Uplus Lighting MIX560 User manual

User manual
MIX560
Please read the instructions carefully before use

2
TABLE OF CONTENTS
1. Safety Instructions……………………………………………………………………………3-4
Technical Specifications…………………………………………………………………………4
Control Menu ……………………………………………………………………………………4-7
DMX Channels …………………………………………………………………………………7-10
Trouble Shooting…………………………………………………………………………………11
Fixture Cleaning………………………………………………………… ………………………11
STATEMENT
The product has well capability and intact packing when leave factory. All of the user should
comply with warning item and manual, any misuse cause of the damages are not included in our
guarantee, and also can not be responsible for any malfunction & problem owing to ignore the
manual.

3
1.Safety Instructions
Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that
they also receive this instruction booklet.
•Unpack and check carefully there is no transportation damage before using the unit.
•Before operating, ensure that the voltage and frequency of power supply match the power
requirements of the unit.
•It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
•The unit is for indoor use only. Use only in a dry location.
•The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent
surfaces. Be sure that no ventilation slots are blocked.
•Disconnect main power before replacement or servicing.
•Make sure there are no flammable materials close to the unit while operating as it is fire hazard.
•Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but always
by taking its base.
•Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is higher
than this Unit surface temperature may reach up to 85℃. DO NOT touch the housing bare-hand
during its operation. Turn off the power and allow about 15 minutes for the unit to cool down before
replacing or serving.
•the event of serious operating problem, stop using the unit immediately.Never try to repair the unit
by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please
contact the nearest authorized technical assistance center. Always use the same type spare parts.
•DO NOT touch any wire during operation as high voltage might be causing electric shock.
Warning:
•To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture.
•The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.
Caution:
•There are no user serviceable parts inside the unit. DO NOT open the housing or attempt any
repairs yourself. In the unlikely event your unit may require service, please contact your nearest
dealer.
Installation:
•The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly

4
fixed to avoid vibration and slipping while operating. And make sure that the structure to which you
are attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight. Also
always use a safety cable that can hold 12 times of the weight of the unit when installing the fixture.
•The equipment must be fixed by professionals. And it must be fixed at a place where is out of the
touch of people.
2.Technical Specifications
Voltage：AC100~240V 50/60HZ
Power consumption:500W
Led source: 5*60W RGBW LED
Strobe face: 96 pcs 7070 led with 12 sections + 72 pcs 5050 led with 6 sections
Pan & Tilt 360°no limited rotating
Zoom angle: 2.5-45°
Channel:33/53/69/105 CH
Dimming:32bit 0~100% linear dimming
Control mode: DMX512/ Music mode/ RDM
Working temperature:-30℃~50℃
Strobe frequency:1~30HZ
IP rating:IP20
Carton size:60*42*28cm
Gross weight:15kg
3.Control Menu
Menu Operation
Menu key:enter/return to the main menu
Up key: menu function up selection/Parameter increment
Down key：menu function down selection/parameter decrement

