Uplus Lighting W3725 User manual

User manual
W3725
Please read the instructions carefully before use

2
TABLE OF CONTENTS
1. Safety Instructions……………………………………………………………………………3-4
Technical Specifications…………………………………………………………………………4
Control Menu ……………………………………………………………………………………5-6
DMX Channels ……………………………………………………………………………………6-8
Dimension …………………………………………………………………………………………9
Trouble Shooting…………………………………………………………………………………10
Fixture Cleaning………………………………………………………… ………………………10
STATEMENT
The product has well capability and intact packing when leave factory. All of the user should
comply with warning item and manual, any misuse cause of the damages are not included in our
guarantee, and also can not be responsible for any malfunction & problem owing to ignore the
manual.

3
1.Safety Instructions
Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that
they also receive this instruction booklet.
•Unpack and check carefully there is no transportation damage before using the unit.
•Before operating, ensure that the voltage and frequency of power supply match the power
requirements of the unit.
•It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
•The unit is for indoor use only. Use only in a dry location.
•The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent
surfaces. Be sure that no ventilation slots are blocked.
•Disconnect main power before replacement or servicing.
•Make sure there are no flammable materials close to the unit while operating as it is fire hazard.
•Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but always
by taking its base.
•Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is higher
than this Unit surface temperature may reach up to 85℃. DO NOT touch the housing bare-hand
during its operation. Turn off the power and allow about 15 minutes for the unit to cool down before
replacing or serving.
•the event of serious operating problem, stop using the unit immediately.Never try to repair the unit
by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please
contact the nearest authorized technical assistance center. Always use the same type spare parts.
•DO NOT touch any wire during operation as high voltage might be causing electric shock.
Warning:
•To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture.
•The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.
Caution:
•There are no user serviceable parts inside the unit. DO NOT open the housing or attempt any
repairs yourself. In the unlikely event your unit may require service, please contact your nearest
dealer.
Installation:

4
•The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly
fixed to avoid vibration and slipping while operating. And make sure that the structure to which you
are attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight. Also
always use a safety cable that can hold 12 times of the weight of the unit when installing the fixture.
•The equipment must be fixed by professionals. And it must be fixed at a place where is out of the
touch of people.
2.Technical Specifications
Power supply: 110-240V, 50/60HZ
Power consumption: 850W
Light source:37x25W 4inl RGBW LED
DMX Channel:19/36CH
Zoom angle: 10°- 60 °
Horizontal scanning: 540° (16bit precision scanning) Electronic error correction
Vertical scanning: 270° (16bit precision scanning) Electronic error correction
Construction
Data In/Out : 3-pin XLP socket
Power in/Out : Power Con in / out
Protection Rating: IP20
Strobe: 1-25 times/S or random strobe
Dimming: 0-100% linear adjustment
Dimensions : 465*410*200mm
N Weight: 16.2kgs

5
3.Control Menu
1. Function Display:
Shows the various menus and the selected functions
2.LED：
POWER
ON
Power On
DMX
ON
DMX input present
3. Button:
MENU
To select the programming functions
DOWN
To go backward in the selected functions
UP
To go forward in the selected functions
ENTER
To confirm the selected functions
4. DMX IN:
DMX512 link, use 3/5‐pin XLR cable to link the unit and the DMX controller
5. DMX OUT:
DMX512 link, use 3/5‐pin XLR cable to link the next unit and output DMX signal
6. MAINS IN:
PowerCon connection from main power supply
7. MAIS OUT:
PowerCon loop connection for main power supply to the next unit
8. Fuse (T 10A):
Protects the unit from over‐voltage or short circuit
To select any of the given functions, press the MENU button until the required function is showing on the display.
Select the function by pressing the ENTER button and the display will blink. Use the
DOWN/UP buttons to change the mode. Once the required mode has been selected, press the ENTER button to
setup, to go back to the functions without any change press the MENU button again. Press and hold the MENU
button for about one second or wait for one minute to exit the menu mode.
The main functions are shown overleaf:

6
4.DMX Channels
19 CH Mode
19CH
Function
DMX Values
Details
CH1
Pan
0-255
0-540°
CH2
Pan Fine
0-255
16 bit
CH3
Tilt
0-255
0-270°
CH4
Tilt Fine
0-255
16 bit
CH5
P/T speed
0-255
From slow to fast
CH6
Zoom
0-255
wide to narrow
CH7
SPECIAL FUNCTIONS
000‐009
No function
010‐014
Reset
015‐255
No function
CH8
Dimmer
0-255
Linear dimmer （dark to brightness)
CH9
shutter effect
000‐019
Blackout
020‐024
Open
025‐064
Strobe 1: fast slow

