Uplus Lighting 460LED BSW User manual

User manual
460LED BSW
Please read the instructions carefully before use

2
TABLE OF CONTENTS
1. Safety Instructions………………………………………………………………………………3
2.Technical Specifications…………………………………………………………………………4
3.DMX Channels ……………………………………………………………………………………5-10
4.LUX Date ……………………………………………………………………………………………10
5.Dimension …………………………………………………………………………………………11
6.Trouble Shooting…………………………………………………………………………………12
7.Fixture Cleaning………………………………………………………… ………………………12
STATEMENT
The product has well capability and intact packing when leave factory. All of the user should
comply with warning item and manual, any misuse cause of the damages are not included in our
guarantee, and also can not be responsible for any malfunction & problem owing to ignore the
manual.

3
1.Safety Instructions
Please keep this User Guide for future consultation. If you sell the unit to another user, be sure
that they also receive this instruction booklet.
•Unpack and check carefully there is no transportation damage before using the unit.
•Before operating, ensure that the voltage and frequency of power supply match the power
requirements of the unit.
•It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
•The unit is for indoor use only. Use only in a dry location.
•The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent
surfaces. Be sure that no ventilation slots are blocked.
•Disconnect main power before replacement or servicing.
•Make sure there are no flammable materials close to the unit while operating as it is fire hazard.
•Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but always
by taking its base.
•Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is higher
than this Unit surface temperature may reach up to 85℃. DO NOT touch the housing bare-hand
during its operation. Turn off the power and allow about 15 minutes for the unit to cool down before
replacing or serving.
•the event of serious operating problem, stop using the unit immediately.Never try to repair the unit
by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please
contact the nearest authorized technical assistance center. Always use the same type spare parts.
•DO NOT touch any wire during operation as high voltage might be causing electric shock.
Warning:
•To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture.
•The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.
Caution:
•There are no user serviceable parts inside the unit. DO NOT open the housing or attempt any
repairs yourself. In the unlikely event your unit may require service, please contact your nearest
dealer.
Installation:
•The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is
firmly fixed to avoid vibration and slipping while operating. And make sure that the structure to
which you are attaching the unit is secure and is able to support a weight of 10 times of the unit’s
weight. Also always use a safety cable that can hold 12 times of the weight of the unit when
installing the fixture.
•The equipment must be fixed by professionals. And it must be fixed at a place where is out of the
touch of people.

4
2.Technical Specifications
460W LED BSW 3-in-1 moving head
Optics:
Source:460W white LED
Life:>30000H
Zoom angle:6°-42°
Input power:550W
AC100-240V 50-60HZ
Pan movement:540°/630° optional(16bit)
Tilt movement:270°(16bit)
Advanced motion system:auto repositioning,fast,quiet and smooth
Color: CMY+CTO color mixing system
1 color plate: 7 fixed color plates + white light
Gobo: 1 effect plate (fire plate)
1 rotating gobo wheel: 7 gobos+white
1 fixed pattern plate: 8 pattern pieces + white
Prism: 1 bidirectional 5-face prism
5-100% electronic Iris
Frost: Light frost, heavy frost
Animation wheel: special dynamic water effect
Dimming: 0-100% linear dimming
Features:
DMX Channels:25/36channels
Control: DMX 512 , Art-net Ethernet, RDM
Dimension: 840*460* 380 mm, NW:24 kg

5
3.DMX Channels
DMX channel´s functions and values (25/36DMX channels)
Mode
DMX Value
Function Illustration
CH 25
CH 36
1
1
Pan Movement 8bit:
0－255
Pan Movement
2
2
Pan Fine 16bit:
0－255
Fine control of Pan movement
3
3
Tilt Movement 8bit:
0－255
Tilt Movement
4
4
Tilt Fine 16bit
0－255
Fine control of Tilt movement
5
5
Speed Pan/Tilt movement:
0－255
Max to min speed
6
6
Shutter,strobe
0－10
Shutter closed
140－149
X Y reset
150－189
Effect reset
190－199
Blank
200－209
Light reset
210－255
Blank
7
7
Shutter
0-3
Closed
4-103
Slow - fast
104-107
Open
108-207
Fast strobe-slow strobe
208-212
Open
213-251
Random slow - fast
252-255
Open
8
8
Dimmer
0－255
Linear dimmer
9
9
Colour
0-9
white
10-19
Colour 1
20-29
Colour 2
30-39
Colour 3
40-49
Colour 4
50-59
Colour 5
60-69
Colour 6

