Uplus Lighting PIXEL IP20X15 BAR User manual

User manual
PIXEL IP20X15 BAR
Please read the instructions carefully before use

2
TABLE OF CONTENTS
1. Safety Instructions……………………………………………………………………………3-4
2.Technical Specifications…………………………………………………………………………4
3.Installation…………………………………………………………………………………………5-6
4.Control Menu ………………………………………………………………………………………7
5.DMX Channels …………………………………………………………………………………8-10
6.Dimension…………………………………………………………………………………………11
7.Trouble Shooting…………………………………………………………………………………12
8.Fixture Cleaning………………………………………………………… ………………………12
STATEMENT
The product has well capability and intact packing when leave factory. All of the user should
comply with warning item and manual, any misuse cause of the damages are not included in our
guarantee, and also can not be responsible for any malfunction & problem owing to ignore the
manual.

3
1.Safety Instructions
Please keep this User Guide for future consultation. If you sell the unit to another user, be sure
that they also receive this instruction booklet.
•Unpack and check carefully there is no transportation damage before using the unit.
•Before operating, ensure that the voltage and frequency of power supply match the power
requirements of the unit.
•It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
•The unit is for indoor use only. Use only in a dry location.
•The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent
surfaces. Be sure that no ventilation slots are blocked.
•Disconnect main power before replacement or servicing.
•Make sure there are no flammable materials close to the unit while operating as it is fire hazard.
•Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but always
by taking its base.
•Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is higher
than this Unit surface temperature may reach up to 85℃. DO NOT touch the housing bare-hand
during its operation. Turn off the power and allow about 15 minutes for the unit to cool down before
replacing or serving.
•the event of serious operating problem, stop using the unit immediately.Never try to repair the unit
by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please
contact the nearest authorized technical assistance center. Always use the same type spare parts.
•DO NOT touch any wire during operation as high voltage might be causing electric shock.
Warning:
•To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture.
•The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.
Caution:
•There are no user serviceable parts inside the unit. DO NOT open the housing or attempt any
repairs yourself. In the unlikely event your unit may require service, please contact your nearest
dealer.
Installation:

4
•The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is
firmly fixed to avoid vibration and slipping while operating. And make sure that the structure to
which you are attaching the unit is secure and is able to support a weight of 10 times of the unit’s
weight. Also always use a safety cable that can hold 12 times of the weight of the unit when
installing the fixture.
•The equipment must be fixed by professionals. And it must be fixed at a place where is out of the
touch of people.
2.Technical Specifications
Light Source:
AC90-240V, 50/60HZ
400W power consumption
20 x 15W RGBW 4IN1 LEDs
50,000 hours expected lifetime
6°,8°,12°,15°,25°,45° optional beam angle
Control:
Each LED can be controlled individually
DMX512, RDM, Master-Slave, Auto
11/27/80/91 DMX channels
0-100% 8/16bit linear dimming
1-20 times/second strobe
Construction:
Cast aluminum body
IP65 rating
2 x two quarter-turn locking points for two Omega brackets
Bottom mount for safety wire
Heat sink cooling system
IP65 PowerCON True1 in and out
IP65 DMX in and out
Size and Weight:
Light size: 1004x95x130mm(LxWxH)
Light Net Weight: 9.5KG
Package size(2in1): 1270x320x220mm
Gross weight(2in1): 22.5KG

5
3. Installation
Your IP24X15 BAR can be installed in every kind of following positions.
Please see the explanations and rely to the instructions for a safe operation and secure handling.
Structural Connection
The IP24X15 BAR can be connected using the included quick-release pins. Place the devices next
to each other.
(Insert both Pins to connect the devices)
For the first uses this may be a little hard. Move the devices a little until the Bolts can be inserted
completely. For vertical installation do not exceed the amount of 4 pieces. (caution, provisional
specification) In case of hanging installation, each device needs to be saved individually! Using the
quick-release pins for horizontal installation is not recommended. Each device should individually
be installed with the given installation options below.
Horizontal Installation on the floor
You could place the IP24X15 BAR on the floor by 2 stands. Please make sure the surface is plane
and the reliability of the floor is sufficient.

