Wren Kitchens Industrial Island User manual

INDUSTRIAL
Assembly Guide
For Internal Use: FI.WR.INS.095_WKIN00243_IndUnit_Assembly_Rev1.indd
Sample arrangements
cabinets sold seperately
Tower
Island

For Internal Use: FI.WR.INS.095_WKIN00243_IndUnit_Assembly_Rev1.inddPage 1
INDUSTRIAL
Assembly Guide
DOORSAFE
REQUIRED TOOLS
INSTALLATION SHOULD
BE PERFORMED BY A
COMPETENT PERSON ONLY.
THIS PRODUCT COULD
BE DANGEROUS IF
INCORRECTLY INSTALLED.
PRIOR TO INSTALLATION, FIXTURES
INCLUDING DOORS, DRAWERS, LOOSE
SHELVES & LEGS SHOULD BE REMOVED
TO ENSURE A SAFE INSTALLATION.
WREN RECOMMENDS USING DOORSAFE
FOR TEMPORARY STORAGE.

Page 2
INDUSTRIAL
TOWER
Assembly Guide
Conguration may vary in accordance to specic customer kitchen plan
cabinets Included seperately
End Components Extension Components
Legs Legs
35mm Bolt
& Washer
16mm Bolt
& Washer
(K)
30mm
Screw
(L)
16mm
Screw
Detail A Detail B
AB
End Frame Shelving
(330, 570)
600
Extension Frame Shelving
(330, 570)
600
Wall Securing
Bracket
For Internal Use: FI.WR.INS.095_WKIN00243_IndUnit_Assembly_Rev1.indd

For Internal Use: FI.WR.INS.095_WKIN00243_IndUnit_Assembly_Rev1.inddPage 3
INDUSTRIAL
TOWER
Assembly Guide
For Internal Use: FI.WR.INS.095_WKIN00243_IndUnit_Assembly_Rev1.indd
Step 1.
Using 4 x 35mm Bolt & Washer attach End Frame Shelf as shown,
to secure to End or Internal Legs, where applicable.
Adjust leg height per frame by twisting to suit.
For Shelf Positions see Specic Customer Kitchen Plan.
Step 2.
Repeat shelf assembly as appropriate
to customer, to form End/Extension
Tower Frame, as shown.
Step 3.
Attach assembled Tower Frames
where appropriate to customer as shown.
End/Extension Shelf
End/Extension Shelf
End/Internal Leg
End/Internal Leg
Tower Frame Assembly
End/Internal Legs
Sample
arrangements
Extension
Frame Shelf
End
Frame Shelf
End/Internal Leg
End/Internal Leg
End /Extension
Frame Shelf
BTM
End/Internal Leg
TOP
End/Internal
Frame Shelf
Bolt Location
Btm of End/Internal Leg

For Internal Use: FI.WR.INS.095_WKIN00243_IndUnit_Assembly_Rev1.indd Page 4
INDUSTRIAL
TOWER
Assembly Guide
Step 6.
Using 2 x 16mm
Screws (L) per
connecting plate,
screw up through
xing plate into the
base panel of each
unit as shown.
Step 5.
Where applicable,
position door and drawer
cabinets in accordance
to customer specic
frontal thickness.
Ensure correct
positioning of cabinets.
Step 4. Securing Metal Frame to Wall
To secure tower frames, use the provided brackets to secure to wall.
Secure bracket to top frame shelf at both sides using 16mm Bolt &
Washer. Then screw through into wall as shown.
Screws for xing to walls are not provided as these vary
depending on your wall material and construction.
Ensure appropriate xings for wall constructions are used.
Cabinet Installation
Front
Tower Assembly
Connecting
Plate
LL
View from
underside of unit
See Customer Specic Order for requirements.
Top Shelf
Top Shelf
To Wall
Decor
End
Decor
End
Decor
Panel
Step 7. Decor Panels
Measure and cut
appropriately to ensure full
cover of bare carcase.
If necessary, scribe decor end
panel to end of unit.
K
Step 8. Decor Panel Installation
Ensure cabinets are located accordingly. Clamp décor end panels adjacent to the
unit inside of the frame and screw through the unit into the décor panel using
30mm screws (K). Screw at the top and bottom of unit away from xings such as
drawers and hinges. For upper décor panels screw through the top of the unit at
the Front/Back. Place cover caps on the heads of screws to conceal.
Step 9. Glass Shelf Installation
For glass shelf installation only, install 1x rubber stopper
provided with glass shelf on each connecting plate as shown.
Position glass shelf with care.
Rubber
Stopper
Please ensure steps are
followed for a safe installation.
OR
Cabinet
Cabinet
Frtl
THK
Flush
Front
Front

