Uplus Lighting 230 BEAM User manual

User manual
230 BEAM
Please read the instructions carefully before use

2
TABLE OF CONTENTS
1. Safety Instructions……………………………………………………………………………3-4
Technical Specifications…………………………………………………………………………4
Control Menu ……………………………………………………………………………………5-6
DMX Channels ……………………………………………………………………………………7-9
Trouble Shooting…………………………………………………………………………………10
Fixture Cleaning………………………………………………………… ………………………10
STATEMENT
The product has well capability and intact packing when leave factory. All of the user should
comply with warning item and manual, any misuse cause of the damages are not included in our
guarantee, and also can not be responsible for any malfunction & problem owing to ignore the
manual.

3
1.Safety Instructions
Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that
they also receive this instruction booklet.
•Unpack and check carefully there is no transportation damage before using the unit.
•Before operating, ensure that the voltage and frequency of power supply match the power
requirements of the unit.
•It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
•The unit is for indoor use only. Use only in a dry location.
•The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent
surfaces. Be sure that no ventilation slots are blocked.
•Disconnect main power before replacement or servicing.
•Make sure there are no flammable materials close to the unit while operating as it is fire hazard.
•Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but always
by taking its base.
•Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is higher
than this Unit surface temperature may reach up to 85℃. DO NOT touch the housing bare-hand
during its operation. Turn off the power and allow about 15 minutes for the unit to cool down before
replacing or serving.
•the event of serious operating problem, stop using the unit immediately.Never try to repair the unit
by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please
contact the nearest authorized technical assistance center. Always use the same type spare parts.
•DO NOT touch any wire during operation as high voltage might be causing electric shock.
Warning:
•To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture.
•The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.
Caution:
•There are no user serviceable parts inside the unit. DO NOT open the housing or attempt any
repairs yourself. In the unlikely event your unit may require service, please contact your nearest
dealer.
Installation:
•The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly

4
fixed to avoid vibration and slipping while operating. And make sure that the structure to which you
are attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight. Also
always use a safety cable that can hold 12 times of the weight of the unit when installing the fixture.
•The equipment must be fixed by professionals. And it must be fixed at a place where is out of the
touch of people.
2.Technical Specifications
lamp: 230w (life:2200 hours Color temperature: 8000K)
Beam angle:2°
Channel mode:18 Channel
Pan scan：540°(16bit) Electric correction
Tilt scan：270° (16bit) Electric correction
Color wheel: 14 colors
Gobo: 14 gobos
8+16+24 prism
Frost
Over heat protection
Power Input: 100-240V，50/60Hz
Power Dissipation: 230W
IP level :IP20
Net weight：10.8KG
Gross weight：12kg
Packing Size: 50X34.5X36.5CM

5
3. 3.Control Menu
Operation
1 .Operate light with touch or KEY
The left area is TFT Displayer and touch, chick item or value with finger will to complete operation
of set light setting(parameters) or view light state.
The area on the right hand side is 4 KEY, As auxiliary input interface, if disable touch function,, the
KEYr can been choose to set the parameter.
2 .Parameter value setting
When the selected item is value need to been modified, the dialog shown in Figure 4 will popup.
Figure 4 Dialog of value setting
Modify value：Can quickly modify value via pull the slider to the desired position, or click the
button of ‘up’ or ‘down’ whit finger on the right side to set the exact desired value, another way is roll
encoder on the right hand side of panel.
Apply value：When Value had been modified, Then press the bottom of ‘apply’ in the left corner to
apply to the light, but hav’t saved；
Save Value：Any time, click on the lower right corner of the "OK" button, the setting will been saved
into internal memory.
3. Boolean parameter setting
when the selected parameters is a Boolean value (such as ON or OFF), can directly modify setting
by chick corresponding item, the setting will been saved right now.
When the parameter is a key item, chick corresponding item, a dialog shown in Figure 5 will been
popup ask for the confirm. Chick ‘sure’ to confirm.
Figure 5 Dialog of confirm

6
4. Sub Menu（Parameter）
Chick item of main menu, enter corresponding sub menu, shown in Figure 6, total 6 sub menu,
includes class of parameter and status:
ADDRESS：Set light DMX address.
WORKMOD：Set light work mode, master or slave mode when in auto run mode.
DISPLAY：Set display parameter, eg. select language.
TEST：Used for test light, modify DMX channel data to test function，the corresponding function
of reference channel function table.
ADVANCE：Set light running parameter.
STATUS：view light current status.
Figure 6 Parameter menu

