15ZWASH User manual

User manual
37X15Z WASH
Please read the instructions carefully before use

2
TABLE OF CONTENTS
1. Safety Instructions……………………………………………………………………………3-4
Technical Specifications…………………………………………………………………………4
Control Menu ……………………………………………………………………………………4-5
DMX Channels ……………………………………………………………………………………6-8
Trouble Shooting…………………………………………………………………………………8
Fixture Cleaning………………………………………………………… ………………………9
STATEMENT
The product has well capability and intact packing when leave factory. All of the user should
comply with warning item and manual, any misuse cause of the damages are not included in our
guarantee, and also can not be responsible for any malfunction & problem owing to ignore the
manual.

3
1.Safety Instructions
Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that
they also receive this instruction booklet.
•Unpack and check carefully there is no transportation damage before using the unit.
•Before operating, ensure that the voltage and frequency of power supply match the power
requirements of the unit.
•It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
•The unit is for indoor use only. Use only in a dry location.
•The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent
surfaces. Be sure that no ventilation slots are blocked.
•Disconnect main power before replacement or servicing.
•Make sure there are no flammable materials close to the unit while operating as it is fire hazard.
•Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but always
by taking its base.
•Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is higher
than this Unit surface temperature may reach up to 85℃. DO NOT touch the housing bare-hand
during its operation. Turn off the power and allow about 15 minutes for the unit to cool down before
replacing or serving.
•the event of serious operating problem, stop using the unit immediately.Never try to repair the unit
by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please
contact the nearest authorized technical assistance center. Always use the same type spare parts.
•DO NOT touch any wire during operation as high voltage might be causing electric shock.
Warning:
•To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture.
•The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.
Caution:
•There are no user serviceable parts inside the unit. DO NOT open the housing or attempt any
repairs yourself. In the unlikely event your unit may require service, please contact your nearest
dealer.
Installation:
•The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly

4
fixed to avoid vibration and slipping while operating. And make sure that the structure to which you
are attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight. Also
always use a safety cable that can hold 12 times of the weight of the unit when installing the fixture.
•The equipment must be fixed by professionals. And it must be fixed at a place where is out of the
touch of people.
2.Technical Specifications
Power supply: 110-240V, 50/60HZ
Power consumption: 560W
Light source:37*15W 4in1 RGBW LED
DMX Channel: 37CH1 /21CH2 /15CH3/12CH4 / 37CH5
Zoom angle: 4°-60°
Horizontal scanning: 540° (16bit precision scanning) Electronic error correction
Vertical scanning: 270° (16bit precision scanning) Electronic error correction
Strobe: 1-25 times/S or random strobe
Dimming: 0-100% linear adjustment
Dimension: 42*33*26 cm, NW:13.5 kgs
Led ring control effect
3.Control Menu
Menu Operation
On the base of the control panel offers a number of features, such as setting DMX fixture address,
switch the lamp, run the test program, the mode selection.

5

6
4.DMX Channels
CH Mode
Mode/Channel
Value
Function
Type of control
1
2
3
4
5
1
1
1
1
1
0--255
Pan(8bit)
Pan movement
Proportional
2
2
2
2
2
0--255
Pan(16bit)
Fine control of pan movement
Proportional
3
3
3
3
3
0--255
Tilt(8bit)
Tilt movement
Proportional
4
4
4
4
4
0--255
Tilt(16bit)
Fine control of tilt movement
Proportional
5
5
5
5
5
0--255
Pan/Tilt speed
Proportional
6
6
6
6
6
0--49
Reserved
To activate following functions,stop in DMX value
for at least 3sec,and shutter must be closed at
least 3sec.(Shutter channel 35/19/14/9 must be
at range of 0-31DMX).Corresponding menu
items are temporaily overrided
50--59
Pan/Tilt speed
step
60--69
Pan/Tilt time mode
step
70--79
Blackout while pan/tilt moving
step
80--89
Disabled blackout while pan/tilt moving
step
90--139
Reserved
To activate following reset function,stop in DMX
value for at least 3 sec.
140--149
Pan/Tilt reset
step
150--179
Reserved
180--189
Zoom reset
step
190--199
Reserved
200--209
Total reset
step
210--255
Reserved
-
7
7
7
-
0--255
Red (8bit)-all arrays
Proportional
-
8
-
-
-
0--255
Red fine(16 bit)-all arrays
Proportional
-
9
8
8
-
0--255
Green (8bit)-all arrays
Proportional
-
10
-
-
-
0--255
Green fine(16 bit)-all arrays
Proportional
-
11
9
9
-
0--255
Blue (8bit)-all arrays
Proportional
-
12
-
-
-
0--255
Blue fine(16 bit)-all arrays
Proportional
-
13
10
10
-
0--255
White (8bit)-all arrays
Proportional
-
14
-
-
-
0--255
White fine(16 bit)-all arrays
Proportional
7
-
-
-
14
0--255
Red (8bit)-LED array 1
Proportional

