Uplus Lighting 150COBPAR User manual

User manual
150 COB PAR
Please read the instructions carefully before use

2
TABLE OF CONTENTS
1. Safety Instructions……………………………………………………………………………3
Technical Specifications………………………………………………………………………4
Control Menu ……………………………………………………………………………………5
DMX Channels …………………………………………………………………………………6-10
Trouble Shooting…………………………………………………………………………………11
Fixture Cleaning………………………………………………………… ………………………11
STATEMENT
The product has well capability and intact packing when leave factory. All of the user should
comply with warning item and manual, any misuse cause of the damages are not included in our
guarantee, and also can not be responsible for any malfunction & problem owing to ignore the
manual.

3
1.Safety Instructions
Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that they also
receive this instruction booklet.
•Unpack and check carefully there is no transportation damage before using the unit.
•Before operating, ensure that the voltage and frequency of power supply match the power requirements of the
unit.
•It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
•The unit is for indoor use only. Use only in a dry location.
•The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent surfaces. Be sure
that no ventilation slots are blocked.
•Disconnect main power before replacement or servicing.
•Make sure there are no flammable materials close to the unit while operating as it is fire hazard.
•Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but always by taking its
base.
•Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is higher than this Unit
surface temperature may reach up to 85℃. DO NOT touch the housing bare-hand during its operation. Turn off
the power and allow about 15 minutes for the unit to cool down before replacing or serving.
•the event of serious operating problem, stop using the unit immediately.Never try to repair the unit by yourself.
Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized
technical assistance center. Always use the same type spare parts.
•DO NOT touch any wire during operation as high voltage might be causing electric shock.
Warning:
•To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture.
•The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.
Caution:
•There are no user serviceable parts inside the unit. DO NOT open the housing or attempt any repairs yourself. In
the unlikely event your unit may require service, please contact your nearest dealer.
Installation:
•The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly fixed to avoid
vibration and slipping while operating. And make sure that the structure to which you are attaching the unit is
secure and is able to support a weight of 10 times of the unit’s weight. Also always use a safety cable that can
hold 12 times of the weight of the unit when installing the fixture.
•The equipment must be fixed by professionals. And it must be fixed at a place where is out of the touch of
people.

4
2.Technical Specifications
Light Sources: 1*150W COB RGB3IN1 Circle: 120pcs*0.2W White LED
Power Consumption: 210W
Power Voltage: AC 100-240V, 50/60Hz
Beam angle:40°
Dimension: 21*21*24.5cm
Inner Pack Size:26*26*38cm
Outer Pack Size:82*55*41cm
Quantity: 6pcs
N.W/PCS:2.35KG
G.W/CTN:23.4KG
Control
DMX Channel: 7/11/35 Channel
Control Modes: DMX 512, Auto mode, Master/Slave, Sound active
Construction
Display: LED Display
Data In/Out socket: 3-pin XLR sockets
Protection Rating: IP20
Features
Good cooling system, over heat protection
Dimmer: 0~100% smooth dimming

5
3.Control Menu
A- Menu
To navigate thru menu use "up" and "down" button.
To enter and validate use "enter"
To get out menu use "mode"
After a few seconds the display turn off, press any button to restart it.
MENU
Display
Instruction
DMX
Address
A001
Set DMX Address from 001 to 51
ChNd
7CH
Set Channel mode and choose into 3 mode 7/11 /35 channels (see DMX
charts after)
MANUAL
MANu
Set manually value of each parameter
rOOO
To set Red color from 0 to 255
gOOO
To set Green color from 0 to 255
bOOO
To set Blue color from 0 to 255
UOOO
To set internal white LED ring (1 thru 8) value from 0 to 255
M000
To set middle white LED ring (9 thru 16) value from 0 to 255
Y000
To set external white LED ring (17 thru 24) value from 0 to 255
AUTO
Shou
Sh 01
Set automatic internal program for COB LED and choose 1,2 or OFF internal
program
Sp 01
Set speed of internal program for COB LED and choose speed from 1 to 99
SMoN
SM 01
Set automatic internal program for Ring LED and choose 1 to 25 or OFF
internal program
SP01
Set speed of internal program for Ring LED and choose speed from 1 to 99
SEnS
1
Choose sensitivity of microphone and choose from 1 to 99
Soud
Soul
Choose sound control for internal program
Mode 1 to change step at each "kick" with dimmer always at full
Mode 2 to change step at each "kick" with dimmer On only when there is sound
FAN
FAN
Stud
Choose FAN control, studio or auto
INFO
MP
29
Temperature information in °C
SSDD
ON
NO DMX behaviour, if ON turn blackout after one second, if OFF hold last DMX
value

