Uplus Lighting 10X30 COB BAR User manual

User manual
10X30 COB BAR
Please read the instructions carefully before use

2
TABLE OF CONTENTS
1. Safety Instructions……………………………………………………………………………3-4
2.Technical Specifications…………………………………………………………………………4
3.Control Menu ………………………………………………………………………………………5
4.DMX Channels …………………………………………………………………………………6-7
5.Trouble Shooting…………………………………………………………………………………9
6.Fixture Cleaning………………………………………………………… ………………………9
STATEMENT
The product has well capability and intact packing when leave factory. All of the user should
comply with warning item and manual, any misuse cause of the damages are not included in our
guarantee, and also can not be responsible for any malfunction & problem owing to ignore the
manual.

3
1.Safety Instructions
Please keep this User Guide for future consultation. If you sell the unit to another user, be sure
that they also receive this instruction booklet.
•Unpack and check carefully there is no transportation damage before using the unit.
•Before operating, ensure that the voltage and frequency of power supply match the power
requirements of the unit.
•It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
•The unit is for indoor use only. Use only in a dry location.
•The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent
surfaces. Be sure that no ventilation slots are blocked.
•Disconnect main power before replacement or servicing.
•Make sure there are no flammable materials close to the unit while operating as it is fire hazard.
•Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but always
by taking its base.
•Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is higher
than this Unit surface temperature may reach up to 85℃. DO NOT touch the housing bare-hand
during its operation. Turn off the power and allow about 15 minutes for the unit to cool down before
replacing or serving.
•the event of serious operating problem, stop using the unit immediately.Never try to repair the unit
by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please
contact the nearest authorized technical assistance center. Always use the same type spare parts.
•DO NOT touch any wire during operation as high voltage might be causing electric shock.
Warning:
•To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture.
•The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.
Caution:
•There are no user serviceable parts inside the unit. DO NOT open the housing or attempt any
repairs yourself. In the unlikely event your unit may require service, please contact your nearest
dealer.
Installation:
•The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is

4
firmly fixed to avoid vibration and slipping while operating. And make sure that the structure to
which you are attaching the unit is secure and is able to support a weight of 10 times of the unit’s
weight. Also always use a safety cable that can hold 12 times of the weight of the unit when
installing the fixture.
•The equipment must be fixed by professionals. And it must be fixed at a place where is out of the
touch of people.
2.Technical Specifications
Input Voltage:AC90-240V,50/60Hz
Power Consumption:300W
Light Source:Integrated 30W *10PCS COB RGB 3in1 LED,
Each LED can be controlled individual
Lamp life:50000hrs
Beam Angle:12°/24°/36° (standard make with 24°)
Display :Digital LED display
Control Mode:DMX512,Master/Slave,Auto,Sound Active
DMX Channel:5/14/34 DMX Channels
Dimmer:0-100% smooth linear adjustment
Strobe:High speed strobe effect with 1-25 flashes per second
Cooling mode: Fan cooling(Temperature control)
Fan Control: Adjust fan control according to temperature
Temperature protection: Temperature protection by controlling the output power
Housing Material:Metal plate+Aluminum
Anti-electricity intension：1.5KV
Insulation Resistance：＞２MΩ
IP Rate:IP20
Net Weight:5.3 Kg
Packing size:991*83*170 mm ( include stand bracket)

5
3.Control Menu
Sq.NO.
Display
①
MENU
②
UP
③
DOWN
④
ENTER
Display:
MENU To select the programming functions
DOWN To go backward in the selected functions
UP To go forward in the selected functions
ENTER To confirm the selected functions (unlock screen)
Operations:
Press "MENU" to unlock screen, then press “Menu” to select 7 different functions, Press the "UP
or DOWN"keys to increase or decrease the value,Press "ENTER" to save and Exit.

6
4.DMX Channels
DMX Channels(5 channels)
Channel
Value
Function
Comment
CH 1
0--255
Dimmer,0-100%
CH 2
0—255
Red,0-100%
CH 3
0—255
Green,0-100%
CH 4
0--255
Blue,0-100%
CH 5
0--007
Open
008--015
Black out
016--131
Strobe,slow to fast
132--139
Open
140—181
LED slow open，fast close,slow to fast
182—189
Open
190--231
LED fast open，slow close,slow to fast
232--239
Open
240--247
Random strobe
248--255
Open
DMX Channels(14 channels)
Channel
Value
Function
Comment
CH 1
0--255
Dimmer,0-100%
CH 2
0—255
LED1 COLOR,0-100%
CH 3
0—255
LED2 COLOR,0-100%
CH 4
0--255
LED3 COLOR,0-100%
CH 5
0--255
LED4 COLOR,0-100%
CH 6
0—255
LED5 COLOR,0-100%
CH 7
0—255
LED6 COLOR,0-100%
CH 8
0--255
LED7 COLOR,0-100%
CH 9
0—255
LED8 COLOR,0-100%
CH 10
0—255
LED9 COLOR,0-100%
CH 11
0--255
LED10 COLOR,0-100%
CH 12
0--007
Open
008--015
Black out
016--131
Strobe,slow to fast
132--139
Open
140—181
LED slow open，fast close,slow to fast
182—189
Open
190--231
LED fast open，slow close,slow to fast
232--239
Open
240--247
Random strobe
248--255
Open
0—007
No function
008—022
SHOW 1
023--037
SHOW 2

