Uplus Lighting IP1000 Strobe User manual

User manual
IP1000 Strobe
Please read the instructions carefully before use

2
TABLE OF CONTENTS
1. Safety Instructions……………………………………………………………………………3-4
2.Technical Specifications………………………………………………………………………4-5
3.Control Menu ……………………………………………………………………………………5-6
4.DMX Channels …………………………………………………………………………………7-11
5.Dimension…………………………………………………………………………………………12
6.Trouble Shooting…………………………………………………………………………………12
7.Fixture Cleaning………………………………………………………… ………………………13
STATEMENT
The product has well capability and intact packing when leave factory. All of the user should
comply with warning item and manual, any misuse cause of the damages are not included in our
guarantee, and also can not be responsible for any malfunction & problem owing to ignore the
manual.

3
1.Safety Instructions
Please keep this User Guide for future consultation. If you sell the unit to another user, be sure
that they also receive this instruction booklet.
•Unpack and check carefully there is no transportation damage before using the unit.
•Before operating, ensure that the voltage and frequency of power supply match the power
requirements of the unit.
•It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
•The unit is for indoor use only. Use only in a dry location.
•The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent
surfaces. Be sure that no ventilation slots are blocked.
•Disconnect main power before replacement or servicing.
•Make sure there are no flammable materials close to the unit while operating as it is fire hazard.
•Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but always
by taking its base.
•Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is higher
than this Unit surface temperature may reach up to 85℃. DO NOT touch the housing bare-hand
during its operation. Turn off the power and allow about 15 minutes for the unit to cool down before
replacing or serving.
•the event of serious operating problem, stop using the unit immediately.Never try to repair the unit
by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please
contact the nearest authorized technical assistance center. Always use the same type spare parts.
•DO NOT touch any wire during operation as high voltage might be causing electric shock.
Warning:
•To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture.
•The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.
Caution:
•There are no user serviceable parts inside the unit. DO NOT open the housing or attempt any
repairs yourself. In the unlikely event your unit may require service, please contact your nearest
dealer.
Installation:
•The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is

4
firmly fixed to avoid vibration and slipping while operating. And make sure that the structure to
which you are attaching the unit is secure and is able to support a weight of 10 times of the unit’s
weight. Also always use a safety cable that can hold 12 times of the weight of the unit when
installing the fixture.
•The equipment must be fixed by professionals. And it must be fixed at a place where is out of the
touch of people.
2.Technical Specifications
Strobe Panel LEDs
LED Type: 5050 0.5W RGB 3in1 LEDs
LED Count: 480
LED Colors: RGB
LED Segments: 8 (2 x 4)
Strobe Tube LEDs
LED Type: 3535 5W 6500K LEDs
LED Count: 144
LED Colors: Cool-White
LED Segments: 4
Movement
Resolution: 8-16 Bit
Tilt (Degrees): 185°
Control
Control Modes: 7CH / 14CH / 42CH / 15CH / 43CH
Display: Illuminated graphic LCD
Protocol: USITT DMX-512, RDM
RDM: Bidirectional communication
Wireless DMX: 2.4 GHz W-DMX™ (optional)
Cooling: Temperature controlled, overheating protection
Effects
Dimmer: 0-100% electronic
Shutter: electronic, max. 20 Hz
Internal Effects: LED Macro Effects
Connectors
Signal connection: Seetronic IP65 XLR 5-Pin or 3-Pin In/Out
Power Input: Seetronic PowerCON TRUE1 In/Out
Operating Conditions
Mains voltage: 100-240V AC / 50-60Hz

