Wren Kitchens BASE UNIT 600 Built Under Oven Housing User manual

BASE UNIT
600 Built Under Oven Housing
Assembly Guide
For Internal Use: FI.WR.INS.031_WKIN00110_BASE_600_BUOH_Rev3.indd

BASE UNIT
600 Built Under Oven Housing
Assembly Guide
For Internal Use: FI.WR.INS.031_WKIN00110_BASE_600_BUOH_Rev3.indd
Page 1
(F) x16
Wooden Dowel
(G) x12
Cam Dowel
(Expanding)
(H) x12
Cam Lock
(K) x4
30mm
Screw
(L) x26
15mm
Screw
(M) x4
Cover
Cap
BEFORE YOU START
INSTALLATION
SHOULD BE
PERFORMED BY A
COMPETENT
PERSON ONLY.
THIS PRODUCT COULD
BE DANGEROUS
IF INCORRECTLY
INSTALLED
Panel B
x2 End Panel
Panel E
x2 Rail Panel
Legs
x4 Filler F
(Packed separately) x1
Filler G
(Packed separately) x1
Panel C
x1 Base Panel
REQUIRED TOOLS
NOT to be used
with CAM DOWEL
& CAM LOCK
Large Bracket
x2
Small Bracket
(FF)
x2
Dummy Fixing
Clip
x2 Inc Screws

BASE UNIT
600 Built Under Oven Housing
Assembly Guide
For Internal Use: FI.WR.INS.031_WKIN00110_BASE_600_BUOH_Rev3.indd
Page 2
Step 1.
Seat dowel (F)
into holes in
panels as shown.
Step 2.
Seat cam dowel (G)
into holes in panels
as shown.
Step 3.
Attach panels (C) & (E) to
panels (B), using cam dowel (G)
& cam lock (H) (in blue),
and also using dowels (F) (in
orange) in positions as shown.
Step 4.
Join panels (C) & (E) to
(B). Insert cam lock (H).
All Cam Locks (H) are to be positioned facing the
outside of the unit carcass, for ease of tightening. Do NOT use power tools with
cam dowel (G) or cam lock (H)
Dowel (F)
& Cam Dowel (G)
location detail
Seat (G)
cam dowel
into hole as
shown.
GG FF FF
FF F
FG
G
GG GG FF FF
B
B
B
EE
C
B B
View from underside View from underside
BB
CC
H
H
G
G

BASE UNIT
600 Built Under Oven Housing
Assembly Guide
For Internal Use: FI.WR.INS.031_WKIN00110_BASE_600_BUOH_Rev3.indd
Page 3
Step 5.
Secure each of the legs into place with
4 x 15mm screws (L) as shown.
Leg position diagram
Front
C
B
L
L
LL
B
B
B
E
B
C
Step 6.
Push leg rmly down into leg base.
Adjust legs to 155mm before turning carcass
upright. Once in situ level accordingly.
C
C
B
B
50mm
85mm

BASE UNIT
600 Built Under Oven Housing
Assembly Guide
For Internal Use: FI.WR.INS.031_WKIN00110_BASE_600_BUOH_Rev3.indd
Page 4
Worktop
Screw up through the front rail into
your worktop to secure it in place.
Screws for attaching to worktop are
not supplied as these vary depending
on worktop material and thickness. Ensure
appropriate xings for attaching worktop are
used. Please refer to the specialist worktop
supplier if these are required for solid surface
worktops.
Securing to Adjacent Units
Screw into any side units using
the 30mm screws (K) provided to
secure to unit. Screw at the top and
bottom of both sides of the unit, place a
cover cap (M) on the head to conceal it.
L Brackets
Use 2 x 15mm screws (L) to secure each
of the L brackets to the cabinets at either side.
Then screw up through into the worktop as shown.
Screws for attaching to worktop are
not supplied as these vary depending
on worktop material and thickness. Ensure
appropriate xings for attaching worktop are
used. L brackets should only be tted for securing
wood and laminate worktops, please refer to the
specialist worktop supplier if these are required
for solid surface worktops.
L
L
K

BASE UNIT
600 Built Under Oven Housing
Assembly Guide
For Internal Use: FI.WR.INS.031_WKIN00110_BASE_600_BUOH_Rev3.indd
Page 5
Step 7.
Use 15mm screw (L) per small L Bracket (FF)
to secure to inside face of Filler (G). Attached
equally spaced as shown.
Step 8.
Align Filler (G) to unit ensuring it
is in line with adjacent units.
Secure Filler (G) with Small L
bracket (FF) to Base of unit with
15mm Screw (L) as shown.
L
L
FF
FF
FF
Filler F
Filler G
15.5mm
155mm 155mm
View from bottom of unit
from top
inside face
inside face
G
FF
G
Small Bracket
G

BASE UNIT
600 Built Under Oven Housing
Assembly Guide
For Internal Use: FI.WR.INS.031_WKIN00110_BASE_600_BUOH_Rev3.indd
Page 6
Step 9.
Secure dummy xing clip Parts (B)
onto the inside face at the bottom of
panel (F), 17mm from the edge spaced
evenly either side as shown, using
screws (L). Align so frontal is in line
with adjacent frontals.
Step 11.
Align and push panel (F) into place. Ensure
frontal is in line with adjacent units. Space
appropriately from carcass.
L
Part A
Part A
L
L
45mm
17mm 17mm
View from inside of unit
from top
inside face
inside face
from top
F
FB
BB
B
E
Dummy Fixing Clip
B
Step 10.
Secure dummy xing clip parts (A) onto both
End Panels (B) using 2 x15mm screws (L)
each, as shown. The top screw hole is to be
positioned 45mm from the top of the panel
(marked by an indentation).
Part B
F
F
Part B
Front