Wren Kitchens 1000 Base Shallow User manual

For Internal Use: FI.WR.INS.036_WKIN00126_MULTI_1000_2Dr_WALL_ShallowBASE_Rev4.indd
WALL/SHALLOW
BASE UNIT
1000
WALL/SHALLOW BASE
Assembly Guide
1000 Wall
1000 Base
Shallow

For Internal Use: FI.WR.INS.036_WKIN00126_MULTI_1000_2Dr_WALL_ShallowBASE_Rev4.indd
Page 1
WALL/SHALLOW
BASE UNIT
1000
WALL/SHALLOW BASE
Assembly Guide
BEFORE YOU START
INSTALLATION
SHOULD BE
PERFORMED BY A
COMPETENT
PERSON ONLY.
THIS PRODUCT COULD
BE DANGEROUS
IF INCORRECTLY
INSTALLED
Panel A
x1 Back Panel
Hanging Bracket
x2 Inc Screws
(F) x8
Wooden Dowel
REQUIRED TOOLS
NOT to be used
with CAM DOWEL
& CAM LOCK
(G) x8
Cam Dowel
(Expanding)
(H) x8
Cam Lock
(K) x4
30mm
Screw
(P) x4
45mm
Screw
(L) x8
15mm
Screw
(S) x4
20mm
Screw
(M) x4
Cover Cap
(N) x2
Door
Buer
(Z) x10
Shelf Peg
Plastic
(T) x12
Back Panel
Support Clip
Hanging Bracket Plate
x2 (Screws Not Included)
Hinge Mounting Plate
x4 Inc Screws
Hinge
x4 Inc Screws
Corner Gusset
x2
Hanging Bracket
Cover Cap
x2
Panel B
x2 End Panel
Panel C
x2 Base Panel
Frontal
(packed separately)
x2
Muntin D
x1
Loose Shelf
x2

For Internal Use: FI.WR.INS.036_WKIN00126_MULTI_1000_2Dr_WALL_ShallowBASE_Rev4.indd
Page 2
WALL/SHALLOW
BASE UNIT
1000
WALL/SHALLOW BASE
Assembly Guide
Step 1.
Seat dowel (F) into
holes in end panel (B)
as shown.
Step 3.
Attach panels x2 (C) to panel
(B), using cam dowels (G)
& cam locks (H) (in blue),
and also using dowels (F)
(in orange) in positions as
shown.
Step 4.
Slide panel (A) into the groove
of panels (B) and x 2 (C).
Step 5.
Insert cam lock (H).
Hand tighten all cam locks
(H), this will expand the
cam dowels (G) and tighten
the unit together.
NB. All Cam Locks (H) are to be positioned facing the
outside of the unit Carcase, for ease of tightening.
Do not use power tools with
cam dowel (G) or cam lock (H)
B
A
C
C
Seat (G)
cam dowel
into hole as
shown.
BB
C C
H
H
G
G
View from underside View from underside
Step 2.
Seat cam dowel (G)
into holes in end
panel (B) as shown.
Dowel (F)
& Cam Dowel (G)
location detail
G
G
FF
FF
G
G
B

For Internal Use: FI.WR.INS.036_WKIN00126_MULTI_1000_2Dr_WALL_ShallowBASE_Rev4.indd
Page 3
WALL/SHALLOW
BASE UNIT
1000
WALL/SHALLOW BASE
Assembly Guide
Step 6.
Seat dowel (F) into holes in
both panels (B) as shown.
Step 8.
Attach panel (B) to panels
(C) using cam dowels (G)
& cam lock (H) (in blue)
and also using dowels (F)
(in orange) in positions as
shown. Ensure panel (A) is
seated into the groove of
panel (B).
Step 9.
Insert cam lock (H).
Hand tighten all cam locks
(H), this will expand the
cam dowels (G) and tighten
the unit together.
NB. All Cam Locks (H) are to be positioned facing the
outside of the unit Carcase, for ease of tightening.
Do not use power tools with
cam dowel (G) or cam lock (H)
B
B
A
C
C
Dowel (F)
& Cam Dowel (G)
location detail
G
G
F
F
F
F
G
G
B
Seat (G)
cam dowel
into hole as
shown.
BB
C C
H
H
G
G
View from underside View from underside
Step 7.
Seat cam dowel (G)
into holes in end
panel (B) as shown.

For Internal Use: FI.WR.INS.036_WKIN00126_MULTI_1000_2Dr_WALL_ShallowBASE_Rev4.indd
Page 4
WALL/SHALLOW
BASE UNIT
1000
WALL/SHALLOW BASE
Assembly Guide
B
A
C
B
A
T
T
T
T
T
T
TT
TT
TT
B
From Base
From Top
126mm
126mm
94mm
94mm L
L
Step 13.
Attach hinge mounting plates onto end panels (B) in locations shown
using 4 x screws (L)
Hinge side to be mounted in accordance to customer kitchen plan.
Step 11.
Slide the back panel clips
(T)
into the groove of both
panels (B) & (A).
The back panel clips (T)
should be evenly spaced as
shown and positioned to
allow the hanging bracket
and corner gussets to
be tted. Once in place,
tighten screw.
Step 10.
Ensure Carcase is square.
C
C
P
P
B
D
B
Step 12.
Join muntin
panel (D), to
both panels (C)
using 4 x 45mm
screws (P) as
shown.
T
T
A
B

