Wren Kitchens TOWER UNIT 2070 x 600 50/50 User manual

2070 x 600
50/50
2070 x 600
70/30
2250 x 600 Tall
50/50
2250 x 600 Tall
70/30
For Internal Use: FI.WR.INS.059_WKIN00180_TOWER_600_2DrBoilerHousing_Rev2.indd
TOWER UNIT
Boiler Housing
Assembly Guide

BEFORE YOU START
INSTALLATION
SHOULD BE
PERFORMED BY A
COMPETENT
PERSON ONLY.
THIS PRODUCT COULD
BE DANGEROUS
IF INCORRECTLY
INSTALLED
REQUIRED TOOLS
NOT to be used
with CAM DOWEL
& CAM LOCK
Panel B
x2 End Panel x2 Base Panel
Panel C Btm Panel C Top Panel E
x2 Rail
Legs
x5
Frontal (packed separately)
x2
70/30 OPTION
50/50 OPTION
Sml L Bracket
(FF) x4
Hinge Mounting Plate
x4 Inc Screws
Hinge
x4 Inc Screws
(U) x2
Fixing Plate
(F) x16
Wooden Dowel
(L) x24
15mm
Screw
(G) x16
Cam Dowel
(Expanding)
(H) x12
Cam lock
(M) x4
Cover Cap
(K) x10
30mm
Screw
(N) x2
Door Buer
Lge L Bracket
x2
(Z) x24
Shelf Peg
Plastic
For Internal Use: FI.WR.INS.059_WKIN00180_TOWER_600_2DrBoilerHousing_Rev2.indd For Internal Use: FI.WR.INS.059_WKIN00180_TOWER_600_2DrBoilerHousing_Rev2.inddPage 1
TOWER UNIT
Boiler Housing
Assembly Guide

Step 3.
Attach panels (CTop,Btm) and (E) to panels (B),
using cam dowel (G) and also using Dowels (F) (in orange)
in positions as shown.
NB. All CAM LOCK (H) are to be positioned facing
the outside of the unit carcass, for ease of tightening.
Step 4.
Join panels (C) & (E) to (B).
Insert cam lock (H).
Do NOT tighten until Step 6.
Do not use power tools with
cam dowel (G) or cam lock (H)
GFF G
G F F G
Btm
Top
B
RHLH
GFFG
GFFG
B
G
F
F
G
F
F
G
F
F
G
F
F
Seat (G)
cam dowel
into hole as
shown.
B
B
View from underside View from underside
H
G
G
H
B
E
E
C Btm
C Top
C Top C Top
B
Dowel (F)
& Cam Dowel (G)
location detail
Step 2.
Seat dowel (F) into
holes in both end
panels (B)
as shown.
Step 1.
Seat cam dowel (G) into
holes in both end panels (B)
as shown.
For Internal Use: FI.WR.INS.059_WKIN00180_TOWER_600_2DrBoilerHousing_Rev2.indd Page 2
TOWERUNIT
Boiler Housing
Assembly Guide

B
Step 5.
Secure each of the legs
into place with
2 x 15mm screws (L) per leg
Step 7.
Push leg rmly down into leg base.
Adjust legs to 155mm before turning carcass upright.
Once in situ level accordingly.
Step 6.
Lightly hit centre peg of leg base with
hammer until ush with the leg base.
Ensure legs are rotated as shown so that part
of it is supporting the end panels (B).
Front legs should have at edge to the front.
Front
Front
BB
L
L
B
B
Leg position diagram
It is important to lift the unit onto its legs. Do not tilt as
depicted in the image.
C Btm
C Btm
C BtmC Btm
C Btm
B
For Internal Use: FI.WR.INS.059_WKIN00180_TOWER_600_2DrBoilerHousing_Rev2.inddPage 3
TOWER UNIT
Boiler Housing
Assembly Guide
For Internal Use: FI.WR.INS.059_WKIN00180_TOWER_600_2DrBoilerHousing_Rev2.indd