7
CH 13
038—052
SHOW 3
053—067
SHOW 4
068—082
SHOW 5
083—097
SHOW 6
098—112
SHOW 7
113—127
SHOW 8
128—142
SHOW 9
143—157
SHOW 10
158—172
SHOW 11
173—187
SHOW 12
188—202
SHOW 13
203—217
SHOW 14
218—232
SHOW 15
233—247
SHOW 16
248--255
Random SHOW
CH 14
0--255
SHOW Speed
From slow to fast
DMX Channels(34 channels)
Channel
Value
Function
Comment
CH 1
0--255
Dimmer,0-100%
CH 2
0—255
Red1,0-100%
CH 3
0—255
Green1,0-100%
CH 4
0--255
Blue1,0-100%
CH 5
0--255
Red2,0-100%
CH 6
0—255
Gree2,0-100%
CH 7
0—255
Blue2,0-100%
CH 8
0--255
Red3,0-100%
CH 9
0—255
Gree3,0-100%
CH 10
0—255
Blue3,0-100%
CH 11
0--255
Red4,0-100%
CH 12
0--255
Gree4,0-100%
CH 13
0—255
Blue4,0-100%
CH 14
0—255
Red5,0-100%
CH 15
0--255
Gree5,0-100%
CH 16
0--255
Blue5,0-100%
CH 17
0—255
Red6,0-100%
CH 18
0—255
Gree6,0-100%
CH 19
0--255
Blue6,0-100%
CH 20
0—255
Red7,0-100%
CH 21
0—255
Gree7,0-100%
CH 22
0--255
Blue7,0-100%
CH 23
0--255
Red8,0-100%
CH 24
0—255
Gree8,0-100%
CH 25
0—255
Blue8,0-100%
CH 26
0--255
Red9,0-100%
CH 27
0--255
Gree9,0-100%
CH 28
0—255
Blue9,0-100%

8
CH 29
0—255
Red10,0-100%
CH 30
0--255
Gree10,0-100%
CH 31
0—255
Blue10,0-100%
CH 32
0--007
Open
008--015
Black out
016--131
Strobe,slow to fast
132--139
Open
140—181
LED slow open，fast close,slow to fast
182—189
Open
190--231
LED fast open，slow close,slow to fast
232--239
Open
240--247
Random strobe
248--255
Open
CH 33
0—007
No function
008—022
SHOW 1
023--037
SHOW 2
038—052
SHOW 3
053—067
SHOW 4
068—082
SHOW 5
083—097
SHOW 6
098—112
SHOW 7
113—127
SHOW 8
128—142
SHOW 9
143—157
SHOW 10
158—172
SHOW 11
173—187
SHOW 12
188—202
SHOW 13
203—217
SHOW 14
218—232
SHOW 15
233—247
SHOW 16
248--255
Random SHOW
CH 34
0--255
SHOW Speed
From slow to fast

9
5.Trouble Shooting
F ollo w ing a r e a few c o mm on p r oble m s th a t m a y occu r d uring ope r a tion . He r e a r e s o m e s ug g es tion s fo r
eas y tr ou b leshooting :
A. The un it does no t work , no li ght a n d t he f a n d o es no t w o r k
1. Check th e c onnect ion of p owe r a nd m a in fu s e .
2. M eas ure th e m a ins volt a ge on th e m a i n co nn e ct o r .
3. Check th e pow er on LED .
B. N o t responding t o D MX c on t ro ll er
1. D M X LED s h ou ld b e on. If no t, che ck D M X co nnect ors, ca b l es to s ee if link p r ope r ly .
2. If th e D M X LE D i s on a nd no r espons e t o th e c h a nn el, che ck th e a dd r ess s etti ng s a nd D M X
pol a rity .
3. If you h a ve i nter mittent D M X s ig n a l p r oble m s , che ck th e p ins on c onnecto r s or on
PCB of th e u nit or the p r ev iou s on e.
4. Tr y to us e a no th er D M X co ntroller .
5. Check if th e D M X ca b le s r un ne a r or run a lon g s id e t o h ig h volta ge c a b les th a t m a y c a us e d a m a ge or
in terfer ence to D M X inter face circui t.
C . One of the cha nn el s is no t w o r k ing w el l
1. Th e s tep p er moto r m ig h t b e dam a g ed or the c a b le c onnect ed to th e PCB is b r oken.
2. Th e m oto r ’ s d r ive IC on th e PCB m ig h t b e o ut of co ndition
6.Fixture Cleaning
The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates:
damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s optics.
Clean with soft cloth using normal glass cleaning fluid.
Always dry the parts carefully.
Clean the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.