Uplus Lighting 200 LED BSW User manual

User manual
200 LED BSW
Please read the instructions carefully before use

2
TABLE OF CONTENTS
1. Safety Instructions……………………………………………………………………………3-4
Technical Specifications…………………………………………………………………………4
Control Menu ……………………………………………………………………………………5-7
DMX Channels ……………………………………………………………………………………7-9
Dimension …………………………………………………………………………………………10
LUX DATA …………………………………………………………………………………………10
Trouble Shooting…………………………………………………………………………………11
Fixture Cleaning………………………………………………………… ………………………11
STATEMENT
The product has well capability and intact packing when leave factory. All of the user should
comply with warning item and manual, any misuse cause of the damages are not included in our
guarantee, and also can not be responsible for any malfunction & problem owing to ignore the
manual.

3
1.Safety Instructions
Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that
they also receive this instruction booklet.
•Unpack and check carefully there is no transportation damage before using the unit.
•Before operating, ensure that the voltage and frequency of power supply match the power
requirements of the unit.
•It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
•The unit is for indoor use only. Use only in a dry location.
•The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent
surfaces. Be sure that no ventilation slots are blocked.
•Disconnect main power before replacement or servicing.
•Make sure there are no flammable materials close to the unit while operating as it is fire hazard.
•Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but always
by taking its base.
•Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is higher
than this Unit surface temperature may reach up to 85℃. DO NOT touch the housing bare-hand
during its operation. Turn off the power and allow about 15 minutes for the unit to cool down before
replacing or serving.
•the event of serious operating problem, stop using the unit immediately.Never try to repair the unit
by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please
contact the nearest authorized technical assistance center. Always use the same type spare parts.
•DO NOT touch any wire during operation as high voltage might be causing electric shock.
Warning:
•To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture.
•The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.
Caution:
•There are no user serviceable parts inside the unit. DO NOT open the housing or attempt any
repairs yourself. In the unlikely event your unit may require service, please contact your nearest
dealer.
Installation:
•The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly

4
fixed to avoid vibration and slipping while operating. And make sure that the structure to which you
are attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight. Also
always use a safety cable that can hold 12 times of the weight of the unit when installing the fixture.
•The equipment must be fixed by professionals. And it must be fixed at a place where is out of the
touch of people.
2.Technical Specifications
Input Voltage: 100-240V, 50/60Hz
Output Voltage: V1:36V(Master board+LED driver), V2:12V(cooling fan+Display)
Power consumption: 220W
Power supply: 300W
Light source: 200W Osram LED Chip (21-24V,8A)
Color temperature: 8000K
Diameter of optic lens: 97mm
Beam angle: 6-35°
Color wheel: 1 color wheel, 7fixed colors plus white
Static gobo: 8 gobos plus 1 white circle
Rotation Gobo: 7 Gobo plus 1 white circle
Prism: 3 prism,can be rotated in both directions
Frost filter: with smooth wash effect
DMX Channel: 20CH
Four dimming curves
Operate mode: DMX512, selfpropelled, master/slave, RDM
Fixture size: 338*530*225mm
Features:
1.0-100% 16Bit smooth dimming,Four dimming curves
2. Overheating self-energy protection can extending lamp life
3.Three phase Motor with SY Brand ( XY axis magnetic coding positioning is more accurate)
4. two angle lens 6°and 35°can change the gobo size
5. High quality LCD touch screen
6. Power in & Out connector,3 or 5pin XLR inout & output can optional
7. Folding clamp can optional
8. Housing material: PA6 Nylon( Solid,high temperature resistance up to 200°flame retardance)

5
3.Control Menu
1—Displays the current DMX address in large font
2—Logo display area
3—DMX signal frame rate (FPS)
4—Current channel mode, the displayed number indicates the current channel number
5—Show current temperature
6—Current Mode (Master, Slave)
7—Current running mode (DMX512, Auto, User)
8—Error message. If a red band "x" is displayed, the self-test found an error. (Press down to view
specific error message)
9 - temperature display or other content (depending on lamp configuration)
10 —SN term display
11. Display the address code of the next fixture
menu operation
Option
Description
DMX address
set the DMX address
Channel Mode
Set the channel mode, the number of the menu option indicates the number of channels
Reset operation
reset the motor
Motor power off: Select "On", all motors are powered off; select "Off", all motors are powered
on and reset. Using this menu, it is possible to plug and unplug the motor and power-on
reset without turning off the main switch.
XY Axis
Reset Pan and Tilt Motors
Run: Set the run
mode.
The description of each menu option is as follows (Note: "Automatic" mode options may
vary according to different product models):
DMX: controlled and run by DMX512 console.
Self-propelled (factory test): run the program set by the factory, this program is mainly used

