Uplus Lighting 200 LED RETRO User manual

User manual
200 LED RETRO
Please read the instructions carefully before use

2
TABLE OF CONTENTS
1. Safety Instructions……………………………………………………………………………3-4
Technical Specifications…………………………………………………………………………4
Control Menu ……………………………………………………………………………………5
DMX Channels ……………………………………………………………………………………5-6
Trouble Shooting…………………………………………………………………………………6
Fixture Cleaning………………………………………………………… ………………………6
STATEMENT
The product has well capability and intact packing when leave factory. All of the user should
comply with warning item and manual, any misuse cause of the damages are not included in our
guarantee, and also can not be responsible for any malfunction & problem owing to ignore the
manual.

3
1.Safety Instructions
Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that
they also receive this instruction booklet.
•Unpack and check carefully there is no transportation damage before using the unit.
•Before operating, ensure that the voltage and frequency of power supply match the power
requirements of the unit.
•It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
•The unit is for indoor use only. Use only in a dry location.
•The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent
surfaces. Be sure that no ventilation slots are blocked.
•Disconnect main power before replacement or servicing.
•Make sure there are no flammable materials close to the unit while operating as it is fire hazard.
•Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but always
by taking its base.
•Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is higher
than this Unit surface temperature may reach up to 85℃. DO NOT touch the housing bare-hand
during its operation. Turn off the power and allow about 15 minutes for the unit to cool down before
replacing or serving.
•the event of serious operating problem, stop using the unit immediately.Never try to repair the unit
by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please
contact the nearest authorized technical assistance center. Always use the same type spare parts.
•DO NOT touch any wire during operation as high voltage might be causing electric shock.
Warning:
•To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture.
•The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.
Caution:
•There are no user serviceable parts inside the unit. DO NOT open the housing or attempt any
repairs yourself. In the unlikely event your unit may require service, please contact your nearest
dealer.
Installation:
•The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly

4
fixed to avoid vibration and slipping while operating. And make sure that the structure to which you
are attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight. Also
always use a safety cable that can hold 12 times of the weight of the unit when installing the fixture.
•The equipment must be fixed by professionals. And it must be fixed at a place where is out of the
touch of people.
2.Technical Specifications
Light Sources: 200W LED White+RGB LED
Max Power Consumption: 260W
Power Input: 100-240V, 50/60Hz
Color Tempreture: 2400K or 3200K optional
LED Lifespan: 50000 hours
Operating mode: DMX512,Auto, Sound active, Master/slave,RDM
Channel mode: 12/37 DMX512 Channel
Beam range:102°
Display: Digital display
IP level: IP30
Dimension: 580*370*500mm
N.W：14kgs
All aluminum alloy structure, light and stylish design, elegant and generous. The biggest feature is
the close combination of traditional light source and LED,
LED200W lamp beads are used, and full-color LED are used as the background light to achieve
extraordinary visual effects. The lamp head is equipped with a protective decorative mesh.
No glare or glare. It can be quickly hung or used with a tripod, and the light is soft. It is suitable for
TV stations, studios,
It is used in large-scale entertainment occasions such as mobile performances. It can also be used
in commercial lighting or decorative lamps,
In addition to DMX control, there are powerful RDM control and wireless DMX control technology

5
3.Control Menu
Menu Operation
On the base of the control panel offers a number of features, such as setting DMX fixture address,
switch the lamp, run the test program, the mode selection.
No
Show
Value
Instruction
1
d001
001- 512
DMX512 -37Channels
2
A001
001- 512
DMX512 -12Channels
3
r255
000 - 255
Red dimmer-from dark to light
4
G255
000 - 255
Green dimmer-from dark to light
5
b255
000 - 255
Blue dimmer-from dark to light
6
u255
000 - 255
White dimmer-from dark to light
7
CL01
01 - 08
8 color output
8
FH01
01 -16
16 effects, from slow to fast.
4.DMX Channels
Model – CH12
Channel
DMX Value
Dispaly
Function
CH 1
0－255
Dimming
From dark to bright
CH 2
0－255
White
From dark to bright
CH 3
0－255
Strobe
From slow to fast
CH 4
0－255
Red
From dark to bright
CH 5
0－255
Green
From dark to bright
CH 6
0－255
Blue
From dark to bright
CH 7
0－255
Total Strobe
From slow to fast
CH 8
0－255
Feature selection
0—15;DMX Dimmer;15-255 effect
CH 9
0－255
Feature Speed
From slow to fast
CH 10
0－255
Red 1
Red 1 background , from dark to bright
CH 11
0－255
Green 1
Green 1 background , from dark to bright
CH 12
0－255
Blue 1
Blue 1 background , from dark to bright
Model – CH37
Channel
DMX Value
Dispaly
Function
CH 1
0－255
White
From dark to bright
CH 2
0－255
Red 1
From dark to bright
CH 3
0－255
Green 1
From dark to bright
CH 4
0－255
Blue 1
From dark to bright
……
……
……
……
……
……
……
……
……
……
……
……

6
CH 35
0－255
Red 12
From dark to bright
CH 36
0－255
Green 12
From dark to bright
CH 37
0－255
Blue 12
From dark to bright
5.Trouble Shooting
F ollo w ing a r e a few c o mm on p r oble m s th a t m a y occu r d uring ope r a tion . He r e a r e s o m e s ug g es tion s fo r
ea s y tr ou b leshooting :
A. The un it does no t work , no li ght a n d t he f a n d o es no t w o r k
1. Check th e c on nect ion of p owe r a nd m a in fu s e .
2. M eas ure th e m a ins volt a ge on th e m a i n co nn e ct o r .
3. Check th e pow er on LED .
B. N o t responding t o D MX c on t ro ll er
1. D M X LED s h ou ld b e on. If no t, che ck D M X co n nectors, ca b l es to s ee if link p r ope r ly .
2. If th e D M X LE D i s on a nd no r espons e t o th e c h a nn el, che ck th e a dd r ess s etti ng s a nd D M X p ol a r ity .
3. If y ou h a ve i nter m ittent D M X s ig n a l p r oble m s , che ck th e p ins on c onn ecto r s or on
PCB of th e u nit or the p r ev iou s on e.
4. Tr y to us e a no th er D M X co ntroller .
5. Check if th e D M X ca b le s r un ne a r or run a lon g s id e t o h ig h volta ge c a b les th a t m a y c a us e d a m a ge or
in terfer ence to D M X inter face circui t.
C . One of the cha nn el s is no t w o r k ing w el l
1. Th e s tep p er moto r m ig h t b e dam a g ed or the c a b le c on nect ed to th e PCB is b r oken.
2. Th e m oto r ’ s d r ive IC on th e PCB m ig h t b e o ut of co ndition
6.Fixture Cleaning
The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp,
smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s optics.
Clean with soft cloth using normal glass cleaning fluid.
Always dry the parts carefully.
Clean the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.