For Internal Use: FI.WR.INS.036_WKIN00126_MULTI_1000_2Dr_WALL_ShallowBASE_Rev4.indd
Page 5
WALL/SHALLOW
BASE UNIT
1000
WALL/SHALLOW BASE
Assembly Guide
Step a
Insert Hanging
Bracket into pre-drilled holes
Step 13. Hanging Brackets steps a,b & c to be carried
out on both sides as shown
WALL CABINETS ONLY
Step c
Secure with provided
2 x 20mm screws (S) per bracket
Step b
Rotate locking
lever 180 degrees
S
S
Detail A Detail A Detail A
Step 14.
Secure Corner Gussets
to the bottom left and
right hand side of the
wall unit using
4 x 15mm screws (L)
per plate.
L
L
L
L
Detail B
Pilot
hole
M
Detail B
Step 15.
Drill a small pilot hole through the centre of the Corner Gussets.
Use this hole at the end of the process to screw through and
into the wall. Cover the screw heads using the cover caps (M)
provided.
Screws for xing to walls are not provided as these vary
depending on your wall material and construction. Ensure
appropriate xings for wall constructions are used.
A
B
for Shallow Base see pages 7 & 8
`
Care to be taken. Hanging procedure
is neccesary for a safe installation.

For Internal Use: FI.WR.INS.036_WKIN00126_MULTI_1000_2Dr_WALL_ShallowBASE_Rev4.indd
Page 6
WALL/SHALLOW
BASE UNIT
1000
WALL/SHALLOW BASE
Assembly Guide
WALL CABINETS ONLY
Step 16.
Measure appropriately and attach the 2 x hanging bracket plates onto the
wall screwing through the provided holes into your wall.
Screws for xing to walls are not provided as these vary depending
on your wall material and construction. Ensure appropriate xings for
wall construction are used.
Step 17.
Hang the cabinet using
the brackets to hook
onto the plate as shown
Step 18.
Using points a, b & c adjust the Cabinet to suit.
Step 19.
Screw into any side units using the
provided 2x 30mm screws (K) to
secure the unit. Screw just to the
rear of the hinge plate then place a
cover cap on the head to conceal it.
Step a.
Rotate the screw clockwise
to move the cabinet up.
Anti-clockwise for down.
Step b.
Adjust the depth
using centre
screw.
Step c.
Screw the red screw until it
touches the plate to lock
in position.
Hanging
Bracket
viewed though
Back Panel
b
C c
a
a
b
Hanging Bracket
Plate
K

For Internal Use: FI.WR.INS.036_WKIN00126_MULTI_1000_2Dr_WALL_ShallowBASE_Rev4.indd
Page 7
WALL/SHALLOW
BASE UNIT
1000
WALL/SHALLOW BASE
Assembly Guide
Step 20.
Secure Corner Gussets to the top left and right
hand side of the wall unit using 4 x 15mm
screws (L) per plate.
L
L
LL
Corner Gusset
Detail
View though
Back Panel
Pilot
hole
M
Step 21.
Drill a small pilot hole through the centre of the
Corner Gussets. Use this hole at the end of the
process to screw through and into the wall. Cover
the screw heads using the cover caps (M) provided.
Screws for xing to walls are not provided as
these vary depending on your wall material and
construction. Ensure appropriate xings for wall
constructions are used.
Step 22.
Screw into any side units using the provided 2x 30mm
screws (K) to secure the unit. Screw just to the rear of
the hinge plate then place a cover cap on the head to
conceal it.
K
SHALLOW BASE CABINETS ONLY
for WALL see pages 5 & 6
`

For Internal Use: FI.WR.INS.036_WKIN00126_MULTI_1000_2Dr_WALL_ShallowBASE_Rev4.indd
Page 8
WALL/SHALLOW
BASE UNIT
1000
WALL/SHALLOW BASE
Assembly Guide
Ensure legs are rotated as shown so that part
of it is supporting the end panels (B).
Step 24.
Push leg rmly down into leg base.
Adjust legs to 155mm before turning carcass
upright. Once in situ level accordingly.
B
C
L
L
L
L
B
C
Step 23.
Secure each of the legs into place with 4 x 15mm
Screws (L) per leg base.
LEG POSITION
DIAGRAM
FRONT
45 45
70
70
70 70
B
B
SHALLOW BASE CABINETS ONLY

For Internal Use: FI.WR.INS.036_WKIN00126_MULTI_1000_2Dr_WALL_ShallowBASE_Rev4.indd
Page 9
WALL/SHALLOW
BASE UNIT
1000
WALL/SHALLOW BASE
Assembly Guide
Step 25.
Insert hinge in top & bottom
holes as shown.
Step 26.
Secure hinges by tightening
2 x screws with hinge dowels
attached. These are already
positioned within the hinges.
Step 27.
Attach the door to unit
where required.
To attach door
clip hinge onto hinge
plate and click to secure.
Step 29.
Fit cover caps to hinge.
Adjust Soft-Close to suit.
Step 28.
Adjust hinge to suit. As shown below.
To adjust hinge using a screw
driver, tighten or loosen as
required at points 1& 2.
Point 1 - In - OUT
Point 2-Left - Right
12
FRONTAL HINGE
ADJUSTMENT
To Release door
Pull catch as shown,
to release hinge
from the hinge plate.
View from Inside of Carcass
Hinge Plates
Hinge Cover Caps