Uplus Lighting 4020 IP User manual

User manual
4020 IP
Please read the instructions carefully before use

2
TABLE OF CONTENTS
1. Safety Instructions……………………………………………………………………………3-4
Technical Specifications………………………………………………………………………4
Control Menu ……………………………………………………………………………………5-6
DMX Channels ……………………………………………………………………………………6
Trouble Shooting…………………………………………………………………………………7
Fixture Cleaning………………………………………………………… ………………………7
STATEMENT
The product has well capability and intact packing when leave factory. All of the user should
comply with warning item and manual, any misuse cause of the damages are not included in our
guarantee, and also can not be responsible for any malfunction & problem owing to ignore the
manual.

3
1.Safety Instructions
Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that
they also receive this instruction booklet.
•Unpack and check carefully there is no transportation damage before using the unit.
•Before operating, ensure that the voltage and frequency of power supply match the power
requirements of the unit.
•It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
•The unit is for indoor use only. Use only in a dry location.
•The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent
surfaces. Be sure that no ventilation slots are blocked.
•Disconnect main power before replacement or servicing.
•Make sure there are no flammable materials close to the unit while operating as it is fire hazard.
•Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but always
by taking its base.
•Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is higher
than this Unit surface temperature may reach up to 85℃. DO NOT touch the housing bare-hand
during its operation. Turn off the power and allow about 15 minutes for the unit to cool down before
replacing or serving.
•the event of serious operating problem, stop using the unit immediately.Never try to repair the unit
by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please
contact the nearest authorized technical assistance center. Always use the same type spare parts.
•DO NOT touch any wire during operation as high voltage might be causing electric shock.
Warning:
•To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture.
•The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.
Caution:
•There are no user serviceable parts inside the unit. DO NOT open the housing or attempt any
repairs yourself. In the unlikely event your unit may require service, please contact your nearest
dealer.
Installation:
•The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly

4
fixed to avoid vibration and slipping while operating. And make sure that the structure to which you
are attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight. Also
always use a safety cable that can hold 12 times of the weight of the unit when installing the fixture.
•The equipment must be fixed by professionals. And it must be fixed at a place where is out of the
touch of people.
2.Technical Specificationst
Operating Conditions
Mains voltage: 100-240V AC / 50-60Hz
Power: 800W
Beam andle:25°（15°/45°/60°optional)
Light source:40x20w RGBW 4in1 LED
IP Rating:IP65
Lifespan:around 100,000hours
Control:DMX512,4/6/9CH
Control Mode:DMX,Auto,Master,Slave mode
Dimmer:0-100%
Strobe：0-20HZ
Housing: Die-casting aluminum, powder-coated finish
Display: LCD color display with 4 touch buttons
NW：17KG

5
3.Control Menu
Display:
MENU To select the programming functions (press to unlock screen)
DOWN To go backward in the selected functions
UP To go forward in the selected functions
ENTER To confirm the selected functions
Set DMX Address:
1. Press "MENU" to unlock screen, then select the “DMX Address” and press "ENTER".
2. Showing "Set DMX Address 001", Press the "UP or DOWN" key to increase or decrease the
DMX address value.
Press "ENTER" to save and Exit, Press "Cancel" does not save and Exit
Main Menu
Sub-Menu1
Sub-Menu
2
Instruction
Address
001-512
DMX addr es s,
001-512
Manu al
Red
000-255
Red Brig ht ness
000-255
Green
000-255
Green Brightnes s
000-255
Blue
000-255
Blue Br ightness
000-255
White
000-255
Whit e Brig ht ness
000-255
Dimm er
000-255
Dimm er,000-255
Strobe
000-255
Strobe, speed 000-255
Au to
7 color
000-099
7 colors cha nge
7 fade
000-099
7 colors fade
7 br eathe
000-099
7 color pulse
Strobe 1
000-099
St robe 1
Strobe 2
000-099
St robe 2
Se tting
DM X
Pe rso n
4C H/6C
H/
9C H
Channel mode: 4CH
/6CH/9CH
Dis play
INV
ON
Di splay Inverse ON
OF F
Di splay Inverse OFF
Ba ck light
OP EN
Ba ck light keep
opening
30S
Ba ck light 30S OFF
60S
Ba ck light 60S OFF