6
4.DMX Channels
B・MASTER/SLAVE MODE
To use master slave mode, link product as a daisy chain with Master in first position. Then choose
an automatic mode for Master and put every slave in DMX mode Addrl then slave product will act
as the master.
WARNING : The Cob par light mode generate DMX. This could generate trouble, so please double
check your menu and put each fixture in DMX mode to avoid any problem.
C-DMX CHART
DMX channel´s functions and values (7 DMX channels):
MODE 7 CHANNELS
Channels
Values
Features
1
0
255
RGB Dimmer :0-100%
2
0
255
Red: 0-100%
3
0
255
Green :0-100%
4
0
255
Blue :0-100%
5
0
255
White LED ring Dimmer 1 thru 24
6
0
255
White LED Ring Macros See Macros after DMX Charts
7
0
255
Macros speed
DMX channel´s functions and values (11 DMX channels):
MODE 11 CHANNELS
CHANNELS
VALUES
FEATURES
1
0
255
Dimmer: 0-100%
2
0
255
Red: 0-100%
3
0
255
Green : 0 -100%
4
0
255
Blue :0-100%
5
0
10
171
251
9
170
250
255
RGB Strobe Open Single flash (from slow to fast)
Double flash (from slow to fast) Open
6
0
255
RGB Macros See Macros after DMX Charts
7
0
255
RGB Macros speed

7
8
0
255
White LED ring Dimmer 1 thru 24
9
0
10
171
251
9
170
250
255
White Ring Strobe Open Single flash (from slow to fast)
Double flash (from slow to fast) Open
10
0
255
White LED ring Macros See Macros after DMX Chart
11
0
255
White LED Macros speed
DMX channel´s functions and values (35 DMX channels):
MODE 35 CHANNELS
CHANNELS
VALUES
FEATURES
1
0
255
Dimmer:0-100%
2
0
255
Red: 0-100%
3
0
255
Green :0-100%
4
0
255
Blue :0-100%
5
0
10 171
9
170
RGB Strobe Open Single flash (from slow to fast) Double flash
(from slow to fast) Open
6
0
255
RGB Macros
See Macros after DMX Charts
7
0
255
RGB Macros speed
8
0
255
White LED ring Dimmer 1 thru 24
9
0
255
White LED 1
10
0
255
White LED 2
11
0
255
White LED 3
12
0
255
White LED 4
13
0
255
White LED 5
14
0
255
White LED 6
15
0
255
White LED 7
16
0
255
White LED 8
17
0
255
White LED 9
18
0
255
White LED 10
19
0
255
White LED 11
20
0
255
White LED 12
21
0
255
White LED 13
22
0
255
White LED 14
23
0
255
White LED 15
24
0
255
White LED 16
25
0
255
White LED 17

8
26
0
255
White LED 18
27
0
255
White LED 19
28
0
255
White LED 20
29
0
255
White LED 21
30
0
255
White LED 22
31
0
255
White LED 23
32
0
255
White LED 24
33
0
10
171
251
9
170
250
25
White LED Ring Strobe Open Single flash (from slow to fast)
Double flash (from slow to fast) Open
34
0
255
White LED ring Macros See Macros after DMX Charts
35
0
255
White LED macros speed
D- MACROS FUNCTIONS
RGB LED Ring Macros
0--4
Off Red Green Blue Yellow Purple Cyan White Color chase Color
5--14
Fade Color pulse Color pulse up Color pulse down Blank Sound
15--24
Mode 1 Sound Mode 2 Full On
25--34
35--44
45--54
55--64
65--74
75--97
98--120
121--143
144--166
167--189
190---230
231--238
239--246
247--255