For Internal Use: FI.WR.INS.095_WKIN00243_IndUnit_Assembly_Rev1.indd For Internal Use: FI.WR.INS.095_WKIN00243_IndUnit_Assembly_Rev1.indd Page 5
INDUSTRIAL
ISLAND
Assembly Guide
35mm Bolt
& Washer
16mm Bolt
& Washer
End Components:
Internal Components:
Internal Frame Shelving
End Frame Shelving
(1215)
600-1000
(1215)
300-1000
(975)
600-1000
(975)
300-1000
(645)
600-1000
(645)
300-1000
Legs
Legs
Conguration may vary in accordance to specic customer kitchen plan
cabinets sold seperately
Unit Spacers
Detail A
Detail B
B
A

For Internal Use: FI.WR.INS.095_WKIN00243_IndUnit_Assembly_Rev1.indd Page 6
INDUSTRIAL
ISLAND
Assembly Guide
Step 1.
Using 4 x 35mm Bolt & Washer attach End Frame Shelf as
shown, to secure to End or Internal Legs, where applicable.
Adjust leg height per frame by twisting to suit.
For Shelf Positions see Specic Customer Kitchen Plan.
Step 2.
Using 4 x 35mm Bolt & Washer secure Internal Frame
Shelf to Internal Legs where applicable as shown.
Btm of End/Internal Leg
End Leg
End Frame
For shelf positions see specic
customer kitchen plan
End Frame Shelf
Internal Frame Shelf
End Frame Shelf
End Leg
Internal Leg
End Leg
End Shelf
End Shelf
Island Frame Assembly
End Frame Shelf
Bolt Location
End Leg
End Frame Shelf
End Leg
Internal Leg
Internal Leg

For Internal Use: FI.WR.INS.095_WKIN00243_IndUnit_Assembly_Rev1.indd
For Internal Use: FI.WR.INS.095_WKIN00243_IndUnit_Assembly_Rev1.inddPage 7
INDUSTRIAL
ISLAND
Assembly Guide
Step 7. Glass Shelf Installation
For glass shelf installation only, install 1x rubber stopper
provided with glass shelf, on each connecting plate as
shown. Position glass shelf with care.
Step 3. Worktop Installation
To secure worktop, screw up through connecting plates into your worktop to secure
it in place. Screws for attaching to worktop are not provided as these vary
depending on materials, thickness and construction.
Ensure appropriate xings for worktop construction are used. Please refer to
the specialist worktop supplier if these are required for solid surface worktops.
Island Assembly
Step 6.
Ensure cabinets are located accordingly.
Screw through unit into Spacer/Decor End Panel
using 30mm screws (K) provided. Screw as shown
at top and bottom of unit, away from ttings.
Place a cover cap on head of screw to conceal.
K
Decor End
Length to suit
Spacer
Spacer
Measure and cut
appropriately to ensure
full cover of bare carcase.
Where applicable, scribe
Decor End panel to the
end of unit. Clamp Decor
End panel adjacent to the
unit within the frame.
OR
Rubber
Stopper
See customer specic order for requirements.
Front
Step 4. Cabinet Installation
Where applicable, position door and drawer cabinets in
accordance to customer specic frontal thickness.
Measure and cut provided spacer panel appropriately.
Position ush against internal units at both sides, as shown.
Ensure correct positioning of cabinets.
Cabinet
Cabinet
Frtl
THK
Flush
Front
Front
Please ensure steps are
followed for a safe installation.
Step 5.
Decor Panel Installation
Cabinet Securing using Spacer/Decor Panel