Uplus Lighting 280 LED BSW User manual

User manual
280 LED BSW
Please read the instructions carefully before use

2
TABLE OF CONTENTS
1. Safety Instructions………………………………………………………………………………3
Technical Specifications…………………………………………………………………………4
Control Menu ……………………………………………………………………………………5-8
DMX Channel ……………………………………………………………………………………8-10
Dimension…………………………………………………………………………………………10
Trouble Shooting…………………………………………………………………………………11
Fixture Cleaning………………………………………………………… ………………………11
STATEMENT
The product has well capability and intact packing when leave factory. All of the user should
comply with warning item and manual, any misuse cause of the damages are not included in our
guarantee, and also can not be responsible for any malfunction & problem owing to ignore the
manual.

3
1.Safety Instructions
Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that
they also receive this instruction booklet.
•Unpack and check carefully there is no transportation damage before using the unit.
•Before operating, ensure that the voltage and frequency of power supply match the power
requirements of the unit.
•It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
•The unit is for indoor use only. Use only in a dry location.
•The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent
surfaces. Be sure that no ventilation slots are blocked.
•Disconnect main power before replacement or servicing.
•Make sure there are no flammable materials close to the unit while operating as it is fire hazard.
•Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but always
by taking its base.
•Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is higher
than this Unit surface temperature may reach up to 85℃. DO NOT touch the housing bare-hand
during its operation. Turn off the power and allow about 15 minutes for the unit to cool down before
replacing or serving.
•the event of serious operating problem, stop using the unit immediately.Never try to repair the unit
by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please
contact the nearest authorized technical assistance center. Always use the same type spare parts.
•DO NOT touch any wire during operation as high voltage might be causing electric shock.
Warning:
•To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture.
•The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.
Caution:
•There are no user serviceable parts inside the unit. DO NOT open the housing or attempt any
repairs yourself. In the unlikely event your unit may require service, please contact your nearest
dealer.
Installation:
•The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly
fixed to avoid vibration and slipping while operating. And make sure that the structure to which you
are attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight. Also
always use a safety cable that can hold 12 times of the weight of the unit when installing the fixture.
•The equipment must be fixed by professionals. And it must be fixed at a place where is out of the
touch of people.

4
2.Technical Specifications
280W LED BSW 3-in-1 moving head
Optics:
Light Source:280W white LED
beam angle:6°-28°
power:380W
LED color temperature: 8000K
Input voltage:AC100-240V 50-60HZ
Pan movement:540° (16bit precision scan) electronic error correction
Tilt movement:270°(16bit precision scan) electronic error correction
Color: 9 colors + Open，Split Color ,continue bi-directional rotating
Fixed patterns: 12 fixed patterns + white light
Static gobo wheel：9Gobo+Open and gobo shake , gobo continue bi-directional rotating
rotating gobo wheel: 7 gobo + open ,and gobo shake , gobo continue bi-directional rotating
Prism: 8 facet and 6-faced linear facet rotatable prisms
Frost filter for wash effect
fan cooling(fan speed up as per temperature change)
Dimming system: 0-100% linear adjustment
Display mode:2.4inch 180°Reversible color display screen
Features:
Appearance material: high temperature resistant plastic
DMX Channels:20 channels
Control: DMX 512/ master-slave/self-propelled/console reset/RDM
Dimension: 320×236×538 mm, NW:18 kg

5
3.Control Menu
Configuring the Starting Address
Each fixture requires a starting address from 1~512. A fixture requiring one or more channels for control
begins to read the data on the channel indicated by the starting address. For example, a fixture that uses
seven DMX channels and is addressed to start on DMX channel 100, will read data from channels: 100, 101,
102, 103, 104, 105 and 106. Choose the starting addresses for each fixture so that the channels used do not
overlap. In addition, you should note the starting address selected for future reference.
Control Panel Functions
The Control Panel shows the current state of the unit. It is used to select the operating mode, as well as the
sub-features. For a detailed layout of the control panel functions, please see the “menu map” section on the
following page.
[BACK] menu selection or return to previous menu.
[UP] press [UP] through the menu list to increase/change the value of the current function.
[DOWN] press [DOWN] through the menu list to decrease/change the value of the current function.
[RIGHT] press [RIGHT] through the menu list to increase/change the value of the current function.
[OK] confirm & quit out current function setting.
1. Sub Menu（Parameter）
Chick item of main menu, enter corresponding sub menu, shown in figure3, total 6 sub menu, includes class of
parameter and status:
ADDRESS：Set light DMX address.
WORKMOD：Set light work mode, master or slave mode when in auto run mode.
DISPLAY：Set display parameter, eg. select language.
TEST ：Used for test light, modify DMX channel data to test function ，the corresponding function of
reference channel function table.
ADVANCE：Set light running parameter.
STATUS：view light current status.