5
Power: 1000W
Maximum ambient temperature: -30°C / 86°F, 50°C / 122°F
Operating Position: any
Mounting Options
Hanging: Omega-Bracket
Safety wire attachment: foldout eyelets
Shipping
Single fixture: cardboard (inner and outer cartons)
Tourpack: 4-way Flight Case
Housing Colors
Standard colors: black
Dimensions
Length: 482 mm / 18.9 in
Width: 178 mm / 9.0 in
Height (head horizontal): 243 mm / 9.5 in
Weight
N.W: 10 kg
G.W: 12.5 kg
3.Control Menu
Display:
MENU To select the programming functions (press to unlock screen)
DOWN To go backward in the selected functions
UP To go forward in the selected functions
ENTER To confirm the selected functions
Set DMX Address:
1. Press "MENU" to unlock screen, then select the “DMX Address” and press "ENTER".
2. Showing "Set DMX Address 001", Press the "UP or DOWN" key to increase or decrease the
DMX address value.
Press "ENTER" to save and Exit, Press "Cancel" does not save and Exit

6
Level 1
Level 2
Description
DMX Address
Address
001-512
Set DMX address
DMX
Channel
Mode
DMX_CH7
7 channels DMX mode
DMX_CH14
14 channels DMX mode
DMX_CH42
42 channels DMX mode
DMX_CH15
15 channels DMX mode
DMX_CH43
43 channels DMX mode
Dimmer
Mode
DIM1
Dimmer mode 1
DIM2
Dimmer mode 2
DIM3
Dimmer mode 3
DIM4
Dimmer mode 4
DIM5
Dimmer mode 5
Mode
Selection
DMX512
DMX mode
Auto1
Auto run mode 1
Auto2
Auto run mode 2
Auto3
Auto run mode 3
Y motor
Tilt movement
White
Beam dimmer
W stroboscopic
Beam strobe
Red
Back light red dimmer
Green
Back light green dimmer
Blue
Back light blue dimmer
RGB stroboscopic
Back light strobe
System
Setting
Language
语言/English
Bk_Light
OFF/ON
Dmx512
Clear/Keep
W-DMX
Link/Unlink ( W-DMX version only )
System
Info
RDM UID
RDM UID
Version
Software Version Number
DMX Channel
Currently used mode

7
4.DMX Channels
7 Channel mode
Channel
Name
DMX
Value
Description
1
Tilt
0-255
Tilt Movement
2
Beam Dimmer
0-255
Beam Intensity
3
Beam Strobe Mode
0-5
No Strobe
6-42
Strobe Mode 1
43-85
Strobe Mode 2
86-128
Strobe Mode 3
129-171
Strobe Mode 4
172-214
Strobe Mode 5
215-255
Strobe Mode 6
4
Plate Red
0-255
Plate Red Dimmer
5
Plate Green
0-255
Plate Green Dimmer
6
Plate Blue
0-255
Plate Blue Dimmer
7
Plate Strobe
0-9
No Strobe
10-255
Strobe from slow to fast

8
14 Channel mode
Channel
Name
DMX
Value
Description
1
Tilt
0-255
Tilt Movement
2
Tilt Fine
0-255
Tilt Fine Movement
3
Beam Dimmer
0-255
Beam Intensity
4
Beam Strobe Mode
0-5
No Strobe
6-42
Strobe Mode 1
43-85
Strobe Mode 2
86-128
Strobe Mode 3
129-171
Strobe Mode 4
172-214
Strobe Mode 5
215-255
Strobe Mode 6
5
Reserved
Reserved Channel
6
Beam Macro
0-15
Beam Off
16-57
Beam Macro 1
58-99
Beam Macro 2
100-141
Beam Macro 3
142-183
Beam Macro 4
184-225
Beam Macro 5
226-255
Beam Macro 6
7
Plate Red
0-255
Plate Red Dimmer
8
Plate Green
0-255
Plate Green Dimmer
9
Plate Blue
0-255
Plate Blue Dimmer
10
Plate Strobe
0-9
No Strobe
10-255
Strobe from slow to fast
11
Plate Macro
0-4
Plate Macro Off
5-9
Plate Macro 1
10-14
Plate Macro 2
15-19
Plate Macro 3
…
Plate Macro …
250-254
Plate Macro 50
255
Plate Macro 51
12
Plate Macro Color
0-255
Plate Macro Color
13
Plate Macro Speed
0-255
Speed From Slow To Fast
14
Reserved
0-255
Reserved Channel