6
70-79
Colour 7
80-89
Colour 8
90-99
Colour 9
100-109
Colour 10
110-119
Colour 11
120-129
Colour 12
130-139
Colour 13
140-149
Colour 14
150-159
Colour 15
160-204
Fast rotation - slow rotation
205-210
Stop
211-255
Slow rotation - fast rotation
10
*
Color Fine
0－255
Linear
11
10
Gobo 1
0-4
white
5-24
Gobo1
25-44
Gobo2
45-64
Gobo3
11－21
Shutter open
22－126
Strobe effect slow to fast
127－137
Shutter open
138－201
Pulse-effect in sequences
202－212
Shutter open
213－244
Random strobe effect slow to fast
245－255
Shutter open
7
7
Dimmer intensity
0－255
Intensity 0 to 100%
8
Dimmer intensity Fine:
0－255
Dimmer intensity Fine
8
9
Zoom:
0－255
Zoom adjustment from small to big
10
Zoom fine:
0－255
Zoom adjustment fine
9
11
Focus:
0－255
Continuous adjustment from near to far
12
Focus Fine:
0－255
Continuous adjustment fine
10
13
Auto Focus:
0－51
Auto Focus off
52－102
5m
103－153
7.5m

7
154－204
10m
205－255
15m
11
14
Auto Focus fine:
0－255
Continuous adjustment fine
12
15
Color Wheel:
0－15
Open
16－22
Open/Color 1
23－29
Color 1
30－36
Color 1 / Color 2
37－43
Color 2
44－50
Color 2 / Color 3
51－57
Color 3
58－64
Color 3/ Color 4
65－71
Color 4
72－78
Color 4/ Color 5
79－85
Color 5
86－92
Color 5/ Color 6
93－99
Color 6
100－106
Color 6/ Color 7
107－113
Color 7
114－120
Color 7/Open
121－127
Open
128－189
Forwards rainbow effect from fast to slow
190－193
No rotation
194－255
Backwards rainbow effect from slow to fast
16
Color Wheel Fine:
0－255
Color Wheel colour change to any position fine
13
17
Cyan Color:
0－255
Cyan(0-white,255-100% Cyan)
18
Cyan Colorf Fine:
0－255
Cyan Fine
14
19
Magenta Color Fine:
0－255
Magenta(0-white,255-100% Magenta)
20
Magenta Fine Fine:
0－255
Magenta Fine
15
21
Yellow Color:
0－255
Yellow(0-white,255-100% Yellow)
22
Yellow Color Fine:
0－255
Yellow Fine
16
23
CTO Color:
0－255
CTO(0-white,255-100% CTO)
24
CTO Color Fine:

8
0－255
CTO fine
17
25
Rotating gobos.cont,rotation 1:
0－7
Open
8－20
Rot.gobo 1
21－33
Rot.gobo 2
34－46
Rot.gobo 3
47－59
Rot.gobo 4
60－72
Rot.gobo 5
73－85
Rot.gobo 6
86－98
Rot.gobo 7
99－111
Gobo 1 shake slow to fast
112－124
Gobo 2 shake slow to fast
125－137
Gobo 3 shake slow to fast
138－150
Gobo 4 shake slow to fast
151－163
Gobo 5 shake slow to fast
164－176
Gobo 6 shake slow to fast
177－189
Gobo 7 shake slow to fast
190－221
Gobo wheel rotation forwards from fast to slow
222－223
No rotation
224-255
Gobo wheel rotation backwards from slow to fast
18
26
Rotating gobo index,rotating gobo rotation 1:
0－127
Gobo indexing
128－189
Forwards gobo rotation from fast to slow
190－193
No rotation
194－255
Backwards gobo rotation from slow to fast
27
Rotating gobo indexing Fine 1:
0－255
Fine indexing
19
28
Fixed Gobo2:
0－9
Open
10－19
Gobo 1
20－29
Gobo 2
30－39
Gobo 3
40－49
Gobo 4
41－59
Gobo 5
60－69
Gobo 6
70－79
Gobo 7
80－89
Gobo 8
90－99
Gobo 9
100－109
Gobo 1 shake slow to fast
110－119
Gobo 2 shake slow to fast
120－129
Gobo 3 shake slow to fast
130－139
Gobo 4 shake slow to fast

