Uplus Lighting RETRO 360 User manual

User manual
RETRO 360
Please read the instructions carefully before use

2
TABLE OF CONTENTS
1. Safety Instructions………………………………………………………………………………3-4
Technical Specifications…………………………………………………………………………4
Control Menu ………………………………………………………………………………………5
DMX Channels ……………………………………………………………………………………6-7
Trouble Shooting……………………………………………………………………………………8
Fixture Cleaning………………………………………………………… …………………………8
STATEMENT
The product has well capability and intact packing when leave factory. All of the user should
comply with warning item and manual, any misuse cause of the damages are not included in our
guarantee, and also can not be responsible for any malfunction & problem owing to ignore the
manual.

3
1.Safety Instructions
Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that
they also receive this instruction booklet.
•Unpack and check carefully there is no transportation damage before using the unit.
•Before operating, ensure that the voltage and frequency of power supply match the power
requirements of the unit.
•It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
•The unit is for indoor use only. Use only in a dry location.
•The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent
surfaces. Be sure that no ventilation slots are blocked.
•Disconnect main power before replacement or servicing.
•Make sure there are no flammable materials close to the unit while operating as it is fire hazard.
•Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but always
by taking its base.
•Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is higher
than this Unit surface temperature may reach up to 85℃. DO NOT touch the housing bare-hand
during its operation. Turn off the power and allow about 15 minutes for the unit to cool down before
replacing or serving.
•the event of serious operating problem, stop using the unit immediately.Never try to repair the unit
by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please
contact the nearest authorized technical assistance center. Always use the same type spare parts.
•DO NOT touch any wire during operation as high voltage might be causing electric shock.
Warning:
•To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture.
•The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.
Caution:
•There are no user serviceable parts inside the unit. DO NOT open the housing or attempt any
repairs yourself. In the unlikely event your unit may require service, please contact your nearest
dealer.
Installation:
•The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly

4
fixed to avoid vibration and slipping while operating. And make sure that the structure to which you
are attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight. Also
always use a safety cable that can hold 12 times of the weight of the unit when installing the fixture.
•The equipment must be fixed by professionals. And it must be fixed at a place where is out of the
touch of people.
2.Technical Specifications
SPECIFICATIONS:
Light Source: 3*60W white & 72*0.3w RGB led
Input Voltage:AC90-260V 50/60Hz
Power Consumption: 250W
Control mode:DMX512,Auto-run , Master-Slave,RDM
Control Channel: 4/14/147 channels
PowerCon : powerCon in & out
DMX sockets:3-pin XLR sockets
Display: Digital Display
Strobe：1-30Hz multiple stroboscopic effect
Dimming：32bit 0-100% linear dimmer

5
3.Control Menu
Menu Operation
On the base of the control panel offers a number of features, such as setting DMX fixture address,
switch the lamp, run the test program, the mode selection.
No
Show
Instruction
1
A001 A512
001-512
2
Channel
4CH
14CH
147CH
3
N127
Fill light effect mode
4
S000 S255
Modify the auxiliary light effect running speed up or down
(S000~S255)
5
E007
Intermediate key light mode
6
S000 S255
Modify the running speed of the intermediate main light up or down
(S000~S255)
7
Sound
Sound
8
R255 R000
R dimmer
9
G255 G000
G dimmer
10
B255 B000
B dimmer
11
W255 W000
W dimmer
12
T000
Display temperature, such as T045 means the current lamp
temperature is 45℃

