Uplus Lighting IP MATRIX 5 User manual

User manual
IP MATRIX 5
Please read the instructions carefully before use

2
TABLE OF CONTENTS
1. Safety Instructions………………………………………………………………………………3-4
Technical Specifications……………………………………………………………………………4
Control Menu …………………………………………………………………………………………4
DMX Channels ………………………………………………………………………………………5-7
Trouble Shooting……………………………………………………………………………………8
Fixture Cleaning………………………………………………………… …………………………8
STATEMENT
The product has well capability and intact packing when leave factory. All of the user should
comply with warning item and manual, any misuse cause of the damages are not included in our
guarantee, and also can not be responsible for any malfunction & problem owing to ignore the
manual.

3
1.Safety Instructions
Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that
they also receive this instruction booklet.
•Unpack and check carefully there is no transportation damage before using the unit.
•Before operating, ensure that the voltage and frequency of power supply match the power
requirements of the unit.
•It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
•The unit is for indoor use only. Use only in a dry location.
•The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent
surfaces. Be sure that no ventilation slots are blocked.
•Disconnect main power before replacement or servicing.
•Make sure there are no flammable materials close to the unit while operating as it is fire hazard.
•Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but always
by taking its base.
•Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is higher
than this Unit surface temperature may reach up to 85℃. DO NOT touch the housing bare-hand
during its operation. Turn off the power and allow about 15 minutes for the unit to cool down before
replacing or serving.
•the event of serious operating problem, stop using the unit immediately.Never try to repair the unit
by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please
contact the nearest authorized technical assistance center. Always use the same type spare parts.
•DO NOT touch any wire during operation as high voltage might be causing electric shock.
Warning:
•To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture.
•The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.
Caution:
•There are no user serviceable parts inside the unit. DO NOT open the housing or attempt any
repairs yourself. In the unlikely event your unit may require service, please contact your nearest
dealer.
Installation:
•The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly

4
fixed to avoid vibration and slipping while operating. And make sure that the structure to which you
are attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight. Also
always use a safety cable that can hold 12 times of the weight of the unit when installing the fixture.
•The equipment must be fixed by professionals. And it must be fixed at a place where is out of the
touch of people.
2.Technical Specifications
Input Voltage:AC90-240V,50/60Hz
Power Consumption:100W
Light Source:5pcs 15W RGBW 4in1 LED
Each LED can be controlled individual
Lamp life:50000hrs
Beam Angle: 30 ゜
Display :Digital display
Control Mode:DDMX, auto, RDM
DMX Channel:6/7/21/30 DMX Channels
Dimmer:0-100% smooth linear adjustment
Strobe:High speed strobe effect with 1-25 flashes per second
IP Rate:IP65
Strobe: 0-30Hz
Each light can link to work
Dimension:580*160*120MM (L*W*H)
Net weight：5.4Kg

5
3.Control Menu
Display:
MENU
DMX display
Function
DMX addr
DMX address setting
001
chan Mod
DMX channel mode option:6/7/21/30
06CH
workMod
work mode: DMX,auto
DMX512
AutoSP
Auto mode speed setting
80
M/S mod
master/slave setting, set Master for master unit, set SLAVE for DMX and slave
unit
Slave
Dimm mod
Dimmer mode setting: normal mode, delay mode
normal
Runtime
total working time
0000
Versin
software version
V0.01
4.DMX Channels
DMX Channels(6 channels)
Channel
Function
Value 0-255
instruction
1
LED 1 dimmer
0-255
LED 1 dimmer 0-100%
2
LED 2 dimmer
0-255
LED 2 dimmer 0-100%
3
LED 3 dimmer
0-255
LED 3 dimmer 0-100%
4
LED 4 dimmer
0-255
LED 4 dimmer 0-100%
5
LED 5 dimmer
0-255
LED 5 dimmer 0-100%
6
Color
1-17
red
18-34
green
35-51
blue
52-68
white
69-85
red+green
86-102
red+blue
103-119
red+white
120-136
green+blue

6
6
color
137-153
green+white
154-170
blue+white
171-187
red+green+blue
188-204
red+green+white
205-221
red+blue+white
222-238
green+blue+white
239-255
red+green+blue+white
DMX Channels(7 channels)
Channel
Function
Value 0-255
instruction
1
master dimmer
0-255
master dimmer 0-100%
2
red
0-255
red dimmer 0-100%
3
green
0-255
green dimmer 0-100%
4
blue
0-255
blue dimmer 0-100%
5
white
0-255
white dimmer 0-100%
6
strobe
0-255
strobe 0-100%
7
color marco
0-7
no effect
8-255
color Marco, each 6 value for one color marco
DMX Channels(21 channels)
Channel
Function
Value 0-255
instruction
1
master dimmer
0-255
2
LED 1 red dimmer
0-255
LED 1 red dimmer 0-100%
3
LED 1 green dimmer
0-255
LED 1 green dimmer 0-100%
4
LED 1 blue dimmer
0-255
LED 1 blue dimmer 0-100%
5
LED 1 white dimmer
0-255
LED 1 white dimmer 0-100%
6
LED 2 red dimmer
0-255
LED 2 red dimmer 0-100%
7
LED 2 green dimmer
0-255
LED 2 green dimmer 0-100%
8
LED 2 blue dimmer
0-255
LED 2 blue dimmer 0-100%
9
LED 2 white dimmer
0-255
LED 2 white dimmer 0-100%
10
LED 3 red dimmer
0-255
LED 3 red dimmer 0-100%
11
LED 3 green dimmer
0-255
LED 3 green dimmer 0-100%
12
LED 3 blue dimmer
0-255
LED 3 blue dimmer 0-100%
13
LED 3 white dimmer
0-255
LED 3 white dimmer 0-100%
14
LED 4 red dimmer
0-255
LED 4 red dimmer 0-100%
15
LED 4 green dimmer
0-255
LED 4 green dimmer 0-100%
16
LED 4 blue dimmer
0-255
LED 4 blue dimmer 0-100%
17
LED 4 white dimmer
0-255
LED 4 white dimmer 0-100%
18
LED 5 red dimmer
0-255
LED 5 red dimmer 0-100%
19
LED 5 green dimmer
0-255
LED 5 green dimmer 0-100%
20
LED 5 blue dimmer
0-255
LED 5 blue dimmer 0-100%
21
LED 5 white dimmer
0-255
LED 5 white dimmer 0-100%