6
2 Operation and parameter instruction
Via following operation, enter sub menu(parameter menu) shown in figure3
In main menu, click [UP] [DOWN] [RIGHT] [OK] button into corresponding parameter menu.
3Set DMX Address
Click and select the "ADDR", can enter the page of DMX address setting, range from 1 to 512, the address code
shouldn’t is not greater than (512- channels quantity), otherwise the light will not been controlled. Following is the
operation:
Enter the page of DMX address, as shown in Figure4, click [UP] OR [DOWN] chose the address code area,click
[OK] key confirm and then click [UP] and [DOWN] again to modify value, then click ‘ENTER’ to confirm and save
DMX address code.
4 Set Light work mode
Enter the page of ‘WORK MOD’ as shown in figure5 and modify setting. Can set light work mode, control lamp
and DMX channel mode..
Light includes 3 work mode: DMX MODE, AUTO RUN and SOUND MODE, Parameter definition as following:
DMX Mode：Under this mode, the light receive data from the DMX controller and move.
AUTO RUN：Under this mode, light will run with inside code(data), ignore data from DMX controller.
SOUND Ctrl：Under this mode, light ignore data from DMX controller., When there is a strong sound in stage,
the light will run a scene, otherwise it will keep the last scene.
M/S Choose：’M/S Choose’ is available when light just in ‘AUTO RUN’ or ‘SOUND Ctrl’ mode. If this item is
set as ‘OFF’, the light don’t send data to other light via DMX Cable. When ‘ON’, the data will send to other
slave light immediately.

7
5 Set display
Light support 2 language, rotation display，Enter page as shown in figure 6 to set parameter following:
Language：Select display as simplified Chinese or English.
Screen Saver ：when panel is idle(these is no operation in 10 second), displayer will enter saver status.
When set as ‘mode 1’，saver status is close display, as ‘mode 2’ saver status will display DMX address
code(DMX MODE) or display LOGO(AUTO RUN or SOUND CTRL). As ‘OFF’, keep light up displayer and
show main menu。
Screen Rotation：rotate displayer.
Touch enable ：Disable or enable touch function, when disable, use encoder to operate light and set
parameter.
Touch adjust：adjust touch function, normally, not enter this item.
6 Test light
Enter the page as shown in figure 7, Light will into test mode, in this mode, the light does not receive the data for
DMX controller.:
PAN: range for 0 to 255;
TILT: range for 0 to 255;
FOCUS: range for 0 to 255;
COLOR: range for 0 to 255;
GOBO: range for 0 to 255;
PRISM: range for 0 to 255;
FROST: range for 0 to 255;；
STROBE: range for 0 to 255;。
7 Set light run parameter
Enter the page as shown in fugure 8 , set the parameter of light:
Pan Invert: Reverse PAN move.
Tilt Invert: Reverse TILT mover.
Rectify enable：set as ‘OFF’, PAN or TILT will disable position rectify function. As ‘ON’, when PAN or TILT lose
steps, light will rectify auto.
Pan Offset: Set PAN original position.
Tilt Offset: Set TILT original position.

8
Lamp up when: Select lamp on mode, includes 3 mode: power on, after reset done and manual；
Factory setting: restore all parameter to factory setting.
8 View status
Enter the page as shown in figure 3 ,
View light current status, version；
DMXClr: Click to clear all DMX data to ‘0’.
SysRst：Click to reset light.
4.DMX Channels
DMX channel´s functions and values (20DMX channels)
Channel
Function
Value
Description
CH1
Pan
0-255
0-540 degree
CH2
Pan Fine
0-255
0-2 degree
CH3
Tilt
0-255
0-270 degree
CH4
Tilt Fine
0-255
0-1 degree
CH5
Pan/Tilt speed
0-255
From fast to slow
CH6
Dimmer
0-255
Dimmer 0-100%
CH7
Strobe
0-3
No function
4-127
Strobe at linearly variable frequency from slow to fast
128-191
Pulsation at linearly variable speed
192-251
Random strobe
252-255
No function
CH8
Color
0-127
Open/White
128-134
white
135-140
Color 1
141-145
Color 2
146-150
Color 3
151-155
Color 4
156-160
Color 5
161-165
Color 6
166-170
Color 7
171-175
Color 8
176-180
Color 9
181-216
Color auto changing from fast to slow
217-220
stop
221-255
Forwards rainbow effect from fast to slow
201-255
Backwards rainbow effect from slow to fast
CH9
Color fine
0-255