Step 8.
Attach hinge plates onto end panels (B) In
locations shown using 8 x 15mm screws (L)
Hinge side to be mounted in accordance
to customer kitchen plan.
70/30
HINGE
POSITION
50/50
HINGE
POSITION
70/30
1826mm 1826mm
846mm
1086mm
626mm
866mm
126mm 126mm
1794mm 1794mm
814mm
1054mm
594mm
834mm
94mm 94mm
50/50
B B
L
L
L
L
L
L
L
L
From Base From Base
For Internal Use: FI.WR.INS.059_WKIN00180_TOWER_600_2DrBoilerHousing_Rev2.indd Page 4
TOWER UNIT
Boiler Housing
2070
Assembly Guide

Step 9.
Attach hinge plates onto end panels (B) In
locations shown using 8 x 15mm screws (L).
Hinge side to be mounted in accordance to
customer kitchen plan.
N.B.
For appliance shelf, secure to panel (B)
using 4 x brackets (FF) locate according to
customer appliance requirements.
70/30
HINGE
POSITION
50/50
HINGE
POSITION
70/30
2006mm 2006mm
846mm
1026mm
626mm
806mm
126mm 126mm
1974mm 1974mm
814mm
994mm
594mm
774mm
94mm 94mm
50/50
B B
L
L
L
L
LL
LL
From Base From Base
For Internal Use: FI.WR.INS.059_WKIN00180_TOWER_600_2DrBoilerHousing_Rev2.inddFor Internal Use: FI.WR.INS.059_WKIN00180_TOWER_600_2DrBoilerHousing_Rev2.indd
TOWER UNIT
Boiler Housing
2250
Assembly Guide

Secure tower to the wall using L brackets.
Use 2 x 15mm screws (L) tosecure each of the L
brackets to the cabinets at either side. Then screw
through into the wall as shown.
Screws for xing to walls are not provided as
these vary depending on your wall material
and construction. Ensure appropriate xings
for wall constructions are used.
Screw into any side units using
the 30mm screws (K) provided to secure to unit.
Screw just to the rear of the Hinge Mounting Plate,
at the top and bottom of both sides of the unit,
place a cover cap on the head to conceal it.
L
L
K
Page 6
For Internal Use: FI.WR.INS.059_WKIN00180_TOWER_600_2DrBoilerHousing_Rev2.indd
TOWER UNIT
Boiler Housing
Assembly Guide

See Customer Specic Kitchen Plan
For Tower Frontals
Fixing plates
Step 10.
Insert hinge where required
in holes as shown.
Step 11.
Secure hinges by tightening
2 x screws with hinge dowels
attached. These are already
positioned within the hinges.
Step 13.
Adjust hinge to suit. As shown below.
U
U
Step 12.
Align doors to join together
using 2 x xing plates (U)
to the back of both frontals
ensure a 3mm gap is
maintained between each
frontal once xed together.
Screw in place using 4 x 15mm
screws per xing plate.
Hinge cover caps
The top and bottom
hinges MUST be
adjusted to the SAME
STRENGTH.
View from Inside of Carcass
To adjust hinge using a screw
driver, tighten or loosen as
required at points 1& 2.
Point 1- In - Out
Point 2- side - side
12
FRONTAL HINGE
ADJUSTMENT
To Release door
Pull catch as shown,
to release hinge
from the hinge
plate.
Step 14.
Fit cover caps to hinge.
Adjust Softclose to suit.
For Internal Use: FI.WR.INS.059_WKIN00180_TOWER_600_2DrBoilerHousing_Rev2.indd For Internal Use: FI.WR.INS.059_WKIN00180_TOWER_600_2DrBoilerHousing_Rev2.inddPage 7
TOWER UNIT
Boiler Housing
Assembly Guide

For Internal Use: FI.WR.INS.059_WKIN00180_TOWER_600_2DrBoilerHousing_Rev2.indd Page 8
TOWERUNIT
Boiler Housing
Assembly Guide

For Internal Use: FI.WR.INS.059_WKIN00180_TOWER_600_2DrBoilerHousing_Rev2.indd For Internal Use: FI.WR.INS.059_WKIN00180_TOWER_600_2DrBoilerHousing_Rev2.inddPage 9
TOWER UNIT
Boiler Housing
Assembly Guide