9
140－149
Gobo 5 shake slow to fast
150－159
Gobo 6 shake slow to fast
160－169
Gobo 7 shake slow to fast
170－179
Gobo 8 shake slow to fast
180－189
Gobo 9 shake slow to fast
190－221
Gobo wheel rotation forwards from fast to slow
222－223
No rotation
224－255
Gobo wheel rotation backwards from slow to fast
20
29
Animation wheel:
0－127
Animation indexing
128－189
Forwards rotation from fast to slow
190－193
No rotation
194－255
Backwards rotation from slow to fast
21
30
Iris:
0－255
Max.diameter to Min.diameter
31
Iris Fine:
0－255
Iris Fine
22
32
Prism:
0－127
Open
128－255
Prism
23
33
Rotating prism index,rotating prism rotation
0－127
Prism indexing
128－189
Forwards prism rotation from fast to slow
190－193
No rotation
194－255
Backwards prism rotation from slow to fast
34
Rotating prism indexing fine:
0－255
Fine indexing
24
35
Frost:
0－127
Open
128－255
Frost
25
36
Reset、LCD、Fans
0－9
unused
10－19
Display off
20－29
Display on
30－39
Display Invert off
40－49
Display invert on
50－59
Auto fan control mode
60－69
High fan control mode
70－79
Silent fan control mode
80－89
Square Law
90－99
Inv SQ Law
100－109
Linear

10
110－119
S Curve
120－129
unused
130－139
Unused
140－149
Unused
150－159
All motor reset
160－169
Scan motor reset
170－179
Colors motor reset
180－189
Gobo motor reset
190－199
Other motor reset
200－255
unused
4.LUX Date

11
5.Dimension

12
6.Trouble Shooting
F ollo w ing a r e a few c o mm on p r oble m s th a t m a y occu r d uring ope r a tion . He r e a r e s o m e s ug g es tion s fo r
ea s y tr ou b leshooting :
A. The un it does no t work , no li ght a n d t he f a n d o es no t w o r k
1. Check th e c on nect ion of p owe r a nd m a in fu s e .
2. M eas ure th e m a ins volt a ge on th e m a i n co nn e ct o r .
3. Check th e pow er on LED .
B. N o t responding t o D MX c on t ro ll er
1. D M X LED s h ou ld b e on. If no t, che ck D M X co n nectors, ca b l es to s ee if link p r ope r ly .
2. If th e D M X LE D i s on a nd no r espons e t o th e c h a nn el, che ck th e a dd r ess s etti ng s a nd D M X
p ol a r ity .
3. If y ou h a ve i nter m ittent D M X s ig n a l p r oble m s , che ck th e p ins on c onn ecto r s or on
PCB of th e u nit or the p r ev iou s on e.
4. Tr y to us e a no th er D M X co ntroller .
5. Check if th e D M X ca b le s r un ne a r or run a lon g s id e t o h ig h volta ge c a b les th a t m a y c a us e d a m a ge or
in terfer ence to D M X inter face circui t.
C . One of the cha nn el s is no t w o r k ing w el l
1. Th e s tep p er moto r m ig h t b e dam a g ed or the c a b le c on nect ed to th e PCB is b r oken.
2. Th e m oto r ’ s d r ive IC on th e PCB m ig h t b e o ut of co ndition
7.Fixture Cleaning
The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates:
damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s optics.
Clean with soft cloth using normal glass cleaning fluid.
Always dry the parts carefully.
Clean the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.