7
4.DMX Channels
16 DMX512 Channel
Channel
Name
Data
Introduce
1
Color
0-4
White
5-9
White+Color1
10-14
Color1
15-19
Color1+Color2
20-24
Color2
25-29
Color2+Color3
30-34
Color3
35-39
Color3+Color4
40-44
Color4
45-49
Color4+Color5
50-54
Color5
55-59
Color5+Color6
60-64
Color6
65-69
Color6+Color7
70-74
Color7
75-79
Color7+Color8
80-84
Color8
85-89
Color8+Color9
90-94
Color9
95-99
Color9+Color10
100-104
Color10
105-109
Color10~Color11
110-114
Color11
115-119
Color11+Color12
120-124
Color12
125-129
Color12+Color13
130-134
Color13
135-139
Color13+Color14
140-144
Color14
145-149
Color14+White
150-200
Forwards rainbow from fast to
slow
201-255
Backwards rainbow from slow to
fast

8
2
Strobe
0-3
Close
4-103
Fadeout slow to fast
104-107
Open
108-207
Free Strobe slow to fast
208-212
Open
213-251
Pulse Strobe slow to fast
252-255
Open
3
Dimmer
0-255
Dimmer intensity from 0% to 100%
4
Gobo
0-4
White
5-9
Gobo1
10-14
Gobo2
15-19
Gobo3
20-24
Gobo4
25-29
Gobo5
30-34
Gobo6
35-39
Gobo7
40-44
Gobo8
45-49
Gobo9
50-54
Gobo10
55-59
Gobo11
60-64
Gobo12
65-69
Gobo13
70-125
Forwards rainbow from fast to
slow
126-130
Stop
131-190
Backwards rainbow from slow to
fast
191-195
Gobo1 Shake，Slow to fast
196-200
Gobo2 Shake，Slow to fast
201-205
Gobo3 Shake，Slow to fast
206-210
Gobo4 Shake，Slow to fast
216-220
Gobo6 Shake，Slow to fast
221-225
Gobo7 Shake，Slow to fast
226-230
Gobo8 Shake，Slow to fast
231-235
Gobo9 Shake，Slow to fast
236-240
Gobo10 Shake，Slow to fast
241-245
Gobo11 Shake，Slow to fast
246-250
Gobo12 Shake，Slow to fast
251-255
Gobo13 Shake，Slow to fast

9
5
Prism
0-127
Close Prism
128-255
Insert Prism
6
Prism.Rot
0-127
0~400 degree
128-187
Forwards rainbow from fast to
slow
188-195
Stop
196-255
Backwards rainbow from slow to
fast
7
Colorful
0-127
128-255
Insert colorful
8
Frost
0-127
128-255
Insert frost
9
Zoom
0-255
Zoom Large to small
10
PAN
0-255
Pan movement by 540
11
PAN fine
0-255
Tilt movement by 270
12
TILT
0-255
Fine control of pan movement
13
TILT fine
0-255
Fine control of tilt movement
14
Macro Function
0-255
Close frost
15
Reset
100-105
Lamp Off (Over 3 seconds)
200-205
Lamp on（Over 3 seconds）
210-215
Reset XY(over 3 seconds)
220-235
Reset effect moto(over 3 seconds)
240-255
Reset all(over 3 seconds)
16
lamp open
200-205
open
26-100
Shut down
17
Led Strips
0-255
Led Strips Effect
18
Led Strips
Speed
0-255
Slow to Fast

10
5.Trouble Shooting
F ollo w ing a r e a few c o mm on p r oble m s th a t m a y occu r d uring ope r a tion . He r e a r e s o m e s ug g es tion s fo r
ea s y tr ou b leshooting :
A. The un it does no t work , no li ght a n d t he f a n d o es no t w o r k
1. Check th e c on nect ion of p owe r a nd m a in fu s e .
2. M eas ure th e m a ins volt a ge on th e m a i n co nn e ct o r .
3. Check th e pow er on LED .
B. N o t responding t o D MX c on t ro ll er
1. D M X LED s h ou ld b e on. If no t, che ck D M X co n nectors, ca b l es to s ee if link p r ope r ly .
2. If th e D M X LE D i s on a nd no r espons e t o th e c h a nn el, che ck th e a dd r ess s etti ng s a nd D M X p ol a r ity .
3. If y ou h a ve i nter m ittent D M X s ig n a l p r oble m s , che ck th e p ins on c onn ecto r s or on
PCB of th e u nit or the p r ev iou s on e.
4. Tr y to us e a no th er D M X co ntroller .
5. Check if th e D M X ca b le s r un ne a r or run a lon g s id e t o h ig h volta ge c a b les th a t m a y c a us e d a m a ge or
in terfer ence to D M X inter face circui t.
C . One of the cha nn el s is no t w o r k ing w el l
1. Th e s tep p er moto r m ig h t b e dam a g ed or the c a b le c on nect ed to th e PCB is b r oken.
2. Th e m oto r ’ s d r ive IC on th e PCB m ig h t b e o ut of co ndition
6.Fixture Cleaning
The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp,
smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s optics.
Clean with soft cloth using normal glass cleaning fluid.
Always dry the parts carefully.
Clean the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.