9
CH10
Fix Gobo
0-9
Open
10-19
Gobo 1
20-29
Gobo 2
30-39
Gobo 3
40-49
Gobo 4
50-59
Gobo 5
60-69
Gobo 6
70-79
Gobo 7
80-89
Gobo8
90-99
Gobo 9
100-109
Gobo 1 shake from slow to fast
110-119
Gobo 2 shake from slow to fast
120-129
Gobo 3 shake from slow to fast
130-139
Gobo 4 shake from slow to fast
140-149
Gobo 5 shake from slow to fast
150-159
Gobo 6 shake from slow to fast
160-169
Gobo 7 shake from slow to fast
170-179
Gobo 8 shake from slow to fast
180-189
Gobo 9 shake from slow to fast
190-221
forwards gobo rotation from slow to fast
222-223
stop
224-255
Backwards gobo rotation from slow to fast
CH11
Rot Gobo
0-9
Open
10-19
Gobo 1
20-29
Gobo 2
30-39
Gobo 3
40-49
Gobo 4
50-59
Gobo 5
60-69
Gobo 6
70-79
Gobo 7
80-89
Gobo 1 shake from slow to fast
90-99
Gobo 2 shake from slow to fast
100-109
Gobo 3 shake from slow to fast
110-119
Gobo 4 shake from slow to fast
120-129
Gobo 5 shake from slow to fast
130-139
Gobo 6 shake from slow to fast
140-149
Gobo 7 shake from slow to fast
150-200
Forwards gobo rotation from slow to fast
201-204
STOP
205-255
Backwards gobo rotation from slow to fast
CH12
Gobo Rot
0-127
Rotation from 0-400degree
128-190
Forwards gobo rotation from fast to slow
191-192
Stop
193-255
Backwards gobo rotation from slow to fast
CH13
Gobo rot fine
0-255
CH14
Prism
0-127
No function

10
CH14
prism
128-187
Prism 1
188-195
Prism 2
CH15
Prism rot
0-127
Rotation from 0-400 degree
128-187
Forwards rotation from fast to slow
188-195
Stop
196-255
Backwards rotation from slow to fast
CH16
Frost
0-127
No function
128-255
Frost
CH17
Zoom
0-255
CH18
Focus
0-255
CH19
Focus fine
0-255
CH20
0-49
No function
Auto
50-127
Auto
Reset
128-255
Reset after 6 second
5.Dimension

11
6.Trouble Shooting
F ollo w ing a r e a few c o mm on p r oble m s th a t m a y occu r d uring ope r a tion . He r e a r e s o m e s ug g es tion s fo r
ea s y tr ou b leshooting :
A. The un it does no t work , no li ght a n d t he f a n d o es no t w o r k
1. Check th e c on nect ion of p owe r a nd m a in fu s e .
2. M eas ure th e m a ins volt a ge on th e m a i n co nn e ct o r .
3. Check th e pow er on LED .
B. N o t responding t o D MX c on t ro ll er
1. D M X LED s h ou ld b e on. If no t, che ck D M X co n nectors, ca b l es to s ee if link p r ope r ly .
2. If th e D M X LE D i s on a nd no r espons e t o th e c h a nn el, che ck th e a dd r ess s etti ng s a nd D M X p ol a r ity .
3. If y ou h a ve i nter m ittent D M X s ig n a l p r oble m s , che ck th e p ins on c onn ecto r s or on
PCB of th e u nit or the p r ev iou s on e.
4. Tr y to us e a no th er D M X co ntroller .
5. Check if th e D M X ca b le s r un ne a r or run a lon g s id e t o h ig h volta ge c a b les th a t m a y c a us e d a m a ge or
in terfer ence to D M X inter face circui t.
C . One of the cha nn el s is no t w o r k ing w el l
1. Th e s tep p er moto r m ig h t b e dam a g ed or the c a b le c on nect ed to th e PCB is b r oken.
2. Th e m oto r ’ s d r ive IC on th e PCB m ig h t b e o ut of co ndition
7.Fixture Cleaning
The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp,
smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s optics.
Clean with soft cloth using normal glass cleaning fluid.
Always dry the parts carefully.
Clean the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.