Uplus Lighting IP-L360 User manual

User manual
IP-L360
Please read the instructions carefully before use

2
TABLE OF CONTENTS
1. Safety Instructions………………………………………………………………………………3
Technical Specifications…………………………………………………………………………4-5
Installation…………………………………………………………………………………………5-7
Control Menu ………………………………………………………………………………………7
DMX Channels ……………………………………………………………………………………8-9
Dimension…………………………………………………………………………………………10
Trouble Shooting…………………………………………………………………………………11
Fixture Cleaning………………………………………………………… ………………………11
STATEMENT
The product has well capability and intact packing when leave factory. All of the user should
comply with warning item and manual, any misuse cause of the damages are not included in our
guarantee, and also can not be responsible for any malfunction & problem owing to ignore the
manual.

3
1.Safety Instructions
Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that
they also receive this instruction booklet.
•Unpack and check carefully there is no transportation damage before using the unit.
•Before operating, ensure that the voltage and frequency of power supply match the power
requirements of the unit.
•It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
•The unit is for indoor use only. Use only in a dry location.
•The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent
surfaces. Be sure that no ventilation slots are blocked.
•Disconnect main power before replacement or servicing.
•Make sure there are no flammable materials close to the unit while operating as it is fire hazard.
•Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but always
by taking its base.
•Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is higher
than this Unit surface temperature may reach up to 85℃. DO NOT touch the housing bare-hand
during its operation. Turn off the power and allow about 15 minutes for the unit to cool down before
replacing or serving.
•the event of serious operating problem, stop using the unit immediately.Never try to repair the unit
by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please
contact the nearest authorized technical assistance center. Always use the same type spare parts.
•DO NOT touch any wire during operation as high voltage might be causing electric shock.
Warning:
•To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture.
•The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.
Caution:
•There are no user serviceable parts inside the unit. DO NOT open the housing or attempt any
repairs yourself. In the unlikely event your unit may require service, please contact your nearest
dealer.
Installation:
•The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly
fixed to avoid vibration and slipping while operating. And make sure that the structure to which you
are attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight. Also
always use a safety cable that can hold 12 times of the weight of the unit when installing the fixture.
•The equipment must be fixed by professionals. And it must be fixed at a place where is out of the
touch of people.

4
2.Technical Specifications
Light Source:
Power supply: 100-240V - 50/60Hz
Power consumption: 400W
LED power: 360W
LED source: Ultra-bright 90x3W 7000K, 180x0.5W RGB
Optic: High efficiency optic system
Sections: 20 individual sections control (5xRGBW)
Luminous flux: Strobe 45000lm, Static >15000lm
Field angle: 90°
Dimmer mode: 8&16 Bit
Dimmer curve: Linear, curve
DMX mode: 13/20CH
Control mode: DMX, Auto, Master-slave
Protocol: DMX, RDM
Effect: Multi-layer, dynamic patterns, color mixing
Structure
IP rating: IP65
Body: Die-cast aluminum
Free light CON: Yes
Stand CON: 2 Max.
Hang drop CON: 4 Max.
Rotation 360: Yes
Working Condition: -30°~ 70°C
Connection
Power: True1 in & out
DMX: 3pin DMX in & out
Power cable: CCC 2.5mm2, 8 power link Max
Power and DMX cable type: Customized
Box Info
- Quick lock omega brackets
- Safety cable
- Floor stand
- Power & DMX cables
Carton: 2 in 1,

5
fly Case: 4 in 1 or 8 in 1
Fixture: L1004 x W96 x H130（Bracket H178) mm
Carton size(2in1): 1330x290x200mm
NW: 10KG (Gross 2in1 23.5KG)
Optional Accessories
- PMMA froster
- PMMA cover
- Barndoor
- Infinite rotation engine
- Clamp
- Flight case
3. Installation
Your IP24X15 BAR can be installed in every kind of following positions.
Please see the explanations and rely to the instructions for a safe operation and secure handling.
Structural Connection
The IP24X15 BAR can be connected using the included quick-release pins. Place the devices next
to each other.
(Insert both Pins to connect the devices)

6
For the first uses this may be a little hard. Move the devices a little until the Bolts can be inserted
completely. For vertical installation do not exceed the amount of 4 pieces. (caution, provisional
specification) In case of hanging installation, each device needs to be saved individually! Using the
quick-release pins for horizontal installation is not recommended. Each device should individually
be installed with the given installation options below.
Horizontal Installation on the floor
You could place the IP24X15 BAR on the floor by 2 stands. Please make sure the surface is plane
and the reliability of the floor is sufficient.
Horizontal hanging with tilt bracket
You can attach the IP24X15 BAR to a Truss or Pipe. Notice that the
tilt bracket(106mm) should face down from the hanging structure. Use the centered holes in the Tilt
Bracket. You can use the additional fix Omega Brackets to hang the device horizontal.
Hanging Vertically “dropped”
Use the vertical Adapter set (including Omega Bracket, optional accessory) to “drop” the IP24X15
BAR from a rigging structure.Notice that we will release a
detailed rigging manual for the different options shortly.
Vertical Installation on the floor
Use the vertical Adapter (optional accessory) in combination with a base plate (optional accessory)
. Use the Small standing plate (optional accessory) if
you only wish to install one IP24X15 BAR. If you want to install more than one
device, screw the Small standing plate to a normal truss base plate. We have two kinds of standing
plate, fixed and infinite rotating, for your options.
Notice that we will release a detailed rigging manual for the different options
shortly.
Safety attachment
In any case of rigging the device attach the Safety rope to any of the dedicated eyelets integrated i
nto the sliding brackets.