7
DMX Channels(30 channels)
Channel
Function
Value 0-255
instruction
1
LED 1 master dimmer
0-255
LED 1 master dimmer 0-100%
2
LED 1 red dimmer
0-255
LED 1 red dimmer 0-100%
3
LED 1 green dimmer
0-255
LED 1 green dimmer 0-100%
4
LED 1 blue dimmer
0-255
LED 1 blue dimmer 0-100%
5
LED 1 white dimmer
0-255
LED 1 white dimmer 0-100%
6
LED 1 strobe
0-255
LED 1 strobe
7
LED 2 master dimmer
0-255
LED 2 master dimmer 0-100%
8
LED 2 red dimmer
0-255
LED 2 red dimmer 0-100%
9
LED 2 green dimmer
0-255
LED 2 green dimmer 0-100%
10
LED 2 blue dimmer
0-255
LED 2 blue dimmer 0-100%
11
LED 2 white dimmer
0-255
LED 2 white dimmer 0-100%
12
LED 2 strobe
0-255
LED 2 strobe
13
LED 3 master dimmer
0-255
LED 3 master dimmer 0-100%
14
LED 3 red dimmer
0-255
LED 3 red dimmer 0-100%
15
LED 3 green dimmer
0-255
LED 3 green dimmer 0-100%
16
LED 3 blue dimmer
0-255
LED 3 blue dimmer 0-100%
17
LED 3 white dimmer
0-255
LED 3 white dimmer 0-100%
18
LED 3 strobe
0-255
LED 3 strobe
19
LED 4 master dimmer
0-255
LED 4 master dimmer 0-100%
20
LED 4 red dimmer
0-255
LED 4 red dimmer 0-100%
21
LED 4 green dimmer
0-255
LED 4 green dimmer 0-100%
22
LED 4 blue dimmer
0-255
LED 4 blue dimmer 0-100%
23
LED 4 white dimmer
0-255
LED 4 white dimmer 0-100%
24
LED 4 strobe
0-255
LED 4 strobe
25
LED 5 master dimmer
0-255
LED 5 master dimmer 0-100%
26
LED 5 red dimmer
0-255
LED 5 red dimmer 0-100%
27
LED 5 green dimmer
0-255
LED 5 green dimmer 0-100%
28
LED 5 blue dimmer
0-255
LED 5 blue dimmer 0-100%
29
LED 5 white dimmer
0-255
LED 5 white dimmer 0-100%
30
LED 5 strobe
0-255
LED 5 strobe

8
5.Trouble Shooting
F ollo w ing a r e a few c o mm on p r oble m s th a t m a y occu r d uring ope r a tion . He r e a r e s o m e s ug g es tion s fo r
ea s y tr ou b leshooting :
A. The un it does no t work , no li ght a n d t he f a n d o es no t w o r k
1. Check th e c on nect ion of p owe r a nd m a in fu s e .
2. M eas ure th e m a ins volt a ge on th e m a i n co nn e ct o r .
3. Check th e pow er on LED .
B. N o t responding t o D MX c on t ro ll er
1. D M X LED s h ou ld b e on. If no t, che ck D M X co n nectors, ca b l es to s ee if link p r ope r ly .
2. If th e D M X LE D i s on a nd no r espons e t o th e c h a nn el, che ck th e a dd r ess s etti ng s a nd D M X p ol a r ity .
3. If y ou h a ve i nter m ittent D M X s ig n a l p r oble m s , che ck th e p ins on c onn ecto r s or on
PCB of th e u nit or the p r ev iou s on e.
4. Tr y to us e a no th er D M X co ntroller .
5. Check if th e D M X ca b le s r un ne a r or run a lon g s id e t o h ig h volta ge c a b les th a t m a y c a us e d a m a ge or
in terfer ence to D M X inter face circui t.
C . One of the cha nn el s is no t w o r k ing w el l
1. Th e s tep p er moto r m ig h t b e dam a g ed or the c a b le c on nect ed to th e PCB is b r oken.
2. Th e m oto r ’ s d r ive IC on th e PCB m ig h t b e o ut of co ndition
6.Fixture Cleaning
The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp,
smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s optics.
Clean with soft cloth using normal glass cleaning fluid.
Always dry the parts carefully.
Clean the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.