Uplus Lighting IR 1210 PAR User manual

User manual
IR 1210 PAR
Please read the instructions carefully before use

2
TABLE OF CONTENTS
1. Safety Instructions……………………………………………………………………………3-4
Technical Specifications…………………………………………………………………………4
Control Menu ………………………………………………………………………………………5
DMX Channels ……………………………………………………………………………………6
Dimension …………………………………………………………………………………………6
Trouble Shooting…………………………………………………………………………………7
Fixture Cleaning………………………………………………………… ………………………7
STATEMENT
The product has well capability and intact packing when leave factory. All of the user should
comply with warning item and manual, any misuse cause of the damages are not included in our
guarantee, and also can not be responsible for any malfunction & problem owing to ignore the
manual.

3
1.Safety Instructions
Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that
they also receive this instruction booklet.
•Unpack and check carefully there is no transportation damage before using the unit.
•Before operating, ensure that the voltage and frequency of power supply match the power
requirements of the unit.
•It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
•The unit is for indoor use only. Use only in a dry location.
•The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent
surfaces. Be sure that no ventilation slots are blocked.
•Disconnect main power before replacement or servicing.
•Make sure there are no flammable materials close to the unit while operating as it is fire hazard.
•Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but always
by taking its base.
•Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is higher
than this Unit surface temperature may reach up to 85℃. DO NOT touch the housing bare-hand
during its operation. Turn off the power and allow about 15 minutes for the unit to cool down before
replacing or serving.
•the event of serious operating problem, stop using the unit immediately.Never try to repair the unit
by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please
contact the nearest authorized technical assistance center. Always use the same type spare parts.
•DO NOT touch any wire during operation as high voltage might be causing electric shock.
Warning:
•To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture.
•The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.
Caution:
•There are no user serviceable parts inside the unit. DO NOT open the housing or attempt any
repairs yourself. In the unlikely event your unit may require service, please contact your nearest
dealer.
Installation:

4
•The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly
fixed to avoid vibration and slipping while operating. And make sure that the structure to which you
are attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight. Also
always use a safety cable that can hold 12 times of the weight of the unit when installing the fixture.
•The equipment must be fixed by professionals. And it must be fixed at a place where is out of the
touch of people.
2.Technical Specifications
Voltage: AC100-240V, 50/60Hz
Power: 130W
Light Source: 12X10W RGBW 4in1 ultra bright LED
Lifespan: around 50,000-100,000 hours
Control: DMX 512,4/8 channels
Control mode: DMX 512, Auto mode, Master/Slave Mode,Sound Mode, Remote control
Display: LED display with 4 buttons
Heat dissipation: intelligent temperature control, no fan,no noise
Power connection: Power con connectors input/output
Data connection: 3-pin DMX connectors input/output
LED life: 50,000-100,000 hours
IP rating: IP20
Beam angle: 25 º
Net Weight：2.6KG

5
3.Control Menu
[MENU] menu selection or return to previous menu.
[UP] press [UP] through the menu list to increase/change the value of the current function.
[DOWN] press [DOWN] through the menu list to decrease/change the value of the current function.
[ENTER] confirm & quit out current function setting.
Menu
Function
A001
A001—A512
DMX Address 001-512
Chnd
4CH
4 channels mode
8CH
8 channels mode
CL01
CL01—CL15
15 static color mixing modes, color selection by up and down keys
Strobe mode St00-St16 after confirmation, adjust by up and down keys
CC99
CC01-CC99
Color Change, Speed from slow to fast (01-99)
EE99
EE01-EE99
Color Pulse,Speed from slow to fast (01-99)
FF99
FF01-FF99
Color Gradient,Speed from slow to fast (01-99)
ST99
ST01-ST99
Strobe, 01-99
SOU1
SOU1
Sound mode 1
SOU2
Sound mode 2
SOU3
Sound mode 3
SOU4
Sound mode 4
IRCL
ON/OFF
Remote control ON/OFF
R255
R000-R255
R manual dimming
G255
G000-G255
G manual dimming
B255
B000-B255
B manual dimming
W255
W000-W255
W manual dimming
T000
OFF/70-100
Display current temperature

6
4.DMX Channels
4 CH Mode
Channel
Function
DMX Value
Description
CH1
R Dimmer
0-255
Red dimming from dark to bright
CH2
G Dimmer
0-255
Green dimming from dark to bright
CH3
B Dimmer
0-255
Blue dimming from dark to bright
CH4
W Dimmer
0-255
White dimming from dark to bright
8 CH Mode
5.Dimension
Channel
Function
DMX Value
Description
CH1
Dimmer
0-255
Dimmer,0-100%
CH2
Red
0-255
Red dimming,0-100%
CH3
Green
0-255
Green dimming,0-100%
CH4
Blue
0-255
Blue dimming,0-100%
CH5
White
0-255
White dimming,0-100%
CH6
Strobe
0-10
No function
11-255
Strobe from slow to fast
CH7
Auto Mode
0-9
No function
10-50
Static Colors (CH8
choose color)
51-100
Colors Jump
101-150
Colors Fade
151-200
Colors Pulse
201-220
Sound Mode 1
221-240
Sound Mode 2
241-255
Sound Mode 3
CH8
Auto
Speed
0-255
Auto speed, slow to fast

7
6.Trouble Shooting
F ollo w ing a r e a few c o mm on p r oble m s th a t m a y occu r d uring ope r a tion . He r e a r e s o m e s ug g es tion s fo r
ea s y tr ou b leshooting :
A. The un it does no t work , no li ght a n d t he f a n d o es no t w o r k
1. Check th e c on nect ion of p owe r a nd m a in fu s e .
2. M eas ure th e m a ins volt a ge on th e m a i n co nn e ct o r .
3. Check th e pow er on LED .
B. N o t responding t o D MX c on t ro ll er
1. D M X LED s h ou ld b e on. If no t, che ck D M X co n nectors, ca b l es to s ee if link p r ope r ly .
2. If th e D M X LE D i s on a nd no r espons e t o th e c h a nn el, che ck th e a dd r ess s etti ng s a nd D M X p ol a r ity .
3. If y ou h a ve i nter m ittent D M X s ig n a l p r oble m s , che ck th e p ins on c onn ecto r s or on
PCB of th e u nit or the p r ev iou s on e.
4. Tr y to us e a no th er D M X co ntroller .
5. Check if th e D M X ca b le s r un ne a r or run a lon g s id e t o h ig h volta ge c a b les th a t m a y c a us e d a m a ge or
in terfer ence to D M X inter face circui t.
C . One of the cha nn el s is no t w o r k ing w el l
1. Th e s tep p er moto r m ig h t b e dam a g ed or the c a b le c on nect ed to th e PCB is b r oken.
2. Th e m oto r ’ s d r ive IC on th e PCB m ig h t b e o ut of co ndition
7.Fixture Cleaning
The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp,
smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s optics.
Clean with soft cloth using normal glass cleaning fluid.
Always dry the parts carefully.
Clean the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.