7
(Length of Omega & Safety cable position)
4.Control Menu
Display:
MENU To select the programming functions
DOWN To go backward in the selected functions
UP To go forward in the selected functions
ENTER To confirm the selected functions (unlock screen)
Operations:
Press "MENU" to unlock screen, then press “Menu” to select 7 different functions, Press the "UP or
DOWN"keys to increase or decrease the value,Press "ENTER" to save and Exit.
No.
Display
Description
1
DMX_CH11
Addr=001
Address
001-512
DMX
1-512
Current ctrl mode
Current DMX address
2
Ctrl Mode
DMX_CH
13/20
2CH Mode 13/20
Auto1
000-255
Built-in effect Auto1
Auto2
000-255
Built-in effect Auto2
Auto3
000-255
Built-in effect Auto3
3
Adjust
Red
000-255
Red Manual Dimmer
Green
000-255
Green Manual Dimmer
Blue
000-255
Blue Manual Dimmer
White
000-255
White Manual Dimmer
CURVE
000-255
Dimmer speed,
Display board menu has 1-5 kinds of dimming speed can be
selected
TEMP
000-255
Current temp

8
5.DMX Channels
12 Channel Mode
Channel
Function
DMX Value
Description
CH1
RGB Dimmer
0
OFF
1-255
Dimmer
CH2
Red
0
OFF
1-255
Dimmer
CH3
Green
0
OFF
1-255
Dimmer
CH4
Blue
0
OFF
1-255
Dimmer
CH5
White
0
OFF
1-255
Dimmer
CH6
Strobe Mode
0-5
No Function
6-42
Strobe mode 1
43-85
Strobe mode 2
86-128
Strobe mode 3
129-171
Strobe mode 4
172-214
Strobe mode 5
215-255
Strobe mode 6
CH7
Master Strobe Macro
0-15
Close
16-57
Macro 1
58-99
Macro 2
100-141
Macro 3
142-183
Macro 4
184-225
Macro 5
226-255
Macro 6
CH8
Effects strobe
0-9
No Function
10-255
Strobe from slow to fast
CH9
Effect Macro
0-4
Close
5-9
Macro 1
10-14
Macro 2
15-19
Macro 3
……
……
250-254
Macro 50
255
Macro 51
CH10
Effect Color Macro Speed
0-255
Speed from slow to fast
CH11
RGB Dimmer speed
0-255
Backlight Dimming speed from fast to slow
CH12
Effect Color Macro
0-255
Effect Color Macro

9
20 Channel Mode
Channel
Function
DMX Value
Description
CH1
Red 1
0
OFF
1-255
Dimmer
CH2
Green 1
0
OFF
1-255
Dimmer
CH3
Blue 1
0
OFF
1-255
Dimmer
CH4
White 1
0
OFF
1-255
Dimmer
CH5
Red 2
0
OFF
1-255
Dimmer
CH6
Green 2
0
OFF
1-255
Dimmer
CH7
Blue 2
0
OFF
1-255
Dimmer
CH8
White 2
0
OFF
1-255
Dimmer
CH9
Red 3
0
OFF
1-255
Dimmer
CH10
Green 3
0
OFF
1-255
Dimmer
CH11
Blue 3
0
OFF
1-255
Dimmer
CH12
White 3
0
OFF
1-255
Dimmer
CH13
Red 4
0
OFF
1-255
Dimmer
CH14
Green 4
0
OFF
1-255
Dimmer
CH15
Blue 4
0
OFF
1-255
Dimmer
CH16
White 4
0
OFF
1-255
Dimmer
CH17
Red 5
0
OFF
1-255
Dimmer
CH18
Green 5
0
OFF
1-255
Dimmer
CH19
Blue 5
0
OFF
1-255
Dimmer
CH20
White 5
0
OFF
1-255
Dimmer

10
6.Dimension

11
7.Trouble Shooting
F ollo w ing a r e a few c o mm on p r oble m s th a t m a y occu r d uring ope r a tion . He r e a r e s o m e s ug g es tion s fo r
ea s y tr ou b leshooting :
A. The un it does no t work , no li ght a n d t he f a n d o es no t w o r k
1. Check th e c on nect ion of p owe r a nd m a in fu s e .
2. M eas ure th e m a ins volt a ge on th e m a i n co nn e ct o r .
3. Check th e pow er on LED .
B. N o t responding t o D MX c on t ro ll er
1. D M X LED s h ou ld b e on. If no t, che ck D M X co n nectors, ca b l es to s ee if link p r ope r ly .
2. If th e D M X LE D i s on a nd no r espons e t o th e c h a nn el, che ck th e a dd r ess s etti ng s a nd D M X p ol a r ity .
3. If y ou h a ve i nter m ittent D M X s ig n a l p r oble m s , che ck th e p ins on c onn ecto r s or on
PCB of th e u nit or the p r ev iou s on e.
4. Tr y to us e a no th er D M X co ntroller .
5. Check if th e D M X ca b le s r un ne a r or run a lon g s id e t o h ig h volta ge c a b les th a t m a y c a us e d a m a ge or
in terfer ence to D M X inter face circui t.
C . One of the cha nn el s is no t w o r k ing w el l
1. Th e s tep p er moto r m ig h t b e dam a g ed or the c a b le c on nect ed to th e PCB is b r oken.
2. Th e m oto r ’ s d r ive IC on th e PCB m ig h t b e o ut of co ndition
8.Fixture Cleaning
The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp,
smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s optics.
Clean with soft cloth using normal glass cleaning fluid.
Always dry the parts carefully.
Clean the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.