9
White LED Ring Macros
0--9
off
11--14
White LED 1/9/17
15--19
White LED 2/10/18
20--24
White LED 3/11/19
25--29
White LED 4/12/20
30--34
White LED 5/13/21
35--39
White LED 6/14/22
40--44
White LED 7/15/23
45--49
White LED 8/16/24
50--54
White LED 1/9/17+ 5/13/21
55--59
White LED 2/10/18 + 6/14/22 White LED 3/11/19 + 7/15/23
60--64
White LED 4/12/20+ 8/16/24
65--69
White LED 1 thru 8
70--74
White LED 9 thru 16
75--79
White LED 17 thru 24
80--84
White LED 1 thru 24
85--89
White LED 1 thru 24 pulse
90--95
White LED 1 thru 24 pulse
96--100
White LED 1 thru 24 pulse up
101--105
White LED 1 thru 24 pulse down
106--110
White LED 1 thru 24 macro 1
111--115
White LED 1 thru 24 macro 2
116--120
White LED 1 thru 24 macro 3
121--125
White LED 1 thru 24 macro 4
126--130
White LED 1 thru 24 macro 5
131--135
White LED 1 thru 24 macro 6
136--140
White LED 1 thru 24 macro 7
141--145
White LED 1 thru 24 macro 8
146--150
White LED 1 thru 24 macro 9
151--155
White LED 1 thru 24 macro 10

10
156--160
White LED 1 thru 24 macro 11
161--165
White LED 1 thru 24 macro 12
166--170
White LED 1 thru 24 macro 13
171--175
White LED 1 thru 24 macro 14
176--180
White LED 1 thru 24 macro 15
181--185
White LED 1 thru 24 macro 16
186--190
White LED 1 thru 24 macro 17
191-195
White LED 1 thru 24 macro 18
196--200
White LED 1 thru 24 macro 19
201--205
White LED 1 thru 24 macro 20
206-210
White LED 1 thru 24 macro 21
211--215
White LED 1 thru 24 macro 22
216--220
White LED 1 thru 24 macro 23
221--225
White LED 1 thru 24 macro 24
226--230
White LED 1 thru 24 macro 25 Sound Mode 1 (chaser) Sound
231--235
Mode 2 (flash)
236--240
Full On
241--245
246--250
251--255

11
5.Trouble Shooting
F ollo w ing a r e a few c o mm on p r oble m s th a t m a y occu r d uring ope r a tion . He r e a r e s o m e s ug g es tion s fo r
ea s y tr ou b leshooting :
A. The un it does no t work , no li ght a n d t he f a n d o es no t w o r k
1. Check th e c on nect ion of p owe r a nd m a in fu s e .
2. M eas ure th e m a ins volt a ge on th e m a i n co nn e ct o r .
3. Check th e pow er on LED .
B. N o t responding t o D MX c on t ro ll er
1. D M X LED s h ou ld b e on. If no t, che ck D M X co n nectors, ca b l es to s ee if link p r ope r ly .
2. If th e D M X LE D i s on a nd no r espons e t o th e c h a nn el, che ck th e a dd r ess s etti ng s a nd D M X p ol a r ity .
3. If y ou h a ve i nter m ittent D M X s ig n a l p r oble m s , che ck th e p ins on c onn ecto r s or on
PCB of th e u nit or the p r ev iou s on e.
4. Tr y to us e a no th er D M X co ntroller .
5. Check if th e D M X ca b le s r un ne a r or run a lon g s id e t o h ig h volta ge c a b les th a t m a y c a us e d a m a ge or
in terfer ence to D M X inter face circui t.
C . One of the cha nn el s is no t w o r k ing w el l
1. Th e s tep p er moto r m ig h t b e dam a g ed or the c a b le c on nect ed to th e PCB is b r oken.
2. Th e m oto r ’ s d r ive IC on th e PCB m ig h t b e o ut of co ndition
6.Fixture Cleaning
The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp,
smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s optics.
Clean with soft cloth using normal glass cleaning fluid.
Always dry the parts carefully.
Clean the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.