6
Horizontal hanging with tilt bracket
You can attach the IP24X15 BAR to a Truss or Pipe. Notice that the
tilt bracket(106mm) should face down from the hanging structure. Use the centered holes in the Tilt
Bracket. You can use the additional fix Omega Brackets to hang the device horizontal.
Hanging Vertically “dropped”
Use the vertical Adapter set (including Omega Bracket, optional accessory) to “drop” the IP24X15
BAR from a rigging structure.Notice that we will release a
detailed rigging manual for the different options shortly.
Vertical Installation on the floor
Use the vertical Adapter (optional accessory) in combination with a base plate (optional accessory
). Use the Small standing plate (optional accessory) if
you only wish to install one IP24X15 BAR. If you want to install more than one
device, screw the Small standing plate to a normal truss base plate. We have two kinds of
standing plate, fixed and infinite rotating, for your options.
Notice that we will release a detailed rigging manual for the different options
shortly.
Safety attachment
In any case of rigging the device attach the Safety rope to any of the dedicated eyelets integrated i
nto the sliding brackets.
(Length of Omega & Safety cable position)

7
4.Control Menu
Display:
MENU To select the programming functions
DOWN To go backward in the selected functions
UP To go forward in the selected functions
ENTER To confirm the selected functions (unlock screen)
Operations:
Press "MENU" to unlock screen, then press “Menu” to select 7 different functions, Press the "UP
or DOWN"keys to increase or decrease the value,Press "ENTER" to save and Exit.
Level 1
Level 2
Description
DMX Address
Address
001-512
Set DMX address
DMX
Channel
Mode
DMX_CH7
7 channels DMX mode
DMX_CH14
14 channels DMX mode
DMX_CH42
42 channels DMX mode
DMX_CH15
15 channels DMX mode
DMX_CH43
43 channels DMX mode
Dimmer
Mode
DIM1
Dimmer mode 1
DIM2
Dimmer mode 2
DIM3
Dimmer mode 3
DIM4
Dimmer mode 4
DIM5
Dimmer mode 5
Mode
Selection
DMX512
DMX mode
Auto1
Auto run mode 1
Auto2
Auto run mode 2
Auto3
Auto run mode 3
Y motor
Tilt movement
White
Beam dimmer
W stroboscopic
Beam strobe
Red
Back light red dimmer
Green
Back light green dimmer
Blue
Back light blue dimmer
RGB stroboscopic
Back light strobe
System
Setting
Language
Chinese/English
Bk_Light
OFF/ON
Dmx512
Clear/Keep
W-DMX
Link/Unlink ( W-DMX version only )
System
Info
RDM UID
RDM UID
Version
Software Version Number
DMX Channel
Currently used mode

8
5.DMX Channels
Configuring DMX is described “Setting the DMX mode” on page 17.
Channel
Value
Function
11CH
27CH
80CH
91CH
1
1
*
1
Dimmer :
0-255
All dimmer
2
2
*
2
Strobe :
0-255
Strobe from slow to fast
3
3
*
3
Red :
0-255
Red dimmer
4
4
*
4
Green :
0-255
Green dimmer
5
5
*
5
Blue :
0-255
Blue dimmer
6
6
*
6
White :
0-255
White dimmer
7
7
*
7
Macro :
0-5
Empty
6-14
Macro1(Controlled by CH2-6 )
15-23
Macro2 ( … )
24-32
Macro3 ( … )
33-41
Macro4 ( … )
42-50
Macro5 ( … )
51-59
Macro6 ( … )
60-68
Macro7 ( … )
69-77
Macro8 ( … )
78-86
Macro9 ( … )
87-95
Macro10 ( … )
96-104
Macro11 ( … )
105-113
Macro12 ( … )
114-122
Macro13 ( … )
123-131
Macro14 ( … )
132-140
Macro15 ( … )
141-149
Macro16 ( … )
150-159
Macro17 ( … )
160-167
Macro18 ( … )
168-176
Macro19 ( … )
177-185
Macro20 ( … )
186-194
Macro21 ( … )
195-203
Macro22 ( … )
204-212
Macro23 ( … )
213-221
Macro24 ( … )