6
4.DMX Channels
4/6/9 Channel mode
Dim mer
Mode
DI M1
Di mmer mo de 1
DI M2
Di mmer mo de 2
DI M3
Di mmer mo de 3
DI M4
Di mmer mo de 4
Fan Mode
AU TO
Fan Au to
HI GH
Fan high spe ed
LO W
Fan low speed
KEY Loc k
OF F
Ke y Lock OF F
ON
Ke y Loc k ON, Aft er
turn ON this fun ction,
enter the pas sword UP
DOWN UP DOW N UP
DOWN UP DOW N th en
pr ess EN TER to enable
key operation
De fau lt
NO
Factory Reset NO
YE S
Factory Reset YES
Lang uage
En glish
Language English
Ch inese
Language Chinese
In fo
VER:02
So ftw are version
RUN TI ME
Ru nning time
4C
H
6C
H
9C
H
Function
Value
Instruction
1
1
Dimmer
0-255
Dimmer, from dark to bright
2
2
Strobe
0-12
No function
13-255
Strobe from slow to fast
1
3
3
Red Dimming
0-255
Red Dimming, from dark to bright
2
4
4
Green
Dimming
0-255
Green Dimming, from dark to bright
3
5
5
Blue Dimming
0-255
Blue Dimming, from dark to bright
4
6
6
White
Dimming
0-255
White Dimming, from dark to bright
7
Color
Selection
0-31
No function
32-63
Red
64-95
Green
96-127
Blue
128-159
White
160-191
Red+Green
192-223
Red+Blue
224-255
Green+Blue
8
Macro
Function
0-50
No function
101-150
Color Change
151-200
Color Gradual
201-255
Color Pulse
9
Speed
0-255
Speed from slow to fast

7
5.Trouble Shooting
F ollo w ing a r e a few c o mm on p r oble m s th a t m a y occu r d uring ope r a tion . He r e a r e s o m e s ug g es tion s fo r
ea s y tr ou b leshooting :
A. The un it does no t work , no li ght a n d t he f a n d o es no t w o r k
1. Check th e c on nect ion of p owe r a nd m a in fu s e .
2. M eas ure th e m a ins volt a ge on th e m a i n co nn e ct o r .
3. Check th e pow er on LED .
B. N o t responding t o D MX c on t ro ll er
1. D M X LED s h ou ld b e on. If no t, che ck D M X co n nectors, ca b l es to s ee if link p r ope r ly .
2. If th e D M X LE D i s on a nd no r espons e t o th e c h a nn el, che ck th e a dd r ess s etti ng s a nd D M X p ol a r ity .
3. If y ou h a ve i nter m ittent D M X s ig n a l p r oble m s , che ck th e p ins on c onn ecto r s or on
PCB of th e u nit or the p r ev iou s on e.
4. Tr y to us e a no th er D M X co ntroller .
5. Check if th e D M X ca b le s r un ne a r or run a lon g s id e t o h ig h volta ge c a b les th a t m a y c a us e d a m a ge or
in terfer ence to D M X inter face circui t.
C . One of the cha nn el s is no t w o r k ing w el l
1. Th e s tep p er moto r m ig h t b e dam a g ed or the c a b le c on nect ed to th e PCB is b r oken.
2. Th e m oto r ’ s d r ive IC on th e PCB m ig h t b e o ut of co ndition
6.Fixture Cleaning
The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp,
smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s optics.
Clean with soft cloth using normal glass cleaning fluid.
Always dry the parts carefully.
Clean the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.