6
4.DMX Channels
4 DMX channels
CH 4
DMX Value
Function
Function Illustration
1
0-255
Red
R Dimmer dark to light
2
0-255
Green
G Dimmer dark to light
3
0-255
Blue
B Dimmer dark to light
4
0-255
White
W Dimmer dark to light
14 DMX channels
CH 14
DMX Value
Function
Function Illustration
1
0－255
Total Dimmer
Total Dimmer
2
0－9
Strobe
No function
10－255
Slow to fast
3
0-255
Red
R Dimmer dark to light
4
0-255
Green
G Dimmer dark to light
5
0-255
Blue
B Dimmer dark to light
6
0-255
RGB Effect
2 values and one effect
7
0-127
RGB Speed
positive
128-255
reverse
8
0-255
RGB background color
RGB background color
9
0-255
RGB background Dimmer
RGB background Dimmer
10
0-255
White Dimmer
White Dimmer dark to light
11
0-255
White Strobe
White Strobe slow to fast
12
0-255
White Liner Dimmer
White Liner Dimmer dark to light
13
0-255
White Effect
32 values for one effect
14
0-255
White speed
fast to slow
147 DMX channels
CH 147
DMX Value
Function
Function Illustration
1
0-255
Red1
Red1 Liner Dimmer
2
0-255
Green1
Green1 Liner Dimmer
3
0-255
Blue1
Blue1 Liner Dimmer
4
0-255
Red2
Red2 Liner Dimmer
5
0-255
Green2
Green2 Liner Dimmer
6
0-255
Blue2
Blue2 Liner Dimmer
7
0-255
Red3
Red3 Liner Dimmer
8
0-255
Green3
Green3 Liner Dimmer
9
0-255
Blue3
Blue3 Liner Dimmer
…
0-255
…
…

7
136
0-255
Red46
Red46 Liner Dimmer
137
0-255
Green46
Green46 Liner Dimmer
138
0-255
Blue46
Blue46 Liner Dimmer
139
0-255
Red47
Red47 Liner Dimmer
140
0-255
Green47
Green47 Liner Dimmer
141
0-255
Blue47
Blue47 Liner Dimmer
142
0-255
Red48
Red48 Liner Dimmer
143
0-255
Green48
Green48 Liner Dimmer
144
0-255
Blue48
Blue48 Liner Dimmer
145
0-255
White1
White1 Liner Dimmer
146
0-255
White2
White2 Liner Dimmer
147
0-255
White3
White3 Liner Dimmer
EFFECT Mode
NO
DMX Value
Function
0
0-7
No function
1
8-15
Effect 1
2
16-23
Effect 1
3
24-31
Effect 3
4
32-39
Effect 4
…
……
……
29
232-239
Effect 29
30
240-247
Effect 1-29 cycle
31
248-255
Sound

8
5.Trouble Shooting
F ollo w ing a r e a few c o mm on p r oble m s th a t m a y occu r d uring ope r a tion . He r e a r e s o m e s ug g es tion s fo r
ea s y tr ou b leshooting :
A. The un it does no t work , no li ght a n d t he f a n d o es no t w o r k
1. Check th e c on nect ion of p owe r a nd m a in fu s e .
2. M eas ure th e m a ins volt a ge on th e m a i n co nn e ct o r .
3. Check th e pow er on LED .
B. N o t responding t o D MX c on t ro ll er
1. D M X LED s h ou ld b e on. If no t, che ck D M X co n nectors, ca b l es to s ee if link p r ope r ly .
2. If th e D M X LE D i s on a nd no r espons e t o th e c h a nn el, che ck th e a dd r ess s etti ng s a nd D M X p ol a r ity .
3. If y ou h a ve i nter m ittent D M X s ig n a l p r oble m s , che ck th e p ins on c onn ecto r s or on
PCB of th e u nit or the p r ev iou s on e.
4. Tr y to us e a no th er D M X co ntroller .
5. Check if th e D M X ca b le s r un ne a r or run a lon g s id e t o h ig h volta ge c a b les th a t m a y c a us e d a m a ge or
in terfer ence to D M X inter face circui t.
C . One of the cha nn el s is no t w o r k ing w el l
1. Th e s tep p er moto r m ig h t b e dam a g ed or the c a b le c on nect ed to th e PCB is b r oken.
2. Th e m oto r ’ s d r ive IC on th e PCB m ig h t b e o ut of co ndition
6.Fixture Cleaning
The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp,
smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s optics.
Clean with soft cloth using normal glass cleaning fluid.
Always dry the parts carefully.
Clean the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.