5
Enter key：Select the menu function, and confirm and save when the menu function parameters are modified.
Main Menu
Submenu
Menu Function Description
1. System
settings
2. Operating
mode
3. Manual
control
1. DMX
Address
Modify the DMX address code up or down (the address code can be selected
from 001-512), and press OK to save it. The default is 001.
2. Encoder
Modify the encoder on/off upward or downward, and save the confirmation key,
which is on by default.
3. X Reverse
Modify X up or down to turn it on/off. Press OK to save it. It is off by default.
4. Y Reverse
Modify Y upward or downward to turn it on/off. Press OK to save. It is closed by
default.
1. System
settings
2. Operating
mode
1. Operating
mode
Select up or down the operation mode DMX/voice control/auto, confirm to save,
default DMX.
2. Channel
selection
Select channels CH33, CH53, CH69, CH105 up or down, and press OK to save.
The default is CH33.
3.Manual
control
1. X axis
Modify the operating parameter value of X motor up or down (adjustable range
000-255), and press OK to save it. The default value is 000.
2. X Rotation
Modify the X rotation parameter value up or down (adjustable range 000-255),
and press OK to save. The default value is 000.
3. X axis fine
adjustment
Modify the operating parameter value of the X fine tuning motor up or down
(adjustable range 000-255), and save the confirmation key. The default value is
128.
4. Y axis
Modify the Y axis parameter value up or down (adjustable range 000-255), and
press OK to save. The default value is 128.
5. Y Rotation
Modify Y rotation parameter value up or down (adjustable range 000-255), and
press OK to save. The default value is 000.
6. Y-axis fine
adjustment
Modify Y fine-tuning parameter value up or down (adjustable range 000-255), and
press OK to save. The default value is 000.
7. XY speed
Modify the XY speed parameter value up or down (adjustable range 000-255),
and press OK to save. The default value is 000.
8. Focusing
Modify the focusing value up or down (adjustable range 000-255), and press the
OK key to save. The default is 000.
9. General
dimming
Modify the total dimming value up or down (adjustable range 000-255), and press
OK to save. The default value is 255.
10. A Dimming
Modify the dimming value up or down (adjustable range 000-255), and press OK
to save. The default value is 255.
11. A Strobe
Modify the stroboscopic value up or down (adjustable range 000-255), and press
OK to save. The default value is 000.
12. A Red
Modify the brightness of the red lamp bead up or down (adjustable range
000-255), and press OK to save. The default value is 255.
13. A Green
Modify the brightness of the green lamp bead up or down (adjustable range
000-255), and press OK to save. The default value is 255.
14. A Blue
Modify the brightness of the blue lamp bead up or down (adjustable range
000-255), and press OK to save. The default value is 255.
15. A White
Modify the brightness of white lamp beads up or down (adjustable range
000-255), and press OK to save. The default value is 255.
16. Mode A
Modify the mode parameter value up or down (adjustable range 000-255), and
press OK to save. The default value is 000.
17. A Speed
Modify the speed parameter value up or down (adjustable range 000-255), and
press OK to save. The default value is 000.
18. A
Background
color
Modify the background color parameter value up or down (adjustable range
000-255), and press OK to save. The default value is 000.
19. A
Background
tone light
Modify the background tone light parameter value up or down (adjustable range
000-255), and press OK to save. The default value is 000.
20. B Dimming
Modify the dimming value up or down (adjustable range 000-255), and press OK
to save. The default value is 255.
21. B
stroboscopic
Modify the stroboscopic value up or down (adjustable range 000-255), and press
OK to save. The default value is 000.