7
8
-
-
-
15
0--255
Red fine(16 bit) array 1
Proportional
9
-
-
-
16
0--255
Green (8bit) array 1
Proportional
10
-
-
-
17
0--255
Green fine(16 bit) array 1
Proportional
11
-
-
-
18
0--255
Blue (8bit) array 1
Proportional
12
-
-
-
19
0--255
Blue fine(16 bit) array 1
Proportional
13
-
-
-
20
0--255
White (8bit) array 1
Proportional
14
-
-
-
21
0--255
White fine(16 bit) array 1
Proportional
15
-
-
-
22
0--255
Red (8bit) array 2
Proportional
16
-
-
-
23
0--255
Red fine(16 bit) array 2
Proportional
17
-
-
-
24
0--255
Green (8bit) array 2
Proportional
18
-
-
-
25
0--255
Green fine(16 bit) array 2
Proportional
19
-
-
-
26
0--255
Blue (8bit) array 2
Proportional
20
-
-
-
27
0--255
Blue fine(16 bit) array 2
Proportional
21
-
-
-
28
0--255
White (8bit) array 2
Proportional
22
-
-
-
29
0--255
White fine(16 bit) array 2
Proportional
23
-
-
-
30
0--255
Red (8bit) array 3
Proportional
24
-
-
-
31
0--255
Red fine(16 bit) array 3
Proportional
25
32
0--255
Green (8bit) array 3
Proportional
26
33
0--255
Green fine(16 bit) array 3
Proportional
27
34
0--255
Blue (8bit) array 3
Proportional
28
35
0--255
Blue fine(16 bit) array 3
Proportional
29
36
0--255
White (8bit) array 3
Proportional
30
37
0--255
White fine(16 bit) array 3
Proportional
31
15
11
11
12
0
CTC
Full output power on all LEDS
step
1-255
Colour temperature correction from cool to warm
Proportional
32
16
12
-
13
0
No function
1--3
White 2700K
step
4--6
White 3200K
step
7--9
White 4200K
step
10--12
White 5600K
step
13--15
White 8000K
step
16
Blue (blue=full,red+green+white=0)
step
17--55
Red=0,Green->up,Blue=full,White=0
Proportional
56
Light Blue(Red=0,Green=full,Blue=full,White=0)
step
57--95
Red=0,Green=full,Blue->down,White=0
Proportional
96
Green(Red=0,Green=full,Blue=0,White=0)
step
97--134
Red->up,Green=full,Blue=0,White=0
Proportional
135
Yellow(Red=full,Green=full,Blue=0,White=0)
step
136--174
Red=full,Green->down,Blue=0,White=0
Proportional
175
Red(Red=full,Green=0,Blue=0,White=0)
step
176--214
Red=full,Green=0,Blue->up,White=0
Proportional
215
Magenta(Red=full,Green=0,Blue=full,White=0)
step
216-254
Red->down,Green=0,Blue=full,White=0
Proportional
255
Blue(Red=0,Green=0,Blue=full,White=0
step
33
17
13
12
7
0--255
Zoom(8bit)
Proportional

8
34
18
-
-
8
0--255
Zoom fine(16bit)
Proportional
35
19
14
-
9
0--31
Shutter closed
step
32--63
Shutter open
step
64--95
Strobe-effect from slow to fast
Proportional
96--127
Shutter open
step
128--143
Opening pulses in sequences from slow to fast
Proportional
144--159
Closing pulses in sequences from fast to slow
Proportional
160--191
Shutter open
step
192--223
Random strobe-effects from slow to fast
Proportional
224--255
Shutter open
step
36
20
15
-
10
0--255
Dimmer(8bit)
Proportional
37
21
-
-
11
0--255
Dimmer fine (16bit)
Proportional
5.Trouble Shooting
F ollo w ing a r e a few c o mm on p r oble m s th a t m a y occu r d uring ope r a tion . He r e a r e s o m e s ug g es tion s fo r
ea s y tr ou b leshooting :
A. The un it does no t work , no li ght a n d t he f a n d o es no t w o r k
1. Check th e c on nect ion of p owe r a nd m a in fu s e .
2. M eas ure th e m a ins volt a ge on th e m a i n co nn e ct o r .
3. Check th e pow er on LED .
B. N o t responding t o D MX c on t ro ll er
1. D M X LED s h ou ld b e on. If no t, che ck D M X co n nectors, ca b l es to s ee if link p r ope r ly .
2. If th e D M X LE D i s on a nd no r espons e t o th e c h a nn el, che ck th e a dd r ess s etti ng s a nd D M X p ol a r ity .
3. If y ou h a ve i nter m ittent D M X s ig n a l p r oble m s , che ck th e p ins on c onn ecto r s or on
PCB of th e u nit or the p r ev iou s on e.
4. Tr y to us e a no th er D M X co ntroller .
5. Check if th e D M X ca b le s r un ne a r or run a lon g s id e t o h ig h volta ge c a b les th a t m a y c a us e d a m a ge or
in terfer ence to D M X inter face circui t.
C . One of the cha nn el s is no t w o r k ing w el l
1. Th e s tep p er moto r m ig h t b e dam a g ed or the c a b le c on nect ed to th e PCB is b r oken.
2. Th e m oto r ’ s d r ive IC on th e PCB m ig h t b e o ut of co ndition

9
6.Fixture Cleaning
The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp,
smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s optics.
Clean with soft cloth using normal glass cleaning fluid.
Always dry the parts carefully.
Clean the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.