7
CH9
shutter effect
065‐069
Open
070‐084
Strobe 2: opening pulse, fast slow
085‐089
Open
090‐104
Strobe 3: closing pulse, fast slow
105‐109
Open
110‐124
Strobe 4: random strobe, fast slow
125‐129
Open
130‐144
Strobe 5: random opening pulse, fast slow
145‐149
Open
150‐164
Strobe 6: random closing pulse, fast slow
165‐169
Open
170‐184
Strobe 7: burst pulse, fast slow
185‐189
Open
190‐204
Strobe 8: random burst pulse, fast slow
205‐209
Open
210‐224
Strobe 9: sine wave, fast slow
225‐229
Open
230‐244
Strobe 10: burst, fast slow
245‐255
Open
CH10
Red
0-255
0- 100%
CH11
Green
0-255
0- 100%
CH12
Blue
0-255
0- 100%
CH13
White
0-255
0- 100%
CH14
COLOR
000-255
COLOR
CH15
COLOR CHANGE SPEED
000-255
COLOR CHANGE SPEED (OPEN 17-CH 020-029)
CH16
COLOR FADE SPEED
000-255
COLOR FADE SPEED (OPEN 17-CH 030-039)
CH17
COLOR MARCO
0-19
Overall Control
20-29
Color Change
30-39
Color Gradient Change
40-255
Built-in programs
CH18
MARCO SPEED
0-255
MARCO SPEED (OPEN 17-CH 040-255)
CH19
COLOR TEMPERATURE
0-255
COLOR TEMPERATURE
36 CH Mode
36CH
Function
DMX Values
Details
CH1
Pan
0-255
0-540°
CH2
Pan Fine
0-255
16 bit
CH3
Tilt
0-255
0-270°
CH4
Tilt Fine
0-255
16 bit
CH5
P/T speed
0-255
From slow to fast
CH6
Zoom
0-255
wide to narrow
CH7
SPECIAL FUNCTIONS
000‐009
No function
010‐014
Reset
015‐255
No function
CH8
Dimmer
0-255
Linear dimmer （dark to brightness)
CH9
shutter effect
000‐019
Blackout
020‐024
Open
025‐064
Strobe 1: fast slow
065‐069
Open
070‐084
Strobe 2: opening pulse, fast slow

8
CH9
shutter effect
085‐089
Open
090‐104
Strobe 3: closing pulse, fast slow
105‐109
Open
110‐124
Strobe 4: random strobe, fast slow
125‐129
Open
130‐144
Strobe 5: random opening pulse, fast slow
145‐149
Open
150‐164
Strobe 6: random closing pulse, fast slow
165‐169
Open
170‐184
Strobe 7: burst pulse, fast slow
185‐189
Open
190‐204
Strobe 8: random burst pulse, fast slow
205‐209
Open
210‐224
Strobe 9: sine wave, fast slow
225‐229
Open
230‐244
Strobe 10: burst, fast slow
245‐255
Open
CH10
Red 1
0-255
0- 100%
CH11
Green 1
0-255
0- 100%
CH12
Blue 1
0-255
0- 100%
CH13
White 1
0-255
0- 100%
CH14
COLOR 1
0- 100%
CH15
Red 2
0-255
0- 100%
CH16
Green 2
0-255
0- 100%
CH17
Blue 2
0-255
0- 100%
CH18
White 2
0-255
0- 100%
CH19
COLOR 2
0- 100%
CH20
Red 3
0-255
0- 100%
CH21
Green 3
0-255
0- 100%
CH22
Blue 3
0-255
0- 100%
CH23
White 3
0-255
0- 100%
CH24
COLOR 3
000-255
0- 100%
CH25
RING MARCO
092‐099
RING MARCO
CH26
RING MARCO SPEED
100‐106
RING MARCO SPEED
CH27
COLOR TEMPERATURE
107‐113
COLOR TEMPERATURE
CH28
RED
114‐121
RED
CH29
GREEN
122‐128
GREEN
CH30
BLUE
129‐136
BLUE
CH31
WHITE
137‐143
WHITE
CH32
COLOR
144‐151
COLOR
CH33
COLOR CHANGE SPEED
152‐158
COLOR CHANGE SPEED (OPEN 35-CH 020-029)
CH34
COLOR FADE SPEED
159‐165
COLOR FADE SPEED (OPEN 35-CH 030-039)
CH35
COLOR MARCO
000-009
Ring Control
010-019
Overall Control
020-029
Color Change
030-039
Color Gradient Change
040-255
Built-in programs
CH36
MARCO SPEED
000-255
MARCO SPEED (OPEN 35-CH 040-255)

9
5.Dimension

10
6.Trouble Shooting
F ollo w ing a r e a few c o mm on p r oble m s th a t m a y occu r d uring ope r a tion . He r e a r e s o m e s ug g es tion s fo r
ea s y tr ou b leshooting :
A. The un it does no t work , no li ght a n d t he f a n d o es no t w o r k
1. Check th e c on nect ion of p owe r a nd m a in fu s e .
2. M eas ure th e m a ins volt a ge on th e m a i n co nn e ct o r .
3. Check th e pow er on LED .
B. N o t responding t o D MX c on t ro ll er
1. D M X LED s h ou ld b e on. If no t, che ck D M X co n nectors, ca b l es to s ee if link p r ope r ly .
2. If th e D M X LE D i s on a nd no r espons e t o th e c h a nn el, che ck th e a dd r ess s etti ng s a nd D M X p ol a r ity .
3. If y ou h a ve i nter m ittent D M X s ig n a l p r oble m s , che ck th e p ins on c onn ecto r s or on
PCB of th e u nit or the p r ev iou s on e.
4. Tr y to us e a no th er D M X co ntroller .
5. Check if th e D M X ca b le s r un ne a r or run a lon g s id e t o h ig h volta ge c a b les th a t m a y c a us e d a m a ge or
in terfer ence to D M X inter face circui t.
C . One of the cha nn el s is no t w o r k ing w el l
1. Th e s tep p er moto r m ig h t b e dam a g ed or the c a b le c on nect ed to th e PCB is b r oken.
2. Th e m oto r ’ s d r ive IC on th e PCB m ig h t b e o ut of co ndition
7.Fixture Cleaning
The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp,
smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s optics.
Clean with soft cloth using normal glass cleaning fluid.
Always dry the parts carefully.
Clean the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.