6
for factory test.
User program: run user self-programming program. The editing scene can be set in the [Run
Settings] - [Self-Programming] menu.
Manual
Manually set the value of the channel
Run Settings
Run parameter settings.
Master-slave mode
set master-slave mode
XY axis general settings
X-axis reverse
Select "Yes" to reverse the rotation direction of the Pan motor, select "No", and follow the
rotation direction at the factory.
Y-axis reverse
select "Yes" to reverse the rotation direction of the Pan motor, select "No", and follow the
rotation direction at the factory.
X-axis settings
start range: 0-254 End Range: 0-255
Y axis setting
start range: 0-254 End Range: 0-255
Dimming curve
select the dimming curve
Self programming
Step count
When no signal: select the operation mode if no DMX512 signal is detected
When powering on: Only when powering on, if no DMX signal is detected, the above
operation mode will be executed,
Otherwise, the last DMX action will be held
Centered
Except for Pan and Tilt, all other channels are cleared to zero.
Self-propelled (factory test/pattern/color): Run the program set by the factory.
User program
run user self-programming program.
Runtime
The action to be performed at any time as long as the DMX signal is lost.
Hold
Hold the DMX value of the last frame
Shut off
close the shutter
Display settings
LCD screen settings
advanced settings
Fine-tuning
Factory debugging function, which requires password authentication to enter.
Display
Menu screen flip setting
Language
Set the system language
Ignore errors
Some error reports may not affect the final use effect, or for the general purpose of the
product, you can choose to close some meaningless error reports
Factory setting
Set the logo on and off
Trim Recovery
After replacing the display board, use this menu to restore the trim data saved by the motor
board to the display board.
information
DMX value
Display the current received DMX signal value
Channel
Select the channel to be observed
Value
Displays the DMX value of the selected channel

7
Error
Display error message (if any item in this menu is wrong, an exclamation mark will be
displayed in the upper right corner of the menu cover)
Storage
Indicates whether the storage is functioning normally. If the memory is abnormal, the menu
information cannot be recorded or read, and the lamp time record and self-programming
data may also be lost.
RAM Error
Chip memory allocation failed, if this error occurs, please contact the manufacturer.
Bus communication
If there is an error, the motors of various functions will not operate normally. If this error
occurs, please check whether the communication cables between the boards are in poor
contact.
X-axis reset
X-axis reset failed, check whether the optocoupler or motor is normal.
Y-axis reset
Y-axis reset fails, check whether the optocoupler or motor is normal.
Color reset
Color wheel reset failed
Gutu reset
Gutu disk reset failed
Focus error
focus positioning failed
Zoom in error
Zoom in positioning failed
Prism Error
Prism positioning failed
LED
Displays the usage time of the bulb
Usage time
Displays the total time the lamp has been on since the lamp time was reset to zero
Time Clear
The total time the bulb is on is cleared to 0.
Test mode
For product testing only, temporary use
Product Code
The internal code of the product is only for reference in product production and maintenance
4.DMX Channels
CH20
CH
DMX
describe
1
0-255
Pan
2
0-255
Pan fine
3
0-255
Tilt
4
0-255
Tilt fine
5
Pan/Tilt speed
0
NO
1-255
speed from fast to slow
6
0-255
Dimming
7
0-255
Dimming fine
8
Strobe
0-3
closure
4-103
Strobe from slow to fast
104-107
Open
108-207
Fast off and slow on, from fast to slow
208-212
Open
213-251
Random strobe, from slow to fast

8
252-255
Open
9
color wheel
0-7
Color 1 (white light)
8-15
color 1+color 2
16-23
color 2
24-31
color 2+color 3
32-39
color 3
40-47
color 3+color 4
48-55
color 4
56-63
color 4+color 5
64-71
color 5
72-79
color 5+color 6
80-87
color 6
88-95
color 6+color 7
96-103
color 7
104-111
color 7+color 8
112-119
color 8
120-127
color 8+color 1
128-190
Rainbow effect from fast to slow
191-192
rainbow effect stopped
193-255
Rainbow effect from slow to fast
10
GOBO
0-4
Open (white light hole)
5-12
GOBO 1
13-20
GOBO 2
21-28
GOBO 3
29-36
GOBO 4
37-44
GOBO 5
45-52
GOBO 6
53-60
GOBO 7
61-76
GOBO 8
77-89
GOBO 1shaking from slow to fast
90-102
GOBO 2 shaking from slow to fast
103-115
GOBO 3 shaking from slow to fast
116-128
GOBO 4 shaking from slow to fast
129-141
GOBO 5shaking from slow to fast
142-154
GOBO 6 shaking from slow to fast
155-167
GOBO 7 shaking from slow to fast
168-180
GOBO 8 shaking from slow to fast
181-201
Open
202-227
The shaking is scrolling forward, from fast to slow
228-229
stop scrolling
230-255
shaking scrolls in reverse, from slow to fast
11
Rotation GOBO
0-5
Open (white light hole)
6-15
GOBO1

9
16-25
GOBO2
26-35
GOBO3
36-45
GOBO4
46-55
GOBO5
56-65
GOBO6
66-75
GOBO7
76-92
GOBO 1shaking from slow to fast
93-109
GOBO 2 shaking from slow to fast
110-126
GOBO 3 shaking from slow to fast
127-143
GOBO 4 shaking from slow to fast
144-160
GOBO 5shaking from slow to fast
161-177
GOBO 6 shaking from slow to fast
178-199
GOBO 7 shaking from slow to fast
200-201
null
202-190
Forward gobo flow effect: from fast to slow
191-192
gobo stops spinning
193-255
Reverse gobo Flow Effect: Slow to Fast
12
GOBO rotation
0-127
Rotation gobo indexing
128-190
Forward gobo Rotation: Fast to Slow
191-192
stop
193-255
Reverse gobo Rotation: Slow to Fast
13
Prism
0-63
no prism
64-255
Prism Insert
14
Prism Rotation
0-127
Prism Positioning and Rotation
128-190
The prism rotates in reverse, from fast to slow
191-192
Prism stops spinning
193-255
The prism rotates forward, from slow to fast
15
frost
0-63
null
64-255
frost
16
0-255
ZOOM
17
0-255
Zoom fine
18
0-255
Focus
19
0-255
Focus fine
20
reset
0-199
null
200-209
Pan/Tilt reset
210-219
effect reset
220-229
reset all

10
5.Dimension
6.LUX DATA