9
15 Channel mode
Channel
Name
DMX
Value
Description
1
Tilt
0-255
Tilt Movement
2
Tilt Fine
0-255
Tilt Fine Movement
3
Beam Dimmer
0-255
Beam Intensity
4
Beam Strobe Mode
0-5
No Strobe
6-42
Strobe Mode 1
43-85
Strobe Mode 2
86-128
Strobe Mode 3
129-171
Strobe Mode 4
172-214
Strobe Mode 5
215-255
Strobe Mode 6
5
Reserved
Reserved Channel
6
Beam Macro
0-15
Beam Off
16-57
Beam Macro 1
58-99
Beam Macro 2
100-141
Beam Macro 3
142-183
Beam Macro 4
184-225
Beam Macro 5
226-255
Beam Macro 6
7
Plate Red
0-255
Plate Red Dimmer
8
Plate Green
0-255
Plate Green Dimmer
9
Plate Blue
0-255
Plate Blue Dimmer
10
Plate Strobe
0-9
No Strobe
10-255
Strobe from slow to fast
11
Plate Macro
0-4
Plate Macro Off
5-9
Plate Macro 1
10-14
Plate Macro 2
15-19
Plate Macro 3
…
Plate Macro …
250-254
Plate Macro 50
255
Plate Macro 51
12
Plate Macro Color
0-255
Plate Macro Color
13
Plate Macro Speed
0-255
Speed From Slow To Fast
14
Tilt Speed
0-255
Tilt Speed From Fast To Slow
15
Dimmer Speed
0-255
Dimmer Speed From Fast To Slow

10
42 Channel mode
Channel
Name
DMX
Value
Description
1
Tilt
0-255
Tilt Movement
2
Tilt Fine
0-255
Tilt Fine Movement
3
Beam Dimmer
0-255
Beam Intensity
4
Beam Strobe Mode
0-5
No Strobe
6-42
Strobe Mode 1
43-85
Strobe Mode 2
86-128
Strobe Mode 3
129-171
Strobe Mode 4
172-214
Strobe Mode 5
215-255
Strobe Mode 6
5
Reserved
0-255
Reserved Channel
6
Beam Macro
0-15
Beam Off
16-57
Beam Macro 1
58-99
Beam Macro 2
100-141
Beam Macro 3
142-183
Beam Macro 4
184-225
Beam Macro 5
226-255
Beam Macro 6
7
Plate Red
0-255
Plate Red Dimmer
8
Plate Green
0-255
Plate Green Dimmer
9
Plate Blue
0-255
Plate Blue Dimmer
10
Plate Strobe
0-255
Plate Strobe
11
Plate Macro
0-4
Plate Macro Off
5-9
Plate Macro 1
10-14
Plate Macro 2
15-19
Plate Macro 3
…
Plate Macro …
250-254
Plate Macro 50
255
Plate Macro 51
12
Plate Macro Color
0-255
Plate Macro Color
13
Plate Macro Speed
0-255
Speed From Slow To Fast
14
Tilt Speed
0-255
Tilt Speed From Fast To Slow
15
Beam Pixel 1
0-255
Tube Pixel 1
16
Beam Pixel 2
0-255
Tube Pixel 2
17
Beam Pixel 3
0-255
Tube Pixel 3
18
Beam Pixel 4
0-255
Tube Pixel 4
19
Plate Pixel 1 Red
0-255
Plate Pixel 1 Red Dimmer
20
Plate Pixel 1 Green
0-255
Plate Pixel 1 Green Dimmer
21
Plate Pixel 1 Blue
0-255
Plate Pixel 1 Blue Dimmer
…
…
…
…
40
Plate Pixel 8 Red
0-255
Plate Pixel 8 Red Dimmer
41
Plate Pixel 8 Green
0-255
Plate Pixel 8 Green Dimmer
42
Plate Pixel 8 Blue
0-255
Plate Pixel 8 Blue Dimmer