9
222-230
Macro25 ( … )
231-239
Macro26 ( … )
240-255
Macro27 ( … )
8
8
*
8
Macro Speed :
0-255
From slow to fast
9
9
*
9
Dimmer Speed :
0-255
From slow to fast
10
10
*
10
RGBW Backlight :
0-255
RGBW Backlight
11
11
*
11
Colour Wheel :
0-1
Empty
2-7
Red
8-14
Rose
...
...
249-255
Colors
*
12
*
*
Red Dimmer LED1-5 :
0-255
Dimmer from dark to bright
*
13
*
*
Green Dimmer LED1-5 :
0-255
Dimmer from dark to bright
*
14
*
*
Blue Dimmer LED1-5 :
0-255
Dimmer from dark to bright
*
15
*
*
White Dimmer LED1-5 :
0-255
Dimmer from dark to bright
*
16
*
*
Red Dimmer LED6-10 :
0-255
Dimmer from dark to bright
*
17
*
*
Green Dimmer LED6-10 :
0-255
Dimmer from dark to bright
*
18
*
*
Blue Dimmer LED6-10 :
0-255
Dimmer from dark to bright
*
19
*
*
White Dimmer LED6-10 :
0-255
Dimmer from dark to bright
*
20
*
*
Red Dimmer LED11-15 :
0-255
Dimmer from dark to bright
*
21
*
*
Green Dimmer LED11-15 :
0-255
Dimmer from dark to bright
*
22
*
*
Blue Dimmer LED11-15 :
0-255
Dimmer from dark to bright
*
23
*
*
White Dimmer LED11-15 :
0-255
Dimmer from dark to bright
*
24
*
*
Red Dimmer LED16-20 :
0-255
Dimmer from dark to bright
*
25
*
*
Green Dimmer LED16-20 :
0-255
Dimmer from dark to bright
*
26
*
*
Blue Dimmer LED16-20 :
0-255
Dimmer from dark to bright

10
*
27
*
*
White Dimmer LED16-20 :
0-255
Dimmer from dark to bright
*
*
1
12
Red 1:
0-255
R1 dimmer
*
*
2
13
Green 1:
0-255
G1 dimmer
*
*
3
14
Blue 1:
0-255
B1 dimmer
*
*
4
15
White 1:
0-255
W1 dimmer
*
*
…
…
…
…
*
*
77
88
Red 20:
0-255
R20 dimmer
*
*
78
89
Green 20:
0-255
G20 dimmer
*
*
79
90
Blue 20:
0-255
B20 dimmer
*
*
80
91
White 20:
0-255
W20 dimmer
Channel
Name
DMX
Value
Description
1
Tilt
0-255
Tilt Movement
2
Beam Dimmer
0-255
Beam Intensity
3
Beam Strobe Mode
0-5
No Strobe
6-42
Strobe Mode 1
43-85
Strobe Mode 2
86-128
Strobe Mode 3
129-171
Strobe Mode 4
172-214
Strobe Mode 5
215-255
Strobe Mode 6
4
Plate Red
0-255
Plate Red Dimmer
5
Plate Green
0-255
Plate Green Dimmer
6
Plate Blue
0-255
Plate Blue Dimmer
7
Plate Strobe
0-9
No Strobe
10-255
Strobe from slow to fast

11
6.Dimension

12
7.Trouble Shooting
F ollo w ing a r e a few c o mm on p r oble m s th a t m a y occu r d uring ope r a tion . He r e a r e s o m e s ug g es tion s fo r
ea s y tr ou b leshooting :
A. The un it does no t work , no li ght a n d t he f a n d o es no t w o r k
1. Check th e c on nect ion of p owe r a nd m a in fu s e .
2. M eas ure th e m a ins volt a ge on th e m a i n co nn e ct o r .
3. Check th e pow er on LED .
B. N o t responding t o D MX c on t ro ll er
1. D M X LED s h ou ld b e on. If no t, che ck D M X co n nectors, ca b l es to s ee if link p r ope r ly .
2. If th e D M X LE D i s on a nd no r espons e t o th e c h a nn el, che ck th e a dd r ess s etti ng s a nd D M X
p ol a r ity .
3. If y ou h a ve i nter m ittent D M X s ig n a l p r oble m s , che ck th e p ins on c onn ecto r s or on
PCB of th e u nit or the p r ev iou s on e.
4. Tr y to us e a no th er D M X co ntroller .
5. Check if th e D M X ca b le s r un ne a r or run a lon g s id e t o h ig h volta ge c a b les th a t m a y c a us e d a m a ge or
in terfer ence to D M X inter face circui t.
C . One of the cha nn el s is no t w o r k ing w el l
1. Th e s tep p er moto r m ig h t b e dam a g ed or the c a b le c on nect ed to th e PCB is b r oken.
2. Th e m oto r ’ s d r ive IC on th e PCB m ig h t b e o ut of co ndition
8.Fixture Cleaning
The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates:
damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s optics.
Clean with soft cloth using normal glass cleaning fluid.
Always dry the parts carefully.
Clean the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.