6
22. Mode B
Modify the mode parameter value up or down (adjustable range 000-255), and
press OK to save. The default value is 000.
23. Speed B
Modify the speed parameter value up or down (adjustable range 000-255), and
press OK to save. The default value is 000.
24. C dimming
Modify the dimming value up or down (adjustable range 000-255), and press OK
to save. The default value is 255.
25. C
stroboscopic
Modify the stroboscopic value up or down (adjustable range 000-255), and press
OK to save. The default value is 000.
26. C red
Modify the brightness of the red lamp bead up or down (adjustable range
000-255), and press OK to save. The default value is 255.
27. C green
Modify the brightness of the green lamp bead up or down (adjustable range
000-255), and press OK to save. The default value is 255.
28. C Blue
Modify the brightness of the blue lamp bead up or down (adjustable range
000-255), and press OK to save. The default value is 255.
29. Mode C
Modify the mode parameter value up or down (adjustable range 000-255), and
press OK to save. The default value is 000.
30. C speed
Modify the speed parameter value up or down (adjustable range 000-255), and
press OK to save. The default value is 000.
31. C
background
color
Modify the background color parameter value up or down (adjustable range
000-255), and press OK to save. The default value is 000.
32. C
background
tone light
Modify the background tone light parameter value up or down (adjustable range
000-255), and press OK to save. The default value is 000.
33、reset
When the parameter value is 150-255, the whole machine is reset. The console
parameter value must be pulled below 10 and then pushed to 150-255 to be
useful. When the parameter value is 000-149, it is useless and cannot be reset.
4.Display
Settings
1. Language
selection
Select Chinese/EN (English) up or down, and click OK to save. The default is
Chinese.
2. Invert
Settings
Select up or down to close/open the inverted display setting, and press OK to
save it. It is closed by default.
3. Screen saver
Select Close/Open the screen saver up or down, and press the Enter key to save
it. It is enabled by default.
4. Software
version
06XA program ID, which cannot be modified.
5.Factory
Settings
Please enter
password for
display!
Change it up or
down to 138,
and then press
the OK key to
enter the
factory setting。
1. X axis
calibration
Modify the parameters up or down (range 000-255), and press OK
to save. The default value is 128.
2. Y-axis
calibration
Modify the parameters up or down (range 000-255), and press OK
to save. The default value is 128.
2. X-axis
non-polar
Modify X stepless parameter up or down (range 000-255), and
press OK to save. The default value is 128.
2. Y-axis
non-polar
Modify Y stepless parameter up or down (range 000-255), and
press OK to save. The default value is 128.
3. Focus
calibration
Modify the parameters up or down (range 000-255), and press OK
to save. The default value is 128.
2. Focus
stroke
Modify the parameters up or down (range 000-255), and press OK
to save. The default value is 128.
5. Red
Modify the red lamp bead current (032-255) upward or downward,
and press OK to save. The default is 252.
6. Green
Modify the green lamp bead current (032-255) upward or
downward, and press OK to save. The default is 252.
7. Blue
Modify the blue lamp bead current (032-255) upward or downward,
and press OK to save. The default is 252.
8. White
Modify the white lamp bead current (032-255) upward or
downward, and press OK to save. The default is 252.
2. White 3W
Modify the white 3W lamp bead current (032-255) upward or
downward, and press OK to save. The default is 252.
9. X-axis
speed
Modify the X speed parameter up or down (range 000-255), and
press OK to save. The default is 116.
2. Y-axis
Modify Y speed parameter up or down (range 000-255), and press

7
speed
OK to save. The default is 128.
2、Logo
Select 000/001 up or down, and press OK to save. The default is
000.
2.
Temperature
Modify the temperature parameters up or down (range 40-70), and
press OK to save. The default is 060.
2.
Temperature
- Fan
Select the off/on temperature fan control upward or downward, and
press the OK key to save it. It is off by default.
2、LED
LED selection default LEDA
10. Current
Select 000/007 up or down, and press OK to save. The default is
000.
11、Logo
Select 000/001 up or down, and press OK to save. The default is
000.
12.
Temperature
Modify the temperature parameters up or down (range 40-70), and
press OK to save. The default is 065.
13.
Temperature
- Fan
Select the off/on temperature fan control upward or downward, and
the confirmation key is saved. The default is on.
4.DMX Channels
33 CH Mode
Channel
DMX value
function
1
000-255
X axis
2
000-255
X-axis non-polar
3
000-255
X Trim
4
000-255
Y axis
5
000-255
Y-axis non-polar
6
000-255
Y Trim
7
000-255
XY speed
8
000-255
focusing
9
000-255
Total dimming (AB side)
10
000-255
RGBW dimming (A-side)
11
000-255
RGBW strobe (A-side)
12
000-255
Red (Side A)
13
000-255
Green (Side A)
14
000-255
Blue (Side A)
15
000-255
White (Side A)
16
000-255
RGBW mode (A-side)
17
000-255
RGBW speed (A-side)
18
000-255
Background color (side A)
19
000-255
Background tone light (side A)
20
000-255
White 1 (Side B)
21
000-255
White 1 strobe (B side)
22
000-255
White 1 mode (B side)
23
000-255
White 1 speed (B side)
24
000-255
Red 1 green 1 blue 1 dimming (auxiliary light) (side B)
25
000-255
Red 1 green 1 blue 1 strobe (secondary light) (side B)
26
000-255
Red 1 (auxiliary light) (side B)
27
000-255
Green 1 (secondary light) (side B)
28
000-255
Blue 1 (secondary light) (side B)
29
000-255
Red 1 green 1 blue 1 mode (secondary light) (side B)
30
000-255
Red 1 green 1 blue 1 speed (secondary light) (side B)
31
000-255
Background color (secondary light) (side B)
32
000-255
Background tone light (auxiliary light) (side B)
33
000-255
Reset：When the parameter value is 150-255, the whole machine will be
reset. The console parameter value must be pulled below 10 and then
pushed to 150-255 to be useful. When the parameter value is 000-149, it is
useless and cannot be reset.

8
53 CH Mode
Channel
DMX value
function
1
000-255
X axis
2
000-255
X-axis non-polar
3
000-255
X Trim
4
000-255
Y axis
5
000-255
Y-axis non-polar
6
000-255
Y-axis fine adjustment
7
000-255
XY speed
8
000-255
focusing
9
000-255
Total dimming (AB side)
10
000-255
RGBW dimming (A-side)
11
000-255
RGBW strobe (A-side)
12
000-255
Red (Side A)
13
000-255
Green (Side A)
14
000-255
Blue (Side A)
15
000-255
White (Side A)
16
000-255
RGBW mode (A-side)
17
000-255
RGBW speed (A-side)
18
000-255
RGB background color (A side)
19
000-255
RGB background tone light (A-side)
20
000-255
White dimming (side B)
21
000-255
White strobe (side B)
22
000-255
White mode (side B)
23
000-255
White speed (side B)
24
000-255
RGB dimming
25
000-255
RGB strobe
26
000-255
red
27
000-255
green
28
000-255
blue
29
000-255
RGB mode
30
000-255
RGB speed
31
000-255
RGB background color
32
000-255
RGB background tone light
33
000-255
Reset：When the parameter value is 150-255, the whole machine will be
reset. The console parameter value must be pulled below 10 and then
pushed to 150-255 to be useful. When the parameter value is 000-149, it is
useless and cannot be reset.
34
000-255
Red 1 (Side A)
35
000-255
Green 1 (Side A)
36
000-255
Blue 1 (Side A)
37
000-255
White 1 (Side A)
…
… …
… …
50
000-255
Red 5 (Side A)
51
000-255
Green 5 (Side A)
52
000-255
Blue 5 (Side A)
53
000-255
White 5 (Side A)
69 CH Mode
Channel
DMX value
function
1
000-255
X axis
2
000-255
X-axis non-polar
3
000-255
X Trim
4
000-255
Y axis

9
5
000-255
Y-axis non-polar
6
000-255
Y-axis fine adjustment
7
000-255
XY speed
8
000-255
focusing
9
000-255
Total dimming (AB side)
10
000-255
RGBW dimming (A-side)
11
000-255
RGBW strobe (A-side)
12
000-255
Red (Side A)
13
000-255
Green (Side A)
14
000-255
Blue (Side A)
15
000-255
White (Side A)
16
000-255
RGBW mode (A-side)
17
000-255
RGBW speed (A-side)
18
000-255
RGB background color (A side)
19
000-255
RGB background tone light (A-side)
20
000-255
White dimming (side B)
21
000-255
White strobe (side B)
22
000-255
White mode (side B)
23
000-255
White speed (side B)
24
000-255
RGB dimming
25
000-255
RGB strobe
26
000-255
red
27
000-255
green
28
000-255
blue
29
000-255
RGB mode
30
000-255
RGB speed
31
000-255
RGB background color
32
000-255
RGB background tone light
33
000-255
Reset：When the parameter value is 150-255, the whole machine will be
reset. The console parameter value must be pulled below 10 and then
pushed to 150-255 to be useful. When the parameter value is 000-149, it is
useless and cannot be reset.
34
000-255
Red 1 (Side A)
35
000-255
Green 1 (Side A)
36
000-255
Blue 1 (Side A)
37
000-255
White 1 (Side A)
…
… …
… …
50
000-255
Red 5 (Side A)
51
000-255
Green 5 (Side A)
52
000-255
Blue 5 (Side A)
53
000-255
White 5 (Side A)
54
000-255
1 White (Side B)
…
… …
… …
69
000-255
16 White (Side B)
105 CH Mode
Channel
DMX value
function
1
000-255
X axis
2
000-255
X-axis non-polar
3
000-255
X Trim
4
000-255
Y axis
5
000-255
Y-axis non-polar
6
000-255
Y-axis fine adjustment

10
7
000-255
XY speed
8
000-255
focusing
9
000-255
Total dimming (AB side)
10
000-255
RGBW dimming (A-side)
11
000-255
RGBW strobe (A-side)
12
000-255
Red (Side A)
13
000-255
Green (Side A)
14
000-255
Blue (Side A)
15
000-255
White (Side A)
16
000-255
RGBW mode (A-side)
17
000-255
RGBW speed (A-side)
18
000-255
RGB background color (A side)
19
000-255
RGB background tone light (A-side)
20
000-255
White dimming (side B)
21
000-255
White strobe (side B)
22
000-255
White mode (side B)
23
000-255
White speed (side B)
24
000-255
RGB dimming
25
000-255
RGB strobe
26
000-255
red
27
000-255
green
28
000-255
blue
29
000-255
RGB mode
30
000-255
RGB speed
31
000-255
RGB background color
32
000-255
RGB background tone light
33
000-255
Reset：When the parameter value is 150-255, the whole machine will be
reset. The console parameter value must be pulled below 10 and then
pushed to 150-255 to be useful. When the parameter value is 000-149, it
is useless and cannot be reset.
34
000-255
Red 1 (Side A)
35
000-255
Green 1 (Side A)
36
000-255
Blue 1 (Side A)
37
000-255
White 1 (Side A)
…
… …
… …
50
000-255
Red 5 (Side A)
51
000-255
Green 5 (Side A)
52
000-255
Blue 5 (Side A)
53
000-255
White 5 (Side A)
54
000-255
1 White (Side B)
…
… …
… …
69
000-255
16 White (Side B)
70
000-255
Red 1 (Side B)
71
000-255
Green 1 (Side B)
72
000-255
Blue 1 (Side B)
…
… …
… …
103
000-255
Red 12 (Side B)
104
000-255
Green 12 (Side B)
105
000-255
Blue 12 (Side B)

11
5.Trouble Shooting
F ollo w ing a r e a few c o mm on p r oble m s th a t m a y occu r d uring ope r a tion . He r e a r e s o m e s ug g es tion s fo r
ea s y tr ou b leshooting :
A. The un it does no t work , no li ght a n d t he f a n d o es no t w o r k
1. Check th e c on nect ion of p owe r a nd m a in fu s e .
2. M eas ure th e m a ins volt a ge on th e m a i n co nn e ct o r .
3. Check th e pow er on LED .
B. N o t responding t o D MX c on t ro ll er
1. D M X LED s h ou ld b e on. If no t, che ck D M X co n nectors, ca b l es to s ee if link p r ope r ly .
2. If th e D M X LE D i s on a nd no r espons e t o th e c h a nn el, che ck th e a dd r ess s etti ng s a nd D M X p ol a r ity .
3. If y ou h a ve i nter m ittent D M X s ig n a l p r oble m s , che ck th e p ins on c onn ecto r s or on
PCB of th e u nit or the p r ev iou s on e.
4. Tr y to us e a no th er D M X co ntroller .
5. Check if th e D M X ca b le s r un ne a r or run a lon g s id e t o h ig h volta ge c a b les th a t m a y c a us e d a m a ge or
in terfer ence to D M X inter face circui t.
C . One of the cha nn el s is no t w o r k ing w el l
1. Th e s tep p er moto r m ig h t b e dam a g ed or the c a b le c on nect ed to th e PCB is b r oken.
2. Th e m oto r ’ s d r ive IC on th e PCB m ig h t b e o ut of co ndition
6.Fixture Cleaning
The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp,
smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s optics.
Clean with soft cloth using normal glass cleaning fluid.
Always dry